Lucent Technologies Ds1/Cept1/Isdn Pri Reference Manual

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-77 G2.2 Administration 
6
Notes:
1. Trunk typ es p rec ed ed  with an asterisk (*) may b e selec ted  b y trunk typ e 
120 on an as need ed  Call-By-Call (CBC) Servic e Selec tion b asis.
2. Trunk typ es not inc lud ed  in these c ateg ories may not b e translated  for 
ISDN-PRI service. Most conventional trunk types specify, as a part of their 
name, an in/out sig naling sequenc e. Ac tually, these sig naling  seq uenc es 
are d isab led  and  typ e 20 sig naling is used  exc lusively over ISDN fac ilities.
3. Beg inning  with the 1.0 software load  of Generic  2 and  the 1.2 software 
load  of System 85 R2V4 d ig its may be inferred  when using  the 
ISDN-d ynamic  trunk typ e. The d efault of 30 infers DID (if nec essary). A 
d efault of 46 infers AAR/ARS.
Field 10
Used  as a d isp lay-only field. This field  d isp lays the trunk typ e that was 
ad ministered  in p roc ed ure 100, word  1.
Procedure 101 Word 1: ISDN Trunk Group, 
CDR, and Digital Loss Plan
Proc ed ure 101, word  1, is used  (p rimarily) to turn on CDR, as well as translate the 
digital loss plan.
Field 1
Disp lays the trunk g roup  numb er, suc h as p reviously translated  in p roc ed ure 
100.
Field 2
Assig ns whether the trunk g roup  has (1
) or d oes not have (0
) b alanc ed  
transmission fac ilities. Enc od e 1 is required  for ISDN-PRI.ISDN 120 (Note 3)
M/S TIE70 — 8
Sp ec ial 2, 5, 6, 50 — 58, 62, 65 — 67, 90 — 93
TIE 32 — 40, *41, *42, *43, 44, 45, *46, *47
WATS 26, *27, 28
Table 6-6. Trunks Supporting Signaling Type 20
Trunk Description Trunk Type 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-78 G2.2 Administration 
6
Field 3
Assig ns whether the trunk g roup  has (1
) or d oes not have (0
) the b attery reversal 
op tion. Enc od e 0 is required  for ISDN-PRI.
Field 4
Assig ns the numb er of p refix d igits. Field  enc od es and their d esc rip tions are:
Dash (–) is always ap p lic ab le for ISDN-PRI ap p lic ations exc ep t for DID trunks 
(trunk typ es 30 and 31).
Any sing le d ig it numb er (0 throug h 9).
The numb er is d etermined  b y the trunk g roup  and its ap p lic ation.
Field 5
Assig ns whether the trunk g roup  is (1
) or is not (0
) used  for DCS ap p lic ations.
Fields 6-7
This field  is ignored for ISDN ap p lic ations and  either enc ode (0 or 1) may b e 
translated.
Field 8
Assig ns or not assig n the trunk g roup to CDR rec ord  keep ing . Field  enc od es and  
their desc rip tions are:
Fields 9-11
Not used  for ISDN app lic ations.
Field 12
This field  is only ap p lic ab le when CDR is b eing  used , and  then only to c hang e 
the d efault CDR timer value. Field  enc odes rep resent intervals in 1-sec ond  
inc rements. The rang e is 1 throug h 99 with d ash (–) b eing  the d efault timer value 
of 6 sec ond s.0
Trunk g roup  usag e not ap p lic ab le for CDR rec ord ing .
1
Trunk g roup  usag e will b e rec ord ed  b y CDR.
2
Trunk g roup  usag e will b e rec ord ed , ac c ount c od e is req uired . 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-79 G2.2 Administration 
6
Field 13
Ad ministers the op tional transmission loss assig nments. The enc od e translated  
d epend s on the network c onfig uration and  servic e ap p lic ation. Field enc od es 
and  their c orresp ond ing  loss p lan are listed  as follows:
Fields 14-16
These field s are ig nored  b y ISDN software. Either enc od e (0 or 1) is satisfac tory.
