Linksys Router BEFDSR41W User Manual

ADSL Gateway with Modem / Router / 4-Port Switch / Wireless-Ready
53
Instant Broadband
™Series
RIP Version
Select the version of IP you want to use.
• RIP-1Routing data will be sent in RIPv1 format.
• RIP-2BRouting data will be sent in RIPv2 format using subnet broadcast-
ing.
• RIP-2MRouting data will be sent in RIPv2 format using multicasting.
• N/ARouting data will not be sent.
Click the Show Routing Tablebutton to open a chart displaying how data is
routed through your LAN.
When f inished making your...

ADSL Gateway with Modem / Router / 4-Port Switch / Wireless-Ready
55
Instant Broadband
™Series
54
The DMZ Hosting function allows for a server attached to Port 4 of the
Gateway to be fully accessible from the Internet.  The Gateway supports an
Advanced form of DMZ, allowing the system attached to Port 4 to be on a
secure subnet, separate from the computers attached to the other 3 ports. 
Port 4 Status Selecting DMZ
enables the advanced DMZ
function for the switched Port
4. Selecting LANdisables the...

ADSL Gateway with Modem / Router / 4-Port Switch / Wireless-ReadyThe Link Test page allows an advanced user or technician to perform advanced
diagnostics of the ADSL Gateway and perform connectivity tests.
The information provided by these tests is not discussed in this document.
57
Instant Broadband
™Series
56
Link Test
Figure 6-25
Important:This is an Advanced Function.  No changes should be made
to this tab without a thorough understanding of network concepts.
The Firewall screen allows you to enable...

ADSL Gateway with Modem / Router / 4-Port Switch / Wireless-Ready
Make sure that you do NOT have a microf ilter plugged in between the
Gateway and the wall jack.  Verify that your ADSL account is active with
your ISP.
5. I can’t browse through the Gateway.
• Check if both ends of the network cable and power adapter are properly
connected. Check if the status LEDs on the front panel are functioning
properly. 
• If using Windows 95, 98 or Millennium, check the TCP/IP setup on the
client side. Run...

ADSL Gateway with Modem / Router / 4-Port Switch / Wireless-Ready
61
Instant Broadband
™Series
60
Iset up an Unreal Tournament Server, but others on the LAN cannot join. What do
I need to do?  If you have a dedicated Unreal Tournament server running, you
need to create a static IP for each of the LAN computers and forward ports
7777, 7778, 7779, 7780, 7781, and 27900 to the IP address of the server. You
can also use a port forwarding range of 7777 ~ 27900. If you want to use the
UT Server Admin, forward...

ADSL Gateway with Modem / Router / 4-Port Switch / Wireless-ReadyWhat are the Gateway’s advanced features?The Gateway’s advanced features
include Filters, Forwarding, Dynamic Routing, Static Routing, and DMZ
host.
Does Linksys provide syslog support?  No, Linksys does not currently provide
syslog support.
How can I check whether I have static or dynamic IP Addresses?Consult your
ISP to conf irm the information.
How do I get mIRC to work with the Gateway?Set port forwarding to 113 for the
computer on...

ADSL Gateway with Modem / Router / 4-Port Switch / Wireless-Ready
65
Instant Broadband
™Series
64
1. At the Wireless Screen, if you choose to enable WEP Encryption, select
Mandatoryunder the WEP section.
2. Press the WEP Key Settingbutton to set the WEP Encryption type and
level.
3. The following screen may appear, verifying that you are enabling WEP
Encryption.  Press the OKbutton to continue.
Figure B-2Figure B-1
Appendix B:Configuring
Wireless SecurityAn acronym for Wired Equivalent Privacy, WEP is an...

ADSL Gateway with Modem / Router / 4-Port Switch / Wireless-ReadyWEP Encryption key can be generated in one of two ways:
1. You may create an encryption key by using a Passphrase.
a. Enter a Passphrase, a user-def ined password, into the Passphrasef ield.
The Passphrase can be a maximum of 31 letters, symbols, and numbers.
No spaces can be used.
b. Click the Generatebutton to create a key. The key will be 10 digits if
you chose 64-bit encryption, or 26 digits if you chose 128-bit encryp-
tion. This key...

ADSL Gateway with Modem / Router / 4-Port Switch / Wireless-Ready2. In the “Control Panel” window, click the Network and Internet
Connectionsicon.
3. Click on the Network Connectionsicon.
4. The “Network Connections” window will appear.  Under LAN or High-
Speed Internet you will see all Network cards that are installed and operat-
ing in your computer. Double-click the Wireless Network Connection
icon associated with your wireless adapter.
If the “Wireless Network Connection Status” window appears,...

ADSL Gateway with Modem / Router / 4-Port Switch / Wireless-Ready
71
Instant Broadband
™Series
70
6. When the “Wireless Network Connection Properties” window appears,
click the Wireless NetworksTa b.
7. If the appropriate wireless network, specif ied by the Gateway’s SSID, is
displayed in the “Preferred networks” section, double-click it and continue
to the next step.
Otherwise, click on the appropriate wireless network, specif ied by the
Gateway’s SSID, in the “Available networks” section. Then, click...