Makita Cordless or Electric Jobsite Radio User Manual

Radio Instruction manual
Radio Manuel d’instructions
Radio  Manual de instrucciones
BMR100 

2
PM
1
5
94
6
7
8 23
1012
14
13
11
A
B
C
D
E
LK
J
I
H
G
F 

3
12
34
56
1114
15
15
16
1817
19
19
10
8
9 

4
Li-ion
Symbols
The following show the symbols used for the equipment. Be sure that you understand their meaning before use.
Symboles
Nous donnons ci-dessous les symboles utilisés pour l’appareil. Assurez-vous que vous en avez bien compris la 
signification avant d’utiliser l’outil.
Símbolos
A continuación se muestran los símbolos utilizados para el equipo. Asegúrese de que entiende su significado
antes de usarla.
❏ Read instruction manual.❏ Lire le mode d’emploi.❏ Lea el manual de instrucciones.
❏...

5
ENGLISH
IMPORTANT SAFETY 
INSTRUCTIONS
WARNING:
When using electric tools, basic safety precautions should 
always be followed to reduce the risk of fire, electric 
shock, and personal injury, including the following:
1. Read this instruction manual and the charger 
instruction manual carefully before use.
2. Clean only with dry cloth.
3. Do not block any ventilation opening. Install in 
accordance with the manufacturer’s instruction.
4. Do not install near any heat sources such as radiators, 
heat...

6
Battery Installation 
Note:
Keeping back up batteries inside the compartment 
prevent stored data in preset memories from being lost.
1.Pull out the battery compartment locker to release 
battery compartment. There are main battery pack 
compartment and back up battery compartment. 
(Fig.1 & 2)
2.Remove back up battery compartment cover and 
insert 2 fresh UM-3 (AA sizes). Make sure the 
batteries are with correct polarity as shown inside the 
compartment. Replace the battery cover.
3.After back up...

7 2.Select the required waveband by pressing the Band 
button. Make sure the rubber bended rod antenna has 
been well placed for best FM reception. For AM (MW) 
band, rotate the radio to get best signal. Try to avoid to 
operate the radio next to computer screen and other 
equipment which will cause interference to the radio.
3.Press and release Scan button (long press Scan 
button more than 2 seconds will activate time setting), 
LCD display will flash Scan symbol and the radio will 
up search and stop...

8 1.The HWS buzzer alarm can be set either radio is on or 
off.
2.Press and release the HWS buzzer alarm button 
, the symbol will flash.
3.During the symbol flashes, long pressing the   
button for more than 2 seconds followed by a beep 
and display Hour digit will flash.
4.Rotate Tuning Control to select required alarm hour, 
then press    time set button   again. The minute digit 
will then flash.
5.Rotate Tuning Control to select required alarm minute, 
the press time set button   again to complete...

9
FRANÇAIS
CONSIGNES DE SÉCURITÉ 
IMPORTANTES
AVERTISSEMENT :
Lors de l’utilisation des outils électriques, vous devez 
toujours prendre des précautions élémentaires en matière 
de sécurité pour réduire les risques d’incendie, de choc 
électrique et de blessure. Ces précautions comprennent 
les suivantes :
1. Avant l’utilisation, lisez attentivement le manuel 
d’instructions de l’outil et celui du chargeur.
2. Ne l’essuyez qu’avec un chiffon sec.
3. Évitez de bloquer les orifices de ventilation. Exécutez...

10 2.Enlever le couvercle du compartiment des batteries 
supplémentaires et insérer 2 Batteries UM-3 
(Dimension AA). Vérifier que les batteries sont 
installées en polarité de facon correcte comme 
indiqué dans le boitier. Remettre le couvercle.
3.Après avoir introduit les batteries supplémentaires. 
Mettre les batteries principales dans la radio. Liste ci-
dessous des batteries compatibles pour cette radio.
Batterie pod : 
9,6V:  9135 | 9134 | 9122 | PA09 | 9120 
12V:  1235 | 1234 | 1222 | PA12 | 1220...