Procedure 101 Word 3: Prefix Digits
This p roc ed ure allows you to p rep end  up  to four d ig its to the inc oming  c alled  
p arty numb er on a trunk g roup  b asis g iven the typ e of ad d ress in the c alled  p arty 
numb er. This p refixing  is d one before any dig it analysis is p erformed . You d o this 
b y entering  a typ e of ad d ress in field  2. This is the typ e of ad d ress field in the 
inc oming  c alled  p arty numb er IE. If you want c alls with this typ e of ad d ress to 
have digits prepended to the called party number digits, enter the desired digits 
in field s 3-6.
Procedure 103 Word 1: Network 
Trunk Group Translations
This p roc ed ure is used  to translate the trunk g roup network p arameters. Two 
sc reens are shown.
Field 1
Disp lays the trunk g roup  numb er, suc h as p reviously ad ministered in proc edure 
100 and  101.0
The Dig ital FIXED Loss Plan
1
ISL Tie Trunk
2
EIA Tie Trunk
This is the rec ommend ed  option for Sp eed ial Ac c ess Connec tions to a 
4ESS.
3
ISL Digital Central Offic e
4
EIA Dig ital Central Offic e
5
Dig ital Toll Offic e
6
Analog Toll Office
7
A U TO PL EX
® NETWORK Interfac e V
8
A U TO PL EX
® NETWORK Interfac e Y 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-80 G2.2 Administration 
6
Field 2
The ISDN-PRI d oes not p lac e any new or add itional c onsid erations on translating  
these field s. The enc od es that are translated  are g enerally d ep end ent on eac h 
trunk g roup , its ap p lic ation, and  the assoc iated  trunk g roups.
Field 3
Determines the numb er of traveling  c lass marks (TCMs) a trunk g roup  will send  
and receive. Encodes are:
Field 4
Used  to selec t (1
) or d isallow (0
) symmetric al routing .
Proc ed ure 285 field  5 is used  to ad minister the symmetric al routing  d ep th. If a 
c all enters the switc h on a trunk whic h has the network/tand em field s in 
p roc ed ure 103, word  1, set to 1,1 and  the symmetric al routing  d ep th field is set to 
a non-zero value, then the trunk g roup  is p art of a symmetric al route. After a 
p attern is selec ted , p referenc es for whic h the outg oing  trunk g roup  has the 
network/tand em field s in Proc ed ure 103 set to 1,1 and  for whic h the p referenc e 
numb er is g reater than the symmetric al routing  d ep th are ig nored .
If a c all enters the switc h on a trunk g roup that is p art of a symmetric al route (that 
is, p roc ed ure 103, word  1, field  4 is set to 1) and  the symmetric al routing  d ep th 
field  for the switc h is set to a non-zero value, then symmetric al routing  oc c urs. 
After a p attern is selec ted , p referenc es for whic h the outg oing  trunk g roup  has 
the symmetric al routing  field in Proc ed ure 103 set and for whic h the preferenc e 
numb er is g reater than the symmetric al routing  d ep th are ig nored .
Fields 5-8
The ISDN-PRI d oes not p lac e any new or add itional c onsid erations on translating  
these field s. The enc od es that are translated  are g enerally d ep end ent on eac h 
trunk g roup , its ap p lic ation, and  the assoc iated  trunk g roups.
Field 9
The digit sending index for a given preference (digit sending index field in 
p roc ed ure 318, word  1) and  Dial Tone Detec t Ignore field  for the trunk g roup 
(procedure 103, word 1, field 9) determine when digit sending begins. An 
outg oing  trunk seq uenc e is started after the outg oing  trunk is seized . If Dial Tone 
is d etec ted  d uring  the trunk seq uenc e, the switc h remembers the d etec tion. 0
Do not send  or exp ec t to rec eive any TCMs.
1
Send  or exp ec t to rec eive the FRL TCM.
2
Send  or exp ec t to rec eive the FRL and  c ond itional routing  TCMs. 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-81 G2.2 Administration 
6
When the trunk seq uenc e c omp letes, if Dial Tone was d etec ted and  the Dial 
Tone Detec t Ig nore field  for the trunk g roup  is set to 0, d ig it send ing  b eg ins 
immediately (the first pause is skipped).
