Liesegang Projector Dv 465 User Manual

							
10

Setting up
Connecting your devices
CAUTION  ►Turn off all devices prior to connecting them to the projector. 
Attempting to connect a live device to the projector may generate extremely 
loud noises or other abnormalities that may result in malfunction and/or damage 
to the device and/or projector.
►Use the accessory cable or a designated-type cable for the connection. 
Some cables have to be used with core set. A too long cable may cause a 
certain picture degradation. Please consult with your dealer for details. For 
cables that have a core only at one end, connect the core to the projector .
►Make sure that you connect devices to the correct port. Incorrect connection 
may result in malfunction and/or damage to the device and/or projector . 
NOTE  • Whenever attempting to connect a laptop computer to the projector, be sure 
to activate the laptop’s RGB external image output (set the laptop to CRT display or to 
simultaneous LCD and CRT display). For details on how this is done, please refer 
to the 
instruction manual of the corresponding laptop computer.
• Secure the screws on the connectors and tighten.
• Some computers may have multiple display screen modes. Use of some of these 
modes wi ll not be possible with this projector.
• For some RGB signal modes, the optional Mac adapter is necessary.
• When the image resolution is ch anged on a computer, depending on an input, 
automatic adjust function may take some time and may not be completed. In this case, 
you may not be able to see a check box to select “Yes/No” for the new resolution on 
Windows. Then the resolution will go back to the original. It might be recommended to 
use other CRT or LCD monitors to change the resolution.
About Plug-and-Play capability
Plug-and-Play is a system composed of the computer, its operating system and 
peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC 
2B. Plug-and-Play can be achieved by connecting this projector to computers that are 
VESA DDC (display data channel) compatible. 
• Please take advantage of this function by connecting the accessory RGB cable to the 
RGB IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other 
type of connection is attempted.
• Please use the standard drivers in your computer as this projector is a Plug-and-Play 
monitor. 
						

							
11
ENGLISH

Setting up
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL RGB IN2
RGB OUT
AUDIO IN2
AUDIO OUT
USBS-VIDEOCOMPONENT VIDEO
CB/PB
CR/PR
Y
VIDEO
AUDIO IN1
RGB IN1
CONTRO
L RGB IN2
RGB OU
T
AUDIO IN2
AUDIO OUT
USBS-VIDEOCOMPONENT VIDEO
CB/PB
CR/PR
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL RGB IN2
RGB OUT
AUDIO IN2
AUDIO OUT
USBS-VIDEOCOMPONENT VIDEO
CB/PB
CR/PR
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL RGB IN2
RGB OUT
AUDIO IN2
AUDIO OUT
USBS-VIDEOCOMPONENT VIDEO
CB/PB
CR/PRAudio outUSB(A)RS-232CRGB out
Examples of connection with a computer 
Connecting to a monitor (output)
Connecting to a speaker with amplifier (output)
RGB cable
Stereo mini 
audio cable 
* AUDIO IN1
 is linked to
 RGB IN1.
RGB outAudio out
Stereo mini 
audio cable 
RGB cable
RGB in
RGB cable
Audio in
Stereo mini 
audio cable 
USB 
cableRS-232C 
cable 
						

							
12

Setting up
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL RGB IN2
RGB OUT
AUDIO IN2
AUDIO OUT
USBS-VIDEOCOMPONENT VIDEO
CB/PB
CR/PR
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL RGB IN2
RGB OUT
AUDIO IN2
AUDIO OUT
USBS-VIDEOCOMPONENT VIDEO
CB/PB
CR/PR
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL RGB IN2
RGB OUT
AUDIO IN2
AUDIO OUT
USBS-VIDEOCOMPONENT VIDEO
CB/PB
CR/PR
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL RGB IN2
RGB OUT
AUDIO IN2
AUDIO OUT
USBS-VIDEOCOMPONENT VIDEO
CB/PB
CR/PR
Examples of connection with a VCR/DVD player
Audio outVideo out
Stereo mini audio cable 
Video cable 
Audio out
S-Video out
S-Video cable 
Stereo mini audio cable 
Stereo mini audio cable 
Audio out
Component video out
Component video cable 
Y
CB/PB
CR/PR
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL RGB IN2
RGB OUT
AUDIO IN2
AUDIO OUT
USBS-VIDEOCOMPONENT VIDEO
CB/PB
CR/PR
Stereo mini audio cable 
Audio out
Component video out
Component video cable 
Y
CB/PB
CR/PR 
						

