LG Revere User Guide

							Getting Started with Your Phone
19
Installing the Battery
1. Press down on indentation near
the bottom of the battery cover
and slide the cover upwards to
remove it.
2. Align the battery contacts with
the terminals near the top of the
battery compartment and press
until you hear the “click”.
3. Align the battery cover and slide
it downwards until it clicks into
place.
Removing the Battery
1. Turn the phone off.
2. Press down on indentation near
the bottom of the battery cover
and slide the cover upwards to
remove it.3. Use the fingertip opening near
the bottom of the battery
compartment to lift the battery
out.
Charging the Battery
Your device comes with a cableless
wall adapter and a USB cable which
connect together to charge your
phone. To charge your phone:
NOTICEPlease use only an approved charging
accessory to charge your LG phone.
Improper handling of the
Charger/Accessory Port, as well as the
use of an incompatible charger, may cause
damage to your phone and void the
warranty.
1. Connect the USB cable into the
cableless wall adapter. When
connecting as shown below, the
LG logo on the USB cable
should face toward you.
Cableless Wall Adapter 
						

							Getting Started with Your Phone
20
2. Gently uncover the Charger/
Accessory Port, then plug the
end of the adapter into the
phone's Charger/Accessory Port
and the other end into an
electrical outlet.
The charge time varies depending
upon the battery level.
Charging with USB
You can use your computer to
charge your phone. To be able to
charge with the USB cable, you
may need to have the necessary
USB Driver installed on your PC
first. Connect one end of the USB
cable to the Charger/Accessory
Port on your phone and the other
end to the USB port on your PC.
NOTELow-power USB ports are not
supported, such as the USB
ports on your keyboard or 
bus-powered USB hub.
Battery Temperature
Protection
If the battery gets overheated, the
phone will automatically turn off.
When you turn the phone back on,
a message pops up alerting you
that the phone was powered off for
your safety.
Battery Charge Level
You can find the battery charge
level  at the top right corner of
the LCD screen. When the charge
level becomes low, the battery
sensor sounds a warning tone,
blinks the battery icon, and/or
displays a warning message. As the
charge level approaches empty, the
phone automatically switches off
without saving. 
Signal Strength
Call quality depends on the signal
strength in your area. You can tell
how much signal strength you have
by the number of bars next to the
signal strength icon : the more
bars, the stronger the signal. If
NOTEPlease make sure that the  'B' side faces
up before inserting a charger or USB
cable into the Charger/Accessory Port
of your phone.  
						

							21
you’re having problems with signal
quality, move to an open area or,
when inside a building, try moving
near a window.
Turning the Phone On and
Off
Turning the Phone On
1. Insert the battery and connect
the phone to an external power
source if the battery level is low.
2. With the flip open, press the
PWR/END Keyuntil the
LCD screen lights up.
Turning the Phone Off
With the flip open, press and hold
the 
PWR/END Keyuntil
the LCD screen turns off.
Making Calls
1. Make sure the phone is turned
on. 
If not, open the flip and press
the 
PWR/END Keyfor
about three seconds. 
If necessary, enter the lock code.
2. Enter the phone number.3. Press the 
Send Keyto
dial the call.
4. Press the 
PWR/END Key
to end the call.
NOTEYour phone has a Voice
Commands feature that also lets
you make calls by saying a
phone number or Contact name.
Correcting Dialing Mistakes
While entering a phone number,
press the 
CLR Keyonce to
erase the last digit entered, or hold
it down for at least two seconds to
delete all the digits.
Redialing Calls
With the flip open, press the SEND
Key
twice to redial the last
number dialed.
Receiving Calls
1. When the phone rings or
vibrates, you can answer the call
by simply opening the flip. 
NOTEIf the 'Flip Open' (Menu >
Settings & Tools > Call Settings >
Answer Options) answer option
is NOT MARKED, you can:
Open the flip and press the 
						