If Dial Tone was not d etec ted  d uring  the trunk seq uenc e or the trunk g roup  is 
ad ministered  to Ignore Dial Tone, a timer is set b ased  on the p ause leng th of the 
first digit sending group. If the first pause is 0, digit sending begins immediately.
If Dial Tone is d etec ted  while p ausing  b efore send ing the first g roup and  Dial 
Tone Detec t Ig nore is set to 0, p ausing  is d isc ontinued  and  d igit send ing  b eg ins 
immediately. Otherwise, digit sending begins when Pausing completes.
Enc od es are:
Fields 10-12
The ISDN-PRI d oes not p lac e any new or add itional c onsid erations on translating  
these field s. The enc od es that are translated  are g enerally d ep end ent on eac h 
trunk g roup , its ap p lic ation, and  the assoc iated  trunk g roups.
Field 13
This field  affec ts how Network Digit Collec tion op erates and  when route selec tion 
is attempted  for network c alls arriving  on a trunk g roup . The d ifferenc es b etween 
the two op tions for this field  are easily illustrated  with a simp le examp le.
Supp ose a networks d ialing  p lan has b een ad ministered  in Proc ed ure 314 and  
that the p lan c onsists entirely of seven d igit ad d ress string s that are d ifferentiated  
b y their first three d ig its (i.e. they all have three d ig it string  id entifiers).
When a c all that arrives on a trunk g roup  for whic h this field  is zero enters 
Network Digit Analysis, an attemp t will b e mad e to c ollec t seven d ig its, and  any 
ap plic ab le traveling  c lass marks. Onc e these d ig its have b een c ollec ted , they 
are ap plied  to the networks d ialing  p lan, a Virtual Nod ep oint Id entifier is 
d etermined  and  route selec tion c ommenc es.
When a c all that arrives on a trunk g roup  for whic h this field is one enters Network 
Dig it Analysis, an attemp t will b e mad e to c ollec t three d igits. Sinc e all string s 
c an b e id entified  (and a Virtual Nod ep oint Id entifier d etermined ) b y the first three 
digits, a route could be selected after reception of the third digit. Whether or not 0
Dial Tone Detec tion Ac tive (d efault). If dial tone is d etec ted  d uring  the 
outgoing trunk sequence begin sending as soon as the sequence 
c omp letes (ig nore the first p ause sp ec ified in field  3 of p roc ed ure 321, 
word  2). If d ial tone is d etec ted during  the first p ause interval, b eg in 
send ing  immed iately.
1
Do not d o d ial tone detec tion, b eg in send ing  only after the p ause interval 
sp ec ified  in field  3 of p roc ed ure 321, word  2. 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-82 G2.2 Administration 
6
overlap p ed  sending  will oc c ur for the remainder of the seven dig it number 
d epend s on the op tion p rovisioned  in Field  14 of this word  for the trunk g roup 
referenc ed  in the selec ted  route. Please see Field  Help  for Field  14.
Setting  this field  to one c ould  ad versely affec t p roc essor oc c up anc y in hig h 
volume situations.
Setting  this field  for trunk g roup s whic h have ISDN sig naling  is inc onseq uential 
sinc e Network Dig it Analysis assumes that all d ig its whic h are to b e ap p lied  to 
the Network Dial Plan c an b e d isc erned from information c ontained  in the 
inc oming  Setup  messag e.
Enc od es are:
Field 14
If the route selec tion method  for the c alling  fac ility ind ic ates that route selec tion 
should  b e attemp ted  as soon as a Virtual Nod ep oint Identifier has b een 
d etermined  (field  13= 1) and  this field  is set to 1 for the trunk g roup  referenc ed  b y 
the c hosen route then overlap p ed  sending  will oc c ur for the remainder of the 
d ialed  numb er. This is the only means b y whic h overlap p ed send ing is 
ac c omp lished . Enc od es are:
Field 15
Su p p re s s D i a l  To n e
This field  is used  to sup p ress d ial tone after a WCR DAC is d ialed  or inferred  via 
p roc ed ure 101 Word  3.0
Commenc e route selec tion after entire numb er has been dialed .