							
13
ENGLISH

Setting up
Connecting power supply
WARNING  ►Please use extra caution when connecting the power cord as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact 
your dealer to newly get correct one.
• Only plug the power cord into an outlet rated for use with the power cord's 
specified voltage range.
• Never modify the power cord. Never attempt to defeat the ground connection 
of the three-pronged plug.
1. Connect the connector of the power cord to the 
AC inlet of the projector.
2. Firmly plug the power cord's plug into the outlet. 
AC inlet
Connectorof the power cord 
						

							
14

Remote control
Remote control
Putting batteries
WARNING  ►Always handle the batteries with care and use them only as 
directed. Improper use may result in battery explosion, cracking or leakage, 
which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of different 
types at the same time. Do not mix a new battery with used one. 
• Make sure the plus and minus terminals are correctly aligned when loading a 
battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
• Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry 
pla ce. 
•  If y ou observe a leakage of a battery, wipe out the flower and then replace 
a battery. If the flower adheres your body or clothes, rinse well with water 
immediately.
1. Remove the battery cover.  
Slide back and remove the battery cover in the direction of the arrow .
2. Insert the batteries. 
 Align and insert the two AA batteries according to their plus and minus   
terminals as indicated in the remote control.
3. Close the battery cover. 
 Replace the battery cover in the direction of the arrow and snap it back into 
place. 
						

							
15
ENGLISH

Remote control
Using the remote control
CAUTION  ►Be careful in handling the remote control.
• Do not drop or otherwise expose the remote control to physical impact.
• Do not get the remote control wet or place it on wet objects. Doing so may 
result in malfunction.
• Remove the batteries from the remote control and store them in a safe place if 
you won’t be using the remote control for an extended period. 
• Replace the batteries whenever the remote control starts to malfunction. 
• When strong lights, such as direct sunlight or light from an extremely close 
range (such as from an inverter fluorescent lamp), hit the projector’s remote 
sensor, the remote control may cause to function. Adjust the direction of the 
projector to keep light from directly hitting the projector’s remote sensor.
The remote control works with the projector’s remote sensor.
• The range of the remote sensor is 3 meters with a 60- degree range (30 degrees 
to the left and right of the remote sensor).
• Also a remote signal reflected in the screen etc. may be available. If it is difficult 
to send a remote signal to the sensor directly, please try.
•  Since  the  remote  control  uses  infrared  light  to  send  signals  to  the  projector 
(Class1  LED),  be  sure  to  use  the  remote  control  in  an  area  free  from  obstacles 
that could block the remote control’s output signal to the projector.
approx. 3 meters
30º30º 
						

							
16

Power on/off
Power on/off
WARNING  ►When the power is on, a strong light is emitted. Do not look 
into the lens or vents of the projector.
NOTE  •  Turn the power on/off in right order. Please power on the projector 
before the connected devices. Power off the projector after the connected devices.
Power switch
STANDBY/ON 
button
POWER indicator
Turning on the power
1. Make sure that the power cord is firmly and correctly 
connected to the projector and outlet.  
2. Open the lens cover, and set the power switch to the 
ON position.  
The power indicator will light to solid orange. Then wait 
several seconds because buttons may not function for 
these several seconds. 
3. Press the STANDBY/ON button on the projector or remote control.  
The projector lamp will light up and the POWER indicator will begin blinking 
green. When the power is completely on, the indicator will stop blinking light 
green.
To display the picture, select an input signal according to the section "Selecting an 
input signal" (17).
Turning off  the power
1. Press the STANDBY/ON button on the projector or 
remote control.  
The message "Power off?" will appear on the screen for 
approximately 5 seconds.
2. Press the STANDBY/ON button on the projector or 
remote control again while the message is visible. 
The projector lamp will go off, and the POWER indicator 
will begin blinking orange. 
Then the POWER indicator will stop blinking and light to 
solid orange when the lamp cooling is complete.
3. Make sure that th e power indicator lights to solid orange,  set the power switch 
to the OFF position. The POWER indicator will go off.  Close the lens cover. 
 Power off ?
POWER
(Solid orange)
POWER (Blinking green)
POWER
(Solid green)
POWER (Blinking orange)
POWER
(Solid orange)
STANDBY/O N INPUT
MENU
POWER T E M P L A M PVIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFFONMAGNIFYASPECT AUTOBLANKHOMEPAGE UPPAGE DOWNENDMUTEVOLUME
KEYSTONE
POSITION
ES
C ENTERMENU
RESET 
						

