Miele G 1262 Scvi Operating Instructions

							Cleaning the water inlet filter
A filter is incorporated into the intake
hose attached to the dishwasher’s shut
off valve. If your water is hard or the
pipes contain sediment, this filter may
clog and prevent enough water from
entering the wash cabinet.
The plastic housing of the water
connection contains electrical
wiring.
Do not cut the intake hose or
submerge it in liquid.
Installing an in-line water filter
If your water contains a large number of
insoluble substances, a filter between
the water valve and the intake hose
connection is recommended. These
filters can be purchased from Miele.
Cleaning the filter
Turn off the dishwasher and pull the
plug.

Turn off the water supply.

Unscrew the intake hose.Carefully remove the rubber seal.
Remove the filter using needle nose
pliers and rinse it under running
water.
Reinsert the filter and seal. Make sure
they are seated correctly.
Screw the intake hose back on the
water valve, checking that it is not
cross-threaded.

Slowly turn on the water supply and
test for leaks.
Cleaning and Care
51
 
						

							Cleaning the drain pump and
non-return valve
If the dishwasher is not completely
drained at the end of a program, the
drain pump or non-return valve may be
blocked.
Turn off the dishwasher and pull the
plug.
Remove the triple filter (see Triple
filter system).
Use a cup or bowl to scoop water out
of the wash cabinet.

Tilt the locking clamp to the side.

Pull out the non-return valveand
rinse it under running water.

Remove all foreign objects from the
non-return valve.The drain pump is beneath the
non-return valve (see arrow).
Remove all foreign objects from the
drain pump (glass or bone splinters).
Before returning the non-return valve,
check that the drain pump is not
blocked. Spin the propeller several
times in both directions to check for
obstructions.
Carefully reinsert the non-return valve
and secure it with the locking clamp.
Make sure the locking clamp
clicks into place!
Cleaning and Care
52
 
						

							Installation Instructions
Please refer to the Installation Diagram supplied with these instructions.
To comply with IEC sound testing protocols, please contact Miele for additional
instructions.
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
 
						

							Disposal of the packing
material
The cardboard box and packaging
protect the appliance during shipping.
These materials are biodegradable and
recyclable. Please recycle.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
Disposal of an old machine
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Ensure that the appliance presents no
danger to children while being stored
for disposal. Before discarding an old
appliance, unplug it from the outlet, cut
off its power cord and remove any
doors to prevent hazards.
Help to protect the environment
54
 
						

							Installation, repairs and other
work by unqualified persons could
be dangerous.
Check that the voltage, frequency
and fuse rating shown on the data
plate match the household mains
supply.
The power outlet must be accessible
after installation. Do not use an
extension cord to connect the
dishwasher to the mains. Danger of
overheating! See data plate on the
right side of the door.
A damaged power cord must only
be replaced with a genuine Miele
cord by a Miele service technician.
GROUNDING INSTRUCTIONS
THIS APPLIANCE MUST BE
GROUNDED.
In the event of a malfunction or
breakdown, grounding will reduce the
risk of electric shock by providing a
path of least resistance for the electrical
current. This appliance is equipped
with a cord having an equipment
grounding conductor and a grounding
plug. The plug must be plugged into an
appropriate outlet that is installed and
grounded in accordance with all local
codes and ordinances.
Improper connection of the
equipment grounding conductor
can result in electric shock. Do
not modify the plug provided with
the appliance; if it will not fit the
outlet, have a proper outlet
installed by a qualified electrician.
If there is any question
concerning the proper electrical
connection or grounding of this
appliance to the power supply,
please consult a licensed
electrician or call Miele’s
Technical Service Department:
1-800-999-1360
1-800-565-6435
Specifications
The dishwasher comes equipped with a
4 ft (1.2 m) power cord with a molded
plug for connection to 120 V, 60 Hz,
15 A grounded receptacle.
Electrical connection
55
 
						

							
Waterproof system
All Miele dishwashers have a safety
valve located on the incoming water
line and a sealed underside with a
water sensor. If a fault occurs, the water
intake is stopped and the drain pump is
activated.
Connection to the water
supply
Do not drink water from the
dishwasher!
– The dishwasher can heat its own water to the temperature required by
the wash program. This allows for
connection of the machine to either a
hot or cold water source. For lowest
energy consumption connect the
dishwasher to a cold water source.
For fastest possible wash times, with
slightly higher energy consumption,
connect the dishwasher to a hot
water source. All programs use hot
water in the rinse cycles.
– The inlet hose is approximately 5 ft.
(1.5m) long.
– A 5 ft. (1.5m) drain extension is
available from Miele.
– The water inlet hose comes
equipped with a 3/4 female hose
thread connector. This can be
directly connected to a water supply
with 3/4 MHT (male hose thread
ends).
– Water pressure: Must be between
4.5 - 145 psi (0.3 - 10 bar).
To prevent damage to the
dishwasher, it must only be
connected to a fully vented drainage
system.
Do not cut the intake hose. It
contains electrical wiring. If the hose
is cut, the dishwasher will not work.
There will be a water leak and you
could be injured. If the hose is too
long, coil it neatly and place it
behind the machine.
Plumbing
56
 
						

							Drainage
–The machine comes equipped with a
built-in non-return valve on the
discharge side to prevent waste
water from flowing back into the
dishwasher.
–The dishwasher is equipped with a
5 ft (1.5 m) flexible drain hose with an
internal diameter of 7/8 (22 mm).
–Drain hose extensions and adapters
can be ordered from Miele.
The maximum drain hose length is
13 ft. (4 m), max. drain height: 39
(1 m).
– If the hose is to be directly fitted to
the drainage outlet on site, use the
supplied hose clip (see assembly
plan).
– The hose can be installed to the left
or right side.
– The existing drain pipe for the drain
hose is designed for various hose
diameters. The drain pipe must be
shortened if the drain pipe extends
too far into the drain hose. The drain
hose could get clogged.
–
The drain hose must not be
shortened.
Make sure the hose is installed
without kinking, pressure or being
pulled.Venting the drainage system
If the dishwasher drain hose is
connected to a floor drain or to a drain
pipe that is less than 8 (20 cm) above
the floor, the drain must be vented.
Otherwise the water inside the
dishwasher may siphon out during the
wash program.
Open the dishwasher door and
remove the lower basket.
Pull the lower spray arm firmly
upwards to remove.

Cut off the vent cap located at the
right rear of the triple filter system, as
illustrated.
Plumbing
57
 
						

							58
 
						

							59
 
						

							
Alteration rights reserved / 1711
G1262
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.M.-Nr. 07 768 790 / 02