1
Attempt route selection as soon as a Virtual Nodepoint Identifier has 
b een d etermined .
0
Collec t all dig its b efore send ing.
1
Overlap  send ing
0
Apply Dial Tone
1
Suppress Dial Tone 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-83 G2.2 Administration 
6
Procedure 116 Word 1: DS1/DMI/ISDN-PRI
Trunk Assignments
Eac h analog  trunk c irc uit p ac k p rovid es four c irc uits that are ad ministered  b y 
using  p roc ed ure 150. Conversely, eac h DS1 p rovid es 24 c irc uits (c hannels) that 
are ad ministered  b y using  p roc ed ure 116.
For trad itional mod ules, eac h DS1/MFAT c arrier will sup p ort a maximum of two 
DS1s, eac h oc c up ying  one slot and  loc ated  in slots 5 and 18. When a 
DS1/DMI/ISDN interfac e (trunk ap p lic ations) is loc ated in slot 5, it uses the six 
slots 0, 1, 2, 5, 6, and  7. When the interfac e is loc ated  in slot 18, it uses the six 
slots 13, 14, 15, 18, 19, and  20.
The DS1 c hannels are assig ned  to slot and  c irc uit loc ations ac c ord ing  to the 
ord er in whic h the mod ule p roc essor sc ans the equip ment c arrier as shown in 
Tab le 6-7
When the trad itional mod ule DS1/MFAT c arrier is c onfig ured  with two DS1s, 
p hysic al slots 3, 8, 16, and  21 are availab le for other ap plic ations. If only one DS1 
is c onfig ured , then six ad ditional slots are availab le for other app lic ations.
When the trad itional mod ule DS1-MFAT c arrier is c onfig ured  with two DS1s, 
p hysic al slots 3, 8, 16, and  21 are availab le for other ap plic ations. If only one DS1 
is c onfig ured , then six ad ditional slots are availab le for other app lic ations.Table 6-7. DS1/ISDN-PRI Administration — Channel 
vs.Trunk Assignments
DS1 Channel Slot/Circuit DS1 Channel Slot/Circuit
1 5/0 or 18/0 13 0/0 or 13/0
2 6/0 or 19/0 14 1/0 or 14/0
3 7/0 or 20/0 15 2/0 or 15/0
4 5/1 or 18/1 16 0/1 or 13/1
5 6/1 or 19/1 17 1/1 or 14/1
6 7/1 or 20/1 18 2/1 or 15/1
7 5/2 or 18/2 19 0/2 or 13/2
8 6/2 or 19/2 20 1/2 or 14/2
9 7/2 or 20/2 21 2/2 or 15/2
10 5/3 or 18/3 22 0/3 or 13/3
11 6/3 or 19/3 23 1/3 or 14/3
12 7/3 or 20/3 24 2/3 or 15/3 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-84 G2.2 Administration 
6
To minimize c onfusion and  eliminate the need  for maintaining  elab orate trunk to 
c hannel c ross-referenc e tab les, trunk group  memb er assig nments should  matc h 
the DS1 c hannel assig nments; for examp le, trunk g roup  memb er 1 on c hannel 1. 
For example, using  p roc ed ure 116, word  1, refer to Ta b l e  6 - 7
 to determine which 
slot and  c irc uit to translate for c hannel 1. Rep eat this p roc ed ure b y seq uentially 
selec ting  DS1 c hannels (2, 3, and  so on) and translating  the ap p ropriate slot and 
c irc uits as req uired .
Fields 1-5
These field s are used  to translate the eq uip ment loc ation, inc lud ing  slot and  
c irc uit (c hannel) loc ation, and to assoc iate the eq uip ment loc ation (c hannel) with 
the p artic ular trunk g roup  translated  in field  6.
Field 6
Translates the trunk g roup . Permitted  enc od es must b e numb ers with the rang e 
of 18 throug h 999.
Field 7
Translates a partic ular numb er that func tions as the nig ht servic e numb er. The 
d ig its d ep end  on the partic ular ap p lic ation and  its numb ering  p lan.
