Miele G 1262 Scvi Operating Instructions

							Options
With the Options button the functions
Turbo and Tab can be selected.
Open the door.
Turn the dishwasher on .
Theindicator lights up.
Press and hold the Options button
until the indicator of the desired
function lights up.
The option will remain active for all
programs until the setting is changed
again.
A program can now be started as
usual or the dishwasher can be
turned off .
Turbo
The Turbo function can be used to
reduce the program run-times, in
programs in which the option is
available.
Using the Turbo option during the
Express program will rinse the dishes
without heat, e.g. to avoid smells, if a
complete program is not yet needed.
Tab
To achieve the best results, the
dishwasher can be programmed for the
type of detergent being used. The
Options button can be used to select
between normal detergents (powder or
gel ) and tabs.
The program sequence is adapted to
the selected detergent type.
Depending on the program selected
the run-time may be extended
considerably.
If the Tab indicator is not lit, the
dishwasher is set for normal detergent.
If the Tab indicator is lit than the
program sequence is adapted to suit
detergents than contain rinse aid (as
well as other components where
applicable).
The rinse aid dispenser and indicator
light are deactivated.
Follow the instructions of the detergent
manufacturer.
The cleaning and drying
performance of normal detergents
versus tabs varies greatly.
Additional options
31
 
						

							Delay start
The starting time of a program can be
delayed. The start time can be delayed
from 30 minutes to 24 hours.
With a delay start time between 30
minutes and 9 hours 30 minutes the
delay is set in 30 minute increments.
For 10 hours or more it is set in one
hour increments.
When using the Delay Start
function, make sure that the
detergent compartment is dry before
adding detergent. Wipe dry with a
cloth if necessary. Otherwise the
detergent could stick together and
not completely rinse out.
Gel detergent should not be used
when selecting Delay Start, the
detergent could leak out of the
compartment.
Open the door.
Turn the dishwasher on .
The indicator  lights.

Select the desired program with the
Program button.

Press the  button.
The last set delay start time will show in
the time display. The indicator 
lights.

Set the desired delay start time with
the  button.
If you press and hold the  button the
time with automatically count up to24^.
To start again at 30 minutes, press the
 button twice.

Close the door.The time will count down to the
program start: in 1-hour-steps over
10 hours, in 1-minute-steps under
10 hours.
Once the delay start time has elapsed,
the selected program starts. The
display shows the remaining time, the
indicator  goes out and the indicator
of the selected program lights.
Delay start display
Up to 59 minutes: e.g. 30 minutes =30
Between1hand9h30min:
e.g. 5 hours =5.00
10 hours and over: e.g. 15 h =15^
Starting a program before the delay
start has elapsed
A program can be started before the
delay start time has elapsed.
Open the door.
Press the  button.

Press the  button.

Select the desired program with the
Program button.

Close the door.
The optical control lights. The program
begins.
Additional options
32
 
						

							Buzzer
A signal sounds at the end of a
program and when a fault occurs.
The buzzer at the end of a program
sounds five times in quick succession
for up to one hour.
The buzzer for a fault sounds in
intervals up to two minutes.
The buzzer is activated by default. It
can be turned off, so it does not sound
at the end of a program. The buzzer for
a fault cannot be turned off.
Open the door.
Turn the dishwasher off with .
Press the Program button and at the
same time turn the dishwasher on
with .
Hold the program button until the
lower right program indicator comes
on.
If it does not come on, start over.

Press the Options button four times.
The Tab indicator flashes four times in
intervals.
The time display shows if the program
end buzzer is turned on or off.
–
p1: Buzzer is turned on
–
p0: Buzzer is turned off

Press the Program button to change
the setting.
The setting is saved.

Turn the dishwasher off with .
Default settings
All settings can be reset to the factory
default.
Open the door.
Turn the dishwasher off .
Press and hold the Program button
and at the same time turn the
dishwasher on . Hold the Program
button until the lower right program
indicator comes on.
If it does not come on, start over.
Press the Options button 12 times.
The Tab indicator flashes once long
and twice short in intervals.
The time display shows if a setting was
changed.
–p1: All settings are factory default.
–p0: At least one setting was
changed.
To reset the dishwasher to the factory
default, press the Program button.
The setting is saved.

Turn the dishwasher off .
Additional options
33
 
						

							With the aid of the following guide, minor problems can be fixed without a service call.
Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Technical faults
Problem Possible fault Solution
The program does not
start.The door is not
properly closed.Close the door firmly.
The machine is not
plugged in.Insert the plug.
The fuse is defective
or the breaker has
tripped.Reset the circuit breaker.
See data plate for minimum
amperage.
The dishwasher is
not turned on.Turn the dishwasher on 
and select a program.
The dishwasher stops
during a program.The fuse has
tripped.Reset the circuit breaker.
See data plate for minimum
amperage.
The optical indicator is not
visible when a program
has started.The reflector was
not properly
installed.Install the reflector properly,
see the separate Installation
sheet.
Frequently asked questions
34
 
						

