Miele G 7893 Manual

The cleaning result must ensure that
the instruments have been disinfected
correctly, that no residues are left
behind, that subsequent sterilisation
can be carried out and that the
instruments can be used again safely.
Medical products are best reprocessed
using the DESIN vario TD programme.
The use of a suitable carrier (mobile
unit, module, insert etc.) is important to
ensure the adequate cleaning of
instruments and products. Examples
are given in the section "Areas of
application".
The...

aOn/Off switch I-0
bDoor releasea
cDisplay
d

aConnection for DOS module K 60 at
the rear of the machine
bService panel
cFilter combination
dSalt reservoir
eDispenser for powder cleaning agentfRinsing agent reservoir (with dosage
selector)
gRinsing agent level indicator
At the rear of the machine:
–
Interface connector RS 232
(optional)
–
Suction tube for external neutralising
agent container
Guide to the machine
13 

Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Rather than just throwing these
materials away, please ensure that they
are recycled.
Disposal of your old machine
Electrical and electronic
machines often contain materials
which,...

Electric door lock
This machine is equipped with an
electric door lock.
The door can only be opened when:
^the electricity supply to the machine
is switched on and
^the On-Off switchI-0is pressed in.
To open the doora
^Press the door release switch in as
far as it will go, and at the same time
grip the handle and open the door.
,Do not touch the heating
elements if you open the door during
or directly after the end of a
programme; you could burn
yourself. They remain hot for some
time after the end of...

In order to achieve good cleaning
results, the washer-disinfector needs to
operate with soft water. Hard water
results in the build-up of calcium
deposits on instruments etc. and in the
washer-disinfector.
Mains water with a hardness level
higher than 0.7 mmol/l (4° d – German
scale) needs to be softened. This takes
place automatically in the integrated
water softener.
–The water softener requires
reactivation salt.
–The washer-disinfector must be
programmed to correspond to the
water hardness in your...

Table of settings
°d mmol/l °fSetting
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
390.2
0.4
0.5
0.7
0.9
1.1
1.3
1.4
1.6
1.8
2.0
2.2
2.3
2.5
2.7
2.9
3.1
3.2
3.4
3.6
3.8
4.0
4.1
4.3
4.5
4.7
4.9
5.0
5.2
5.4
5.6
5.8
5.9
6.1
6.3
6.5
6.7
6.8
7.02
4
5
7
9
11
13
14
16
18
20
22
23
25
27
29
31
32
34
36
38
40
41
43
45
47
49
50
52
54
56
58
59
61
63
65
67
68
700*)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19 **)
20
21
22
23
24
25
26
27
28
29
30
31
32
33...

Filling the salt reservoir
Only use special coarse grained
reactivation salt with granules of
approx.1-4mm.Donotuseother
types of salt such as cooking salt,
agricultural grade or gritting salt. These
may contain insoluble additives which
can impair the functioning of the water
softener. If in doubt consult the Miele
Professional Department.
The salt reservoir holds approx. 2.5
kg of salt.
,Inadvertently filling the salt
reservoir with cleaning agent will
damage the water softener.
Before filling the salt...

Add salt indicator
Reactivation takes place automatically
during a programme.
The programme sequence indicator
lightaklights up whilst this is
happening.
^Add salt when the Add saltbk
indicator lights up.
Water softener
19 

This washer-disinfector can be fitted
with a top and bottom basket or a
mobile unit. Various inserts and special
baskets are also available for a wide
variety of instruments and utensils.
Select baskets and inserts which are
appropriate for the application.
Notes on the individual areas of
application and examples of loading
are given on the following pages.
Before starting a programme you
should carry out a visual check on
the following:
– Is everything correctly
loaded/connected for cleaning?
– Are the...