Field 8
Disab les a c hannels sig naling . This disab le func tion is req uired  for estab lishing  
a d ed ic ated  switc hed  c onnec tion. Field  enc od es and  their d esc rip tions are:
This option is only translated for the c hannels that is used  as a d ed ic ated  
switched connec tion. 
Field 9
Not ap p lic ab le for ISDN-PRI.
Field 10
Assig ns the func tion of the terminating  end p oint. For PRI nod al servic es, this 
endpoint is the network. Field encodes and their descriptions are:0
Sig naling  is enab led  (d efault value).
1
Signaling is disabled.
0
Another c ustomer p remises switc h
1
A p rivate network c onnec tion to a host c omp uter 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-85 G2.2 Administration 
6
Field 11
Translates the D-c hannel g roup  numb er. These numb ers should  b e c oord inated  
with field  1 of p roc ed ure 262, word  2. Field  enc odes and  their d esc rip tions are:
 Dash (–), for non-NFAS arrang ements.
Numb ers within the rang e 1 throug h 255 for all NFAS arrang ements.
Procedure 012 Word 1: Name Database
The name d atabase is used  b y those features (suc h as DCS, ISDN-PRI) whic h 
p rovid e d isp lay type information to voic e terminals. Some examp les of c ommon 
d isp lay information are: c alling  p arty name, vec tor d irec tory numb er, and  trunk 
g roup  name. For ISDN-PRI ap p lic ations, the name d atab ase information is used 
to p op ulate the d isp lay IE.
Field 1
Assig ns either an extension number, vec tor d irec tory numb er, or trunk g roup . 
Field encodes and their descriptions are:
000 throug h 99999, for extension and d irec tory numb ers.
Whether the numb er is three, four, or five d ig its d ep end s on the numb ering  p lan.
18 throug h 999, for trunk g roup  numbers.
Field 2
Sp ec ifies whether the enc ode for field  1 is a trunk g roup  or extension/vec tor 
directory number. Field encodes and their descriptions are:
Field 3
This field  is only ap p lic ab le for the id entified  extensions d isp lay mod ule. It 
c ontrols the numb er of b lank sp ac es that are inserted before the first d isp layed  
c harac ter of the name, d ialed  numb er, or trunk g roup  name. Permitted  enc od es 
are numbers from 1 to 30.2
Pub lic  network c onnec tions
0
Tr u n k  g r o u p s
1
Extension numb ers and  vec tor d irec tory numb ers 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-86 G2.2 Administration 
6
Field 4
The main func tion of this field  is to provid e some ad ministration c ontrol over what 
is displayed on the voice terminals digital display. Field encodes and their 
descriptions are:
Field 5
Assig ns the method  used  to d efine the name. Field  enc od es and  their 
descriptions are:
Field 6
This field  is used  with field  5 to c op y an existing  name to the extension or trunk 
g roup  id entified  in field  1. Field  enc od es and  their desc rip tions are:
000 throug h 99999, for extension and  d irec tory numb ers. Whether the numb er is 
three, four, or five d ig its d ep end s on the numbering  p lan.
18 throug h 999, for trunk g roup  numbers.
Procedure 012 Word 2: Name Database
This word  is used to translate a name (up  to a maximum of 30 c harac ters).
Field 1
Identifies one-of-three 10 c harac ter field s. Field  enc od es and  their d esc riptions 
are:–
(Dash) all inc oming  only trunk g roup s
0
The user (extension) d oes not want the outg oing  trunk g roup  name 
d isp layed  b ut d oes desire the dialed  numb er to remain on the d isp lay.
1
The user d esires to display the name of the outg oing  trunk g roup  (for 
examp le, ISDN/SDN, MEGACOM, CBC).
For a tand em interworking  c all the name of the inc oming  trunk g roup is 
transmitted  in the d isp lay IE of the ISDN-PRI outg oing  trunk g roup.
0
Add  a new name or c hang e an existing  name; req uires that the name 
c hang e b e mad e with word  2
1
Cop y the name from the extension or trunk g roup  d isp layed  in field  6
1
Charac ters 1 throug h 10
2
Charac ters 11 throug h 20