Miele G 7893 Manual

Baskets and inserts
Baskets and inserts should be checked
daily to make sure they are functioning
correctly. The washer-disinfector is
supplied with a check list.
The following need to be inspected:
–Check that rollers on baskets/inserts
are free of hindrance and that they
are secure.
–Check that the basket connector is at
the correct height and screwed on
correctly.
– Check that jets, sleeves and hose
adapters are securely held in
position in baskets/inserts.
– Check that washing solution can flow...

Drying unit (TA) - Maintenance
To change the filter
The filter must be changed ifSF2starts
to flash in the display.
To ensure the machine operates
correctly, useoriginal Miele HEPA
filtersonly (classification 12).
^Open the service panel.^Remove the filter from its holder, and
replace with a new one.
^Close the service panel.
Reset the filter operating hours
counter after changing the filter.
See "Programmable functions" for
how to do this.
Maintenance
52 

The following guide may help to find the reason for a fault and to correct it. You
should, however, note the following:
,Repairs should only be carried out by a Miele authorised and trained ser
-
vice technician in strict accordance with current local and national safety
regulations. Unauthorised or incorrect repairs could cause personal injury or
damage to the machine.
To avoid unnecessary service call-outs, check that the fault has not been caused
by incorrect operation.
To do this:
^Turn the programme...

Fault Possible cause Remedy
The8DOS indicator
starts flashing before
the start of a
programme. The
programme cannot be
started.Before trying to rectify the
problem, you must:
–Turn the programme
selector tof(the fault
code goes out).
–Switch the machine off
with theI-0switch.
Fault codeFdo:
The container for liquid
cleaning agent is empty.Fill the container with liquid
cleaning agent or replace
it with a new, full container.
Then:
– Switch the machine on.
– Start the programme
again.
A few minutes after...

Fault Possible cause Remedy
Thewindicator starts
flashing before the
start of a programme.
The programme cannot
be started.Before trying to rectify the
problem, you must:
–Turn the programme
selector tof(the fault
code goes out).
–Switch the machine off
with theI-0switch.
Fault codeFdo:
The neutralising agent
container is empty.Fill the container with
neutralising agent or
replace it with a new, full
container.
Then:
– Switch the machine on.
– Start the programme
again.
A few minutes after the
start of a...

Fault Possible cause Remedy
The Add salt indicator
lightkflashes.The salt reservoir has not
been replenished, meaning
that the water softener
could not be reactivated.Fill carefully with salt.
A few minutes after the
start of a programme,
thep/6indicator
flashes and the
programme is
cancelled.Before trying to rectify the
problem, you must:
–Turn the programme
selector tof(the fault
code goes out).
–Switch the machine off
with theI-0switch.
Fault codeF..E:
There is a water inlet fault.–Open the stopcock....

Fault Possible cause Remedy
The programme is
cancelled and the
p/6indicator
flashes.Before trying to rectify the
problem, you must:
–Turn the programme
selector tof(the fault
code goes out).
–Switch the machine off
with theI-0switch.
Fault codeF..A:
There is a water drainage
fault.–Clean the filters in the
wash cabinet.
–Clean the drain pump.
–Clean the non-return
valve.
– Remove any kinks and
straighten the drain
hose.
Then:
– Switch the machine on.
– Drain the water.
– Start the programme
again.
Water...

Fault Possible cause Remedy
Cleaning agent residue
is left in the dispenser
for powder cleaning
agent at the end of a
programme.The dispenser for powder
cleaning agent was still
damp when it was filled.Make sure the dispenser
is dry before adding
cleaning agent.
An item was blocking the
lid of the powder cleaning
agent dispenser.Arrange the items so that
the lid can open.
The powder cleaning
agent dispenser lid
cannot be closed
properly.Clogged detergent residue
is blocking the catch.Remove the residue....

Fault Possible cause Remedy
Glass utensils are
cloudy and etched.The items are not suitable
for machine processing.Only clean instruments that
are suitable for machine
processing in the machine.
Neutralisation has not
been carried out during
the programme cycle.Fill the neutralising agent
container.
The damage to glassware
was caused by too high a
wash temperature.Select a suitable
programme, or lower the
wash temperature.
The damage to glassware
was caused by a cleaning
agent that is too alkaline.Use a...

Fault Possible cause Remedy
White residues and/or
flecks are visible on
items.The water softener is
programmed to a setting
which is too low.Check the water hardness
level of the water supply
and programme the water
softener correctly.
Water entering the
machine through the AD
water connection is not
soft enough.Change the resin in the
aqua purificator.
The salt reservoir is empty. Fill carefully with salt.
The salt reservoir cap has
not been screwed on
correctly.Replace it making sure it
screws back on...