Liesegang Ddv 2500 Projector User Manual

DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———AAAddddddeeennnddduuummm   
The Remote Interface Overview 
The following shows the remote interface main screens. 
Remote 
This screen shows the current status of the 
projector. 
Remote-2
This screen is used to control the projector. 
Administrator Settings
This screen allows the administrator to set a 
password and limit connections to the pro-
jector. 
— 6 —  

   RRRJJJ---444555   SSSeeettttttiiinnnggg   uuuppp   
IP Settings 
This screen allows the IP address to be set 
for static or DHCP. 
E-mail Settings 
Status messages for the projector can be 
emailed to the administrator or any other 
address.  
Some servers require a sender address, 
otherwise the email is blocked. So in most 
cases the Sender and Receiver addresses 
will be the same.  
The projector automatically emails status 
messages such as IP address, and Power 
state as shown below to the...

DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———AAAddddddeeennnddduuummm   
Setting up Remote Operation 
You should know some or all of the following address settings: 
- IP Address 
- Subnet Mask 
- Default Gateway 
- DNS Server 
- E-mail address for remote PC 
- Password (if required) for remote PC 
- Outgoing server (SMTP) for remote PC 
Important: 
Using a proxy server for your LAN may filter messages from the projector. Disable the proxy server to 
prevent this. 
 
The factory default IP address for the...

   RRRJJJ---444555   SSSeeettttttiiinnnggg   uuuppp   
– 9 –  

DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———AAAddddddeeennnddduuummm   
Enabling and Disabling Passwords 
The default setting is Disable and no password has been set. 
1. Click Administrator Settings.  
The Administrator Settings 
page opens. 
 
2. Check the Enable radio button 
and then click Set. 
or 
Check the Disable radio button 
and then click Set. 
 
3. Click your browser back button 
to go to the Input 
PASSWORD box. 
4. Enter the password and click 
Login. 
 
 
— 10 —  

   RRRJJJ---444555   SSSeeettttttiiinnnggg   uuuppp   
Setting the Maximum Connections 
Refer to the following to limit the amount of users that can log on to the projector. 
1. Click Administrator Settings.  
The Administrate Settings 
page opens. 
2. Enter the amount and click Set.  
 
 
– 11 –  

DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———AAAddddddeeennnddduuummm   
Retrieving a Forgotten Password 
Refer to the following to retrieve a forgotten password. 
1. Make sure the Enable radio but-
ton (next to Security Status) is 
selected and click Set. 
2. In the Input Password screen, 
click Forgot your Password? 
3. Enter your e-mail address and 
clikc Send. 
4. The current projector password 
is mailed to you in a format 
similar to this. 
 
 
 
— 12 —  

 
  
 
 
 
Liesegang Optoelectronics GmbH  Liesegang Corp. 
Kaistraße 5           1001 W. Cypress Creek Rd. 103
D-40221 Duesseldorf       Ft. Lauderdale, FL 33309 
Germany     USA 
Telefon  +49 (0) 211/ 3901-1    phone  (954) 489 23 01 
Telefax  +49 (0) 211/ 3901-227    fax  (954) 489 23 18 
[email protected]    [email protected] 
www.liese
gang.de     www.liesegangcorp.com
Technische Änderungen vorbehalten, Subject to modification