Midway Sportstation 25in Conversion Kit Operation Manual

Assembly          1-9
A
AA
A B
BB
B
PLAYER PANEL BUTTONS
31-3476
31-176831-3483
31-3484
31-3586
31-3587
31-358731-3476
TYPICAL DECAL MOUNTING DETAILS 

Assembly          1-10
INSTALL PLAYER CONTROLS
NOTICE: This isn’t an actual-size drawing. Use the template to help you position and
drill mounting holes. Don’t attempt to substitute this drawing for the template.
16-10830
40.75+.031
-.000
13.50+.031
-.000
PLAYER PANEL TEMPLATE 16-10830
[ ] 1.  If  you’re assembling both kit 15909 and optional player panel 45494, skip to Step 19. If you’re
assembling just kit 15909, proceed with the next step.
[ ] 2.  Locate and unfold the player panel template....

Assembly          1-11 
[ ] 5.  Place the player panel face down on top of the clear plastic cover. Center the player panel. Mark
the outside shape of the panel on the cover. Also mark hole locations. Remove the player panel
and set it aside. Cut and deburr holes for player panel buttons. Trim the cover to panel shape.
[ ] 6.  Lightly moisten the cabinet with soapy water. Remove the backing from the wallpaper decal.
Apply the decal to the player panel. Start at the top and work down. After you’ve...

Assembly          1-12
A-21939-1
20-10209-3 20-10209-220-10209-7
20-10209-1
TYPICAL MODIFIED PLAYER PANEL
04-11089
TYPICAL PLAYER PANEL HOUSING
TYPICAL COMPLETED CABINET 

Assembly          1-13
INSTALL ELECTRONICS TRAY COMPONENTS
CAUTION: Board set electronic components are static sensitive. Prepare an anti-static
work area. Ground yourself before removing circuit boards from their protective
shipping materials.
WARNING: Don’t connect cables to the circuit boards or power supply when the power
is on. Otherwise, you’ll damage VGM electronics and void your warranty.
CAUTION: Hard disk drives are fragile. Don’t stack or drop hard disk drives.
NOTICE: If your monitor requires...

Assembly          1-14
TYPICAL ELECTRONICS LAYOUT
WIRE THE 
CIRCUIT BOARDS
 
NOTICE: 
You must install the Main (JAMMA) Wiring Harness supplied with this
conversion kit. This VGM’s 49-way joysticks require wires and circuits not found in
earlier VGMs. If the connectors in your cabinet don’t fit onto the CPU Board or wire
colors don’t match the JAMMA Chart, contact your authorized distributor for
assistance.
CAUTION: 
Insulate unused wires within the JAMMA cable, especially red, yellow,
orange and black...

Assembly          1-15 [ ] 2.  Locate disk drive power cable H-22900.2. (This cable has separate wires and plastic connectors
at each end). Attach the power cable to SIO connector P3 (near a large heatsink). Mate the plug
and jack. Press them firmly to seat contacts. The connector is keyed. Don’t use excessive force.
[ ] 3.  The disk drive power cable includes three plugs for the fans. Connect these plugs to the fans.
[ ] 4.  Secure hard disk drive and fan cables with three cable clamps from the kit....

Assembly          1-16 [ ] 6.  Locate the data and power connectors on the hard drive. Connect the free end of the hard drive
power cable to the disk drive. Mate the plug and jack. Press them firmly to seat contacts. Don’t
use excessive force.
[ ] 7.  Position the striped edge of the hard drive data cable by the power cable. Attach the cable to the
drive’s data connector. The data connector is keyed. Don’t use excessive force.
WIRE THE 
CABINET
Kit 15909, Without Optional Player Panel 45494…
NOTICE: This...

Assembly          1-17 [ ] 7.  Locate the square, split ferrite bead. The
factory has installed one ferrite bead around
DC power conductors (solid color heavy
gauge wires with pin numbers 1-6 or A-F). A
second bead encircles player panel
conductors (striped color lighter gauge
wires). Install the remaining ferrite beads on
the video monitor cable and power supply
wires. The video cable bead should trap a
loop of cable. Place all beads as close to the
JAMMA connector as possible. Then close
and lock each...

Assembly          1-18
CHECK YOUR CABLING JOB
[ ] 1.  Carefully inspect cables between peripherals and the board set. The main wiring harness edge
connector (JAMMA) attaches to the SIO Board.
[ ] 2.  The hard drive data (ribbon) cable connects the hard drive to CPU Board jack P5. Be sure that
you’ve also connected the hard drive power connector to power cable H-22900.2. The other end
of this cable should connect to the SIO Board at P3.
CABLE BLOCK DIAGRAM