Lexmark C532dn User Manual

Note: All life estimates for printer supplies assume printing on letter- or A4-size plain paper.
Ordering toner cartridges
When 88 Cyan cartridge low, 88 Magenta cartridge low, 88 Yellow cartridge low, or 88 Black
cartridge low appears on the control panel or when the print becomes faded, first try to extend the life of the
specified cartridge:
1Remove the specified toner cartridge.
2Rotate the toner cartridge as shown, and firmly shake the cartridge up and down several times to redistribute
the toner...

Part namePart numberFor printer(s)
Cyan High Yield Toner CartridgeC5242CHC532, C534
Magenta High Yield Toner CartridgeC5242MHC532, C534
Yellow High Yield Toner CartridgeC5242YHC532, C534
Black High Yield Toner CartridgeC5242KHC534
Cyan Return Program Toner
CartridgeC5220CSC530, C532, C534
Magenta Return Program Toner
CartridgeC5220MSC530, C532, C534
Yellow Return Program Toner
CartridgeC5220YSC530, C532, C534
Black Return Program Toner
CartridgeC5220KSC530, C532, C534
Cyan Return Program Toner...

Ordering a waste toner box
When 82 Waste Toner Box Nearly Full or 82 Replace Waste Toner Box appears, you need to order
a replacement waste toner box.
Part numberPart name
C52025XWaste toner box
Ordering a fuser
When Fuser Life Warning appears, replace the fuser soon. Make sure one is on order.
When Replace Fuser appears, replace the fuser immediately. For installation information, see the documentation
that came with the fuser.
Part numberPart name
40X3569 (120V/50–60Hz)
40X3570 (220–240V/50–60Hz)...

Moving the printer to another location
The printer and options can be safely moved to another location by following these precautions:
Remove all printer options before moving the printer.
Any cart used to move the printer must have a surface able to support the full footprint of the printer. Any cart
used to move the options must have a surface able to support the dimensions of the options.
Keep the printer in an upright position.
Avoid severe jarring movements.
Maintaining the printer
74
Downloaded...

Administrative support
Adjusting the brightness or contrast of the display
Note: These options are available on some models.
To adjust the brightness or contrast settings:
1Make sure the printer is on and Ready appears.
2From the control panel, press .
3Press  until Settings appears, and then press .
4Press  until Utilities Menu appears, and then press .
5Press  until Brightness appears, and then press .
Press 
 until Contrast appears, and then press .
6Press  to increase the setting or  to decrease the...

3Release both buttons when Performing Self Test appears.
The printer performs its power-on sequence, and then CONFIG MENU appears.
4Press  until Panel Menus appears, and then press .
5Press  until Enable appears, and then press .
Submitting Selection, Enabling Menus, and Panel Menus appear briefly.
6Press  until Exit Config Menu appears, and then press .
When Activating Menu Changes appears, the menus are enabled. Resetting the Printer appears
briefly, followed by a clock, and then Ready appears....

The following factory default settings are restored:
All downloaded resources in the printer memory are deleted. This includes fonts, macros, and symbol sets.
All settings return to the factory default settings except Display Language in the Setup menu and custom
settings in the Parallel, Serial, Network, Infrared, LocalTalk, USB, and Fax menus.
Adjusting Power Saver
1Make sure the printer is on and Ready appears.
2From the control panel, press .
3Press  until Settings appears, and then press .
4Press...

7When the process is finished, press .
8Press  until Exit Config Menu appears, and then press .
Resetting the Printer appears briefly, followed by a clock, and then Ready appears.
Disabling printer hard disk encryption
This functionality is only available when a printer hard disk is installed and working properly.
Warning: All files and resources on the printer hard disk will be deleted. Resources residing in the printer flash
memory or RAM will not be affected.
1Make sure the printer is turned off....

Notes:
A printer hard disk must be installed in the printer and working properly for the printer lockout functionality to be
available.
Some data will continue to be processed while the printer is locked. Reports such as user or event logs can be
retrieved from a locked printer.
To lock control panel menus:
1Open a Web browser. In the address line, enter the IP address of the printer or print server to be protected using
the format: http://ip_address/.
2Click Configuration.
3Under Other Settings, click...

IPSec supports two types of authentication:
Shared Key Authentication—Authenticates any ASCII phrase shared among all participating host computers.
This is the easiest way to configure when only a few host computers on the network use IPSec.
Certificate Authentication—Authenticates any host computer or subnet of hosts for IPSec. Each host computer
must have a public/private key pair. Validate Peer Certificate is enabled by default, requiring each host to have
a signed authority certificate that is...