							
17
ENGLISH

Operating
Operating
Adjusting the volume
1. Press the VOLUME button on the remote control. 
A dialog will appear on the screen to aid you in adjusting 
the volume.
2. Use the cursor buttons ▲/▼ to adjust the volume.
To close the dialog and complete the operation, press the VOLUME button 
again. Even if you don’t do anything, the dialog will automatically disappear 
after a few seconds. 
VIDEORGBSEARCHST
ANDBY/ON
FREEZEOFFONMAGNIFYASPECT AUTOBLANKHOMEPAGE UPPAGE DOWNENDMUTEVOLUMEKEYSTONEPOSITION
ESC ENTERMENU
RESET
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFF
ONMAGNIFY
ASPECT AUTOBLANK
HOMEPAGE UP
PAGE DOWNENDMUTE
VOLUME
KEYSTONE
POSITION
ES
C ENTE
RMENU
RESE
T
Temporarily muting the sound
1. Press the MUTE button on the remote control.  
A dialog will appear on the screen  indicating that you have 
muted the sound. 
To 
restore the sound, press the MUTE or VOLUME button. 
Even if you don’t do anything, the dialog will automatically disappear after a few 
seconds.
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFFONMAGNIFYASPECT AUTOBLANKHOMEPAGE UPPAGE DOWNENDMUTEVOLUMEKEYSTONEPOSITION
ESC ENTERMENU
RESET
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFF
ONMAGNIFY
ASPECT AUTOBLANK
HOMEPAGE UP
PAGE DOWNENDMUTE
VOLUME
KEYSTONE
POSITION
ES
C ENTE
RMENU
RESE
T
Selecting an input signal
1. Press the INPUT button on the projector.  
Each time you press the button, the projector switches its 
input port as below.
RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO 
 
ST ANDBY/O N INPUT
MENUPOWER T E M P L A M P
1. Press the RGB button on the remote control to select an 
input port for RGB signal.  
Each time you press the button, the projector switches its 
RGB input port as below.
RGB IN1  RGB IN2
● When the TURN ON is selected to the item SEARCH of OPTION menu (36), 
the projector selects the RGB IN1 port at first. If no input is detected at the RGB 
IN1 port, projector will check the RGB IN2 port.
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFFONMAGNIFYASPECT AUTOBLANKHOMEPAGE UPPAGE DOWNENDMUTEVOLUMEKEYSTONEPOSITION
ESC ENTERMENU
RESET
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFF
ONMAGNIFY
ASPECT AUTOBLANK
HOMEPAGE UP
PAGE DOWNENDMUTE
VOLUME
KEYSTONE
POSITION
ES
C ENTE
RMENU
RESE
T1. Press the VIDEO button on the remote control to select 
an input port for video signal.  
Each time you press the button, the projector switches its 
video input port as below. 
COMPONENT VIDEO 
 S-VIDEO  VIDEO  
   
● When the TURN ON is selected to the item SEARCH of OPTION menu (36),  
the projector selects the COMPONENT VIDEO port at first. If no input is 
detected at the COMPONENT VIDEO port, projector will begin to check other 
ports. 
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFFONMAGNIFYASPECT AUTOBLANKHOMEPAGE UPPAGE DOWNENDMUTEVOLUMEKEYSTONEPOSITION
ESC ENTERMENU
RESET
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFF
ONMAGNIFY
ASPECT AUTOBLANK
HOMEPAGE UP
PAGE DOWNENDMUTE
VOLUME
KEYSTONE
POSITION
ES
C ENTE
RMENU
RESE
T 
						

							
18

Operating
Adjusting the zoom and focus
1. Use the zoom knob to adjust the screen size.  
2. Use the focus ring to focus the picture.
Searching an input signal
1. Press the SEARCH button on the remote control.   
The projector will begin to check its input ports in order to 
find any input signals. 
Then when an input is found, the projector will stop 
searching and display the image. If no signal is found, the projector will return 
to the state selected before the operation. 
RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO  
   
