Miele G 1262 Scvi Operating Instructions

Options
With the Options button the functions
Turbo and Tab can be selected.
Open the door.
Turn the dishwasher on .
Theindicator lights up.
Press and hold the Options button
until the indicator of the desired
function lights up.
The option will remain active for all
programs until the setting is changed
again.
A program can now be started as
usual or the dishwasher can be
turned off .
Turbo
The Turbo function can be used to
reduce the program run-times, in
programs in which the option is...

Delay start
The starting time of a program can be
delayed. The start time can be delayed
from 30 minutes to 24 hours.
With a delay start time between 30
minutes and 9 hours 30 minutes the
delay is set in 30 minute increments.
For 10 hours or more it is set in one
hour increments.
When using the Delay Start
function, make sure that the
detergent compartment is dry before
adding detergent. Wipe dry with a
cloth if necessary. Otherwise the
detergent could stick together and
not completely rinse out.
Gel...

Buzzer
A signal sounds at the end of a
program and when a fault occurs.
The buzzer at the end of a program
sounds five times in quick succession
for up to one hour.
The buzzer for a fault sounds in
intervals up to two minutes.
The buzzer is activated by default. It
can be turned off, so it does not sound
at the end of a program. The buzzer for
a fault cannot be turned off.
Open the door.
Turn the dishwasher off with .
Press the Program button and at the
same time turn the dishwasher on
with .
Hold...

With the aid of the following guide, minor problems can be fixed without a service call.
Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Technical faults
Problem Possible fault Solution
The program does not
start.The door is not
properly closed.Close the door firmly.
The machine is not
plugged in.Insert the plug.
The fuse is defective
or the breaker has...

Problem Possible fault Solution
The optical indicator
flashes.
The buzzer sounds.
All program indicators
are flashing fast when
the door is open.
The time display shows
FXX.There may be a
technical fault.Turn the dishwasher off .
After a few seconds:
–Turn the dishwasher on.
–Select the desired program
with the program button.
–Close the door.
If the problem persists contact
Technical Service.
The drain pump is
running when the door
is opened.Fault F70: The
waterproof system
has activated.–Turn off the...

Problems water intake/drain
Problem Possible fault Solution
The optical indicator
flashes.
The buzzer sounds.
The Intake / Drain
indicator flashes when the
door is open.The water supply
is shut off.–Open the water supply.
The dishwasher stops.
The optical indicator
flashes.
The buzzer sounds.
The Intake / Drain
indicator flashes when the
door is open.
The time display shows
FXX.Before fixing the fault:
–Turn the dishwasher off .
Fault F12/F13:
Water intake fault–Open the water supply.
–Clean the water...

General problems with the dishwasher
Problem Possible fault Solution
The display turns off.The dishwasher has gone
into Standby mode to
save energy.Press any button.
The display turns on again.
Detergent is left in the
dispenser at the end
of a program.The dispenser was damp
when detergent was
added.Dry the dispenser before
adding detergent.
The detergent lid
cannot be closed
properly.Detergent residue is
blocking the catch.Remove the residue.
The door and the
interior walls are still
wet after a...

Sounds
Problem Possible fault Solution
There is a knocking
noise in the wash
cabinet.The spray arm is hitting an
item in the basket.Interrupt the program,
rearrange items blocking
the spray arms.
There is a rattling
noise in the wash
cabinet.Items are not secure in the
wash cabinet.Interrupt the program and
rearrange loose pieces.
There is a knocking
noise in the water
pipes.This may be caused by the
installation or the diameter
of the pipe.This has no effect on the
dishwasher. If in doubt
contact a...

Poor cleaning results
Problem Possible fault Solution
The dishes are not
clean.The dishes were not loaded
correctly.See Loading the
dishwasher.
The program was not
powerful enough.Select a more intensive
program, see Program
Guide.
Not enough detergent was
dispensed.Use more detergent, see
Adding detergent.
The spray arms are blocked
by items.Turn the spray arm and
rearrange the dishes if
necessary.
The triple filter is clogged or
not correctly inserted. The
spray arm jets may be
clogged.Clean the filter...

Problem Possible fault Solution
Dishes are not dry,
glasses and cutlery
are spotted.The rinse aid setting may be
too low, or the rinse aid
reservoir is empty.Increase the dosage, refill
the reservoir or switch the
rinse aid product when
refilling, see Before using
for the first time.
Dishes were taken out too
soon.Leave dishes in longer, see
Use.
A Tab product was used.
These products have a low
drying effect.Set the Detergent setting for
a normal detergent and add
rinse aid.
The Tab option is turned
on,...