							Left Soft Key [Quiet]to
mute the ringing or vibration
for that call.
Open the flip and press the
Right Soft Key [Ignore]to
end the call or send it directly
to Voicemail.
Open the flip and press 
[TXT]to end the call and send
a quick text message.
2. Press the PWR/END Key
to end the call, or simply close
the flip. 
Screen Icons
When the phone is on, the top line
of the LCD screen displays phone
status icons. 
To see the icon glossary, with the
flip open, go to 
MENU > Settings
& Tools  > Phone Info > Icon
Glossary
on your phone.
22
Getting Started with Your Phone 
						

							Quick Access to Convenient Features
23
Vibrate Mode
Sets the phone to vibrate instead of
ringing ( is displayed). To set
Vibrate Mode, with the flip open,
press and hold  . To return to
Normal Mode, press and hold 
again. 
Sounds Off
Quickly deactivate your phone's
sounds when you're in a place
where phone sounds would be
disruptive. 
From standby mode with the flip
open, press and hold the lower
volume key for 3 seconds.  To
return to normal sounds mode,
press and hold the upper volume
key.
Mute Function
The Mute Function prevents the
transmission of your voice to the
caller. To quickly activate Mute
while on a call, press the Left Soft
Key 
[Mute], then to unmute
press the Left Soft Key
[Unmute]again.
Quick Volume Adjustment
Quickly adjust ringer and earpiece
volumes by pressing the Volume
Keys  on the left side of the
phone. Press the upper volume key
to increase and lower volume key to
decrease the volume.
NOTEThe earpiece volume can only be
adjusted during a call and
Keypad Volume can only be
adjusted through the Sounds
Settings menu.
Quick Font Resize
When you view messages, enter
phone numbers, or view sub-menus,
press the Volume Keys  up or
down to quickly adjust the font
size. 3 levels (small, medium, large)
of font sizes are available.  
NOTENot supported on the Main
menu.
Call Waiting
During a call, one beep indicates
another incoming call. Press the
SEND Keyto answer it and
put the first call on hold. Press the
SEND Keyagain to return
to the first call.  
						

							24
Quick Access to Convenient Features
3-way call
You can talk with two people at the
same time with a three-way
conversation on your wireless
phone. Airtime and other charges,
which may include toll or long
distance charges, will apply for all
simultaneous calls until you end
one call. 
1. While on the first call, dial the
10-digit number of the second
person. 
2. Press the 
SEND Key. The
first person is automatically put
on hold while the call is made. 
3. When the second person
answers, press the 
SEND Key
to create a conference
call. 
4. If the second person does not
answer, press the 
SEND Key
twice to end the
connection and go back to the
first person. 
5. To end both conversations
completely, press the 
END Key
.
Caller ID
Caller ID displays the number
and/or name and picture (if
applicable) of the person calling
when your phone rings. 
Voice Commands
Voice Commands allow you to do
things by verbal command (e.g.,
make calls, check Voicemail, etc.).
With the flip open, press the 
Vo i c e
Commands Key
on the
keypad.
1.
CallSay "Call" and then call
someone simply by saying the
name or phone number.
2.
Send Msg toSay "Send
Message" and the command will
prompt you for the type of
message.
3.
Go toThis allows you to
access a menu within the phone.
4.
CheckThis allows you to
check out a wide range of items
such as 
Phone Status,
Voicemail, Message, Missed
Calls, Time, Signal Strength,
Battery Level, Volume, Balance,
Minutes, Payment
and My
Number
. 
						

							5.ContactsYou can look up
names in your Contacts as well
as manage your Contact List
including creating, erasing or
modifying.
6.
RedialSay "Redial" and the
phone will redial the last phone
number.
7.  
My VerizonThis command
provides you with direct access
to your Verizon Wireless account
information.
8.
HelpProvides a general
guideline to using Voice
Commands.
NOTEVoice Commands can also be
started with the designated key
on your Bluetooth
®device.
Please check the user manual of
the Bluetooth
®device for further
instructions.
Dial Search
Set the Dial Search setting to On
(see page 89) to easily find entries
in your Contacts.  From standby
mode with the flip open, press the
keypad key(s) with the first
letter(s) of the Contact name you
are trying to find.  A list of
matching names will be displayed
for you to select to call, message,
or view. 
25 
						

