Miele G 7881 User Manual

Fault Cause Solution
Before the start of a
program, the indicator
light Neutralizer
flashes and the
program cant be
started.Before addressing the
error:
–Turn the program
selector to the 12
o'clock positionf. The
error message is
erased.
–Press the "ON/OFF"
button to switch off the
machine.
Error message:Fdo:
The neutralizer container is
empty.Refill or replace the
neutralizer container.
Then:
– Switch the
washer-disinfector on.
– Restart the program.
A few minutes after the
start of a...

Fault Cause Solution
The refill salt message
Recharge is flashing.Because no regeneration
salt was added, the water
softener could not be
reactivated.Carefully fill the reservoir
with reactivation salt.
A few minutes after the
start of a program, the
Fill/Drain indicator
light flashes and the
program stops.Before addressing the
error:
–Turn the program
selector to the 12
o'clock positionf. The
error message is
erased.
–Press the "ON/OFF"
button to switch off the
machine.
Error message:F..E:...

Fault Cause Solution
The rinse program is
interrupted and the
Fill/Drain indicator
light is flashing.Before addressing the
error:
–Turn the program
selector to the 12
o'clock positionf. The
error message is
erased.
–Press the "ON/OFF"
button to switch off the
machine.
Error message:F..A:
There is a problem with the
water outflow.–Clean the filter
combination in the wash
cabinet.
– Clean the drain pump.
– Clean the non-return
valve.
– Remove any kinks in the
drain hose.
Then:
– Switch the...

Fault Cause Solution
After a program, there is
detergent residue left
behind in the dispenser.The dispenser was wet
when it was loaded.Make sure the dispenser is
dry before loading it.
The detergent dispenser
flap was blocked by items.Always arrange items such
that the dispenser cover
can open.
The detergent dispenser
cover will not close.Detergent residue is
blocking the latch.Wipe away any detergent
residue.
A banging noise can be
heard in the wash
cabinet.A wash arm is hitting the
items.Interrupt the...

Error Cause Solution
Items show signs of
corrosion.The chloride content of the
water is too high.Test your water
composition. If needed,
condition the water
externally and use
demineralized water.
Rust articles or a rust film
appears in the wash
cabinet, due to:
–excessive iron content in
the water,
–rusting items in the
same washload–Check the piping.
–Remove all rusty items
from use.
There are white
deposits and/or spots
on the items.The water softener setting
is too low.Test the tap water
hardness and...

Fault Cause Solution
There are spots on the
items.The rinse aid setting is too
low.Increase the rinse aid
dosage.
The rinse aid container is
empty.Add rinse aid.
The wash result is
unacceptable.The baskets and inserts
were incorrectly loaded or
overfull.Properly arrange the items.
Do not overload baskets
and inserts.
The detergent used was
not suited to the
type/amount of soiling.Use a suitable detergent
for machine washing.
The items were left soiled
for too long.Do not leave soiled items
unwashed for...

Temperature sensor
The washer-disinfector is equipped with
a (re-settable) temperature sensor that
switches off the heater when it
threatens to overheat. Overheating can
occur when, for example, large items
cover the heating elements or if the
filters in the wash cabinet are blocked.
If the display shows any of the following
fault messages:F01 - F03,F18,F19
(the water in the wash cabinet does not
get hot; the program sequence lasts
too long) take the following steps:
^Remove the underlying cause.
^Remove...

Cleaning the non-return valve
and drain pump
If you find that water has not been
pumped away at the end of a program,
the drain pump or non-return valve may
be blocked. You can remove the
blockage yourself.
^Remove the filter combination from
the wash cabinet.
^
Flip the fastening clamp to the side.
^
Pull the non-return valve up and out
and rinse it under running water.
,Caution: Use proper eye
protection when removing the
non-return valve.The drain pump is located beneath the
non-return valve (see...

Cleaning the filter in the water
inlet
There are filters in the screw connection
of the water inlet hose to protect the
water inlet valve. When the filters
become dirty, they need to be cleaned
so that enough water can flow into the
wash cabinet.
,The plastic housing of the water
connection contains an electrical
component. It must NOT be
submerged in water.Cleaning the filter
^Disconnect from the power supply.
^Turn off the water supply and
unscrew the water inlet hose.
^Clean the large area filter (1)...

If a fault occurs and cannot be
corrected using these Operating
Instructions, please contact Miele
Technical Service.
^When contacting the Service
department, you will need to quote
the model and serial numberof
your appliance.
This information can be found on the
model plate (see "Electrical
connection").
^You will also need to report the fault
message that appears in the
washer-disinfector display.
Correcting faults
60