							Problem Possible fault Solution
The optical indicator
flashes.
The buzzer sounds.
All program indicators
are flashing fast when
the door is open.
The time display shows
FXX.There may be a
technical fault.Turn the dishwasher off .
After a few seconds:
–Turn the dishwasher on.
–Select the desired program
with the program button.
–Close the door.
If the problem persists contact
Technical Service.
The drain pump is
running when the door
is opened.Fault F70: The
waterproof system
has activated.–Turn off the water supply.
–Contact Miele Technical
Service.
Frequently asked questions
35
 
						

							Problems water intake/drain
Problem Possible fault Solution
The optical indicator
flashes.
The buzzer sounds.
The Intake / Drain
indicator flashes when the
door is open.The water supply
is shut off.–Open the water supply.
The dishwasher stops.
The optical indicator
flashes.
The buzzer sounds.
The Intake / Drain
indicator flashes when the
door is open.
The time display shows
FXX.Before fixing the fault:
–Turn the dishwasher off .
Fault F12/F13:
Water intake fault–Open the water supply.
–Clean the water intake filter,
see User Maintenance
Instructions.
– The water pressure at the
water connection is lower
than 4.35 psi.
Consult a plumber.
Fault F11: Water
drain fault.
There may be
water in the wash
cabinet.See User Maintenance
Instructions.
– Clean the triple filter.
–
Clean the drain pump and the
non-return valve.
–
Remove any kinks in the drain
hose.
Frequently asked questions
36
 
						

							General problems with the dishwasher
Problem Possible fault Solution
The display turns off.The dishwasher has gone
into Standby mode to
save energy.Press any button.
The display turns on again.
Detergent is left in the
dispenser at the end
of a program.The dispenser was damp
when detergent was
added.Dry the dispenser before
adding detergent.
The detergent lid
cannot be closed
properly.Detergent residue is
blocking the catch.Remove the residue.
The door and the
interior walls are still
wet after a program
has finished.This is not a fault! It is the
normal operating mode of
the drying system.The moisture will evaporate
after a short time.
Water remains in the
wash cabinet at the
end of a program.Before fixing the fault:
– Turn the dishwasher off
.
The triple filter in the wash
cabinet is clogged.Clean the triple filter. See
User Maintenance
Instructions.
The drain pump or the
non-return valve may be
blocked.Clean the drain pump and
the non-return valve, see
User Maintenance
Instructions.
The drain hose is kinked. Remove any kinks from the
drain hose.
Frequently asked questions
37
 
						

							Sounds
Problem Possible fault Solution
There is a knocking
noise in the wash
cabinet.The spray arm is hitting an
item in the basket.Interrupt the program,
rearrange items blocking
the spray arms.
There is a rattling
noise in the wash
cabinet.Items are not secure in the
wash cabinet.Interrupt the program and
rearrange loose pieces.
There is a knocking
noise in the water
pipes.This may be caused by the
installation or the diameter
of the pipe.This has no effect on the
dishwasher. If in doubt
contact a plumber.
Frequently asked questions
38
 
						

							Poor cleaning results
Problem Possible fault Solution
The dishes are not
clean.The dishes were not loaded
correctly.See Loading the
dishwasher.
The program was not
powerful enough.Select a more intensive
program, see Program
Guide.
Not enough detergent was
dispensed.Use more detergent, see
Adding detergent.
The spray arms are blocked
by items.Turn the spray arm and
rearrange the dishes if
necessary.
The triple filter is clogged or
not correctly inserted. The
spray arm jets may be
clogged.Clean the filter and insert
the filter correctly, see User
Maintenance Instructions.
The drain pump or the
non-return valve is blocked.
Wash water will run back
into the wash cabinet.Clean the drain pump and
the non-return valve, see
User Maintenance
Instructions.
Glasses and cutlery
show streaks. There
is a bluish sheen on
the surface of
glasses and film that
can be wiped off.The rinse aid dosage is set
too high.Reduce the dosage, see
Before using for the first
time.
Frequently asked questions
39
 
						

							Problem Possible fault Solution
Dishes are not dry,
glasses and cutlery
are spotted.The rinse aid setting may be
too low, or the rinse aid
reservoir is empty.Increase the dosage, refill
the reservoir or switch the
rinse aid product when
refilling, see Before using
for the first time.
Dishes were taken out too
soon.Leave dishes in longer, see
Use.
A Tab product was used.
These products have a low
drying effect.Set the Detergent setting for
a normal detergent and add
rinse aid.
The Tab option is turned
on, but a normal product
was used.Set the Detergent setting to
the detergent used, see
Additional options - Tab.
White residue is
visible on cutlery
and dishes.
Clouding occurs on
glassware and film
can be wiped off.Not enough rinse aid was
used.Increase the dosage, see
Before using for the first
time.
Unsuitable Tab products
were used.Change detergent, use
normal tabs or normal
powder detergent.
The salt container is empty
(depending on model).Refill the salt container, see
Before using for the first
time.
The salt container lid was
not correctly screwed on
(depending on model).Reseat the lid making sure ir
screws back on correctly.
Frequently asked questions
40