							26
Entering and Editing Information
Text Input
The following key functions are
available to help with text entry:
Left Soft Key: Press to
change the text input
mode.
Shift: Press to change
capitalization (initial cap,
caps lock, lowercase).
Next: Press to display
other matching words in
the database in T9 word
mode.
Space: Press to complete a
word and insert a space.
Clear: Press to delete a
single space or character.
Hold to delete words.
Punctuation: Press to
insert punctuation
symbols.
Text Input Modes
In a text field, press the Left Soft
Key  to select a text input
mode:
T9 Word/ Abc/ ABC/ 123/ 
T9 Palabra/ Symbols/ Quick
Text/ Simplified Chinese/ Korean
NOTET9 Palabra is the Spanish
counterpart of T9 Word which
utilizes accents, tildas, etc. for
correct Spanish word spelling.
Simplified Chinese supports
PinYin as entry mode.
Korean provides a key guide. To
use the key guide, select
Options > Show Key Guide. 
						

							Contacts in Your Phone’s Memory
27
Storing Basics
1. With the flip open, enter a number
(max. 48 digits), then press the
Left Soft Key 
[Save].
2. Use the Directional Key  to
highlight 
Add New Contact/
Update Existing
, then press  .
3. Use the Directional Key  to
highlight 
Mobile 1/ Home/
Business/ Mobile 2/ Fax
, then
press . 
4. Enter a name (max. 32
characters), and any additional
information, then press 
[SAVE].
NOTEIf you selected Update Existing
after you select the number type,
the contact information is
automatically updated.
Customizing Individual Entries
1. With the flip open, press the
Right Soft Key 
[Contacts],
then use the Directional Key
to highlight an entry.
2. Press the Left Soft Key 
[Edit].
3. Use the Directional Key to
highlight the information to
customize.4. Change the entry as you want,
then press 
[SAVE]to save
your changes.
Speed Dial
Allows you to set up your Speed
Dials.
1. With the flip open, press the
Right Soft Key 
[Contacts],
then use the Directional Key
to highlight an entry.
2. Press the Left Soft Key 
[Edit].
3. Use the Directional Key  to
highlight a phone number, then
press the Right Soft Key 
[Options].
4. Use the Directional Key  to
highlight 
Set Speed Dial, then
press .
5. Select a Speed Dial digit.
Enter a digit using the keypad,
then press [SET].
Use the Directional Key  to
highlight the Speed Dial digit,
then press 
[SET].
6. Press 
Ye sto confirm, then
press 
[SAVE] to update
your contact entry
. 
						

							28
Contacts in Your Phone’s Memory
Storing a Number with Pauses
Pauses allow you to enter additional
series of numbers to access
automated systems such as
Voicemail or credit billing numbers.
Pause types are: 
Wa i t(W) The phone stops dialing
until you press the Left Soft Key
[Release]to advance to the
following series of numbers. 
2-Sec Pause(P) 
The phone waits
two seconds before dialing the
next string of digits.
1. With the flip open, enter the
phone number, then press the
Right Soft Key 
[Options].
2. Use the Directional Key  to
highlight 
Add 2-Sec Pauseor
Add Wait, then press  .
3. Enter the additional number(s)
(e.g., pin number, credit card
number, etc.).
4. Press the Left Soft Key 
[Save].
5. Choose Add 
New Contact/
Update Existing
.
6. Choose 
Mobile 1/ Home/
Business/ Mobile 2/ Fax
.7.  Continue entering information
for the Contact entry as necessary.
NOTEIf you selected Update Existing
after you select the number
type, the contact information is
automatically updated. You do
not have the option to enter
additional information.
8. Press [SAVE]to update
your contact entry.
Adding a Pause to an Existing
Contact Entry
1. With the flip open, press the
Right Soft Key 
[Contacts].
2. Use the Directional Key to
highlight a Contact entry, then
press the Left Soft Key
[Edit].
3. Use the Directional Key  to
highlight the number, then press
the Right Soft Key 
[Options].
4. Press 
Add 2-Sec Pauseor
Add Wait.
5. Enter the additional number(s),
then press 
[SAVE]to
update your contact entry
.