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFFONMAGNIFYASPECT AUTOBLANKHOMEPAGE UPPAGE DOWNENDMUTEVOLUMEKEYSTONEPOSITION
ESC ENTERMENU
RESET
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFF
ONMAGNIFY
ASPECT AUTOBLANK
HOMEPAGE UP
PAGE DOWNENDMUTE
VOLUME
KEYSTONE
POSITION
ES
C ENTE
RMENU
RESE
T
Selecting an aspect r atio
1. Press the ASPECT button on the remote control.   
Each time you press the button, the projector switches the mode for aspect 
ratio in turn. 
 At a RGB signal
NORMAL  4:3  16:9 
  
 At a video signal /no signal 
4:3  16:9  SMALL 
  
● The NORMAL mode keeps the original aspect ratio of the signal.
● At a HDTV signal of 1125i (1080i) or 750p (720p)  of COMPONENT VIDEO 
input, only 16:9 mode can be selected.
● Performing the automatic adjustment initializes the aspect ratio setting.
VIDEO
RGBSEARCHST
ANDBY/ON
FREEZEOFFONMAGNIFYASPECT AUTOBLANKHOMEPAGE UPPAGE DOWNENDMUTEVOLUMEKEYSTONEPOSITION
ESC ENTERMENU
RESET
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFF
ONMAGNIFY
ASPECT AUTOBLANK
HOMEPAGE UP
PAGE DOWNENDMUTE
VOLUME
KEYSTONE
POSITION
ES
C ENTE
RMENU
RESE
T
Zoom knobFocus ring 
						

							
19
ENGLISH

Operating
Correcting the keystone distortions
1. Press the KEYSTONE button on the remote control. 
A dialog will appear on the screen to aid you in
 correcting 
the distortion.
2. Use the cursor buttons ▲/▼ to correct the distortion.
To close the dialog and complete this operation, press the KEYSTONE button 
again. Even if you don’t do anything, the dialog will automatically disappear 
after a few seconds. 
● This function may not be work well with some input.
● The adjustable range for correcting will vary among inputs.
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFFONMAGNIFYASPECT AUTOBLANKHOMEPAGE UPPAGE DOWNENDMUTEVOLUMEKEYSTONEPOSITION
ESC ENTERMENU
RESET
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFF
ONMAGNIFY
ASPECT AUTOBLANK
HOMEPAGE UP
PAGE DOWNENDMUTE
VOLUME
KEYSTONE
POSITION
ES
C ENTE
RMENU
RESE
T
Using the  automatic adjustment feature
1. Press the  AUTO button on the remote control.  
 At a RGB signal 
The vertical position, the horizontal position, the clock 
phase and horizontal size will be automatically adjusted. 
Make sure that the application window is set to its maximum size prior to 
attempting to use this feature. A dark picture may still be incorrectly adjusted. 
Use a bright picture when adjusting.
 At a video signal 
The video format best suited for the respective input signal will be selected 
automatically.
 
This function is available only when the AUTO mode is selected to the item 
VIDEO FORMAT of the INPUT menu 
(30). For a component video signal, 
the signal type is identified automatically indep
endently of this function. 
●  The automatic adjustment operation requires approximately 10 seconds.  Also 
please note that it may not function correctly with some input.
VIDEO
RGBSEARCHST
ANDBY/ON
FREEZEOFFONMAGNIFYASPECT AUTOBLANKHOMEPAGE UPPAGE DOWNENDMUTEVOLUMEKEYSTONEPOSITION
ESC ENTERMENU
RESET
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFF
ONMAGNIFY
ASPECT AUTOBLANK
HOMEPAGE UP
PAGE DOWNENDMUTE
VOLUME
KEYSTONE
POSITION
ES
C ENTE
RMENU
RESE
T
Adjusting the position
1. Press the POSITION button on the remote control. 
The “POSITION” indication will appear on the screen.
2. Use the cursor buttons ▲/▼/◄/► to adjust the picture 
position.
When you want to reset the operation, press the RESET button on the remote 
control during the operation.
To complete this operation
, press the POSITION button again. Even if you don’t 
do anything, the dialog will automatically disappear after a few seconds.
● When this function is performed at a video signal, a certain extra such as a line 
may appear outside a picture.
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFFONMAGNIFYASPECT AUTOBLANKHOMEPAGE UPPAGE DOWNENDMUTEVOLUMEKEYSTONEPOSITION
ES
C ENTERMENU
RESET
VIDEO RGBSEARCHST
ANDBY/ON
FREEZEOFF
ONMAGNIFY
ASPECT AUTOBLANK
HOMEPAGE UP
PAGE DOWNENDMUTE
VOLUME
KEYSTONE
POSITION
ES
C ENTE
RMENU
RESE
T