Miele K 14827 Operating And Installation Instructions

The active charcoal filters should be
changed approx. every 6 months.
When the Change active charcoal filter
indicator lights up red, the active
charcoal filters need to be changed.
To change the active charcoal
filters
^Pull the active charcoal filter holder
upwards to remove it from the shelf.
^
Take out the two filters and fit the new
filters into the holder with the
protruding cloth edge facing
downwards.
^
Place the holder in the middle of the
raised edge at the back of the shelf,
so that it clicks...

If you have delayed changing the
active charcoal filters and the indicator
is not lit up, you will need to reset the
counter when you replace the active
charcoal filters via the settings mode.
^Touch and leave your finger on the
sensor.
^At the same time, briefly touch the
On/Off sensor (without letting go of
thesensor).
^Leave your finger on thesensor for
another 5 seconds untilcappears in
the display.
^Touch thesensor repeatedly until
^appears in the display.
^
Touch the On/Off sensor.
^
Touch...

Repairs to electrical appliances
should only be carried out by a
suitably qualified and competent
person in strict accordance with
current local and national safety
regulations. Repairs and other work
by unqualified persons could be
dangerous. The manufacturer cannot
be held liable for unauthorised work.
What to do if...
. . . the appliance does not get cool.
^Check whether the appliance has
been switched on. The temperature
display must be lit up.
^Check that the plug is correctly
inserted into the...

Should the cover be damaged or
need to be removed due to damage,
exercise caution.Never look at the
lighting with optical instruments
(magnifying glass or similar).
. . . the change the active charcoal
filter indicator is red.
^Replace the active charcoal filters.
You can order replacement filters via
your Miele Chartered Agent or the Miele
Spare Parts Department.
..._F shows in the temperature
display.
There is a fault. Call the Service
Department.
...dn appears in the temperature
display.
The...

Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost free appliances you can sometimes just
hear the movement of the fan inside the appliance.
Remember that the noise of the compressor...

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Chartered Agent
or
–Miele.
You will find the address and
telephone number of Miele on the
back cover of the manual.
When contacting your Chartered Agent
or Miele, please quote the model and
serial number of your appliance. This
information is given on the data plate
inside your appliance.
After Sales
36
 

Electrical connection
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations.
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an AC single phase
220-240 V 50 Hz supply.
The voltage and frequency are given on
the data plate. Please ensure that these
match the household mains supply. The
fuse rating is quoted on the plug.
Connection should be made via a
suitable...

Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliances energy
consumption.
Side-by-side installation
To avoid a build-up of condensation
and resultant damage, refrigerators and
freezers should not generally be
installed side by side next to other such
appliances.
However, some appliances have
side-wall heating making them suitable
for side-by-side installation with this
refrigerator.
Your Miele Chartered Agent...

Installation
^Remove the cable clip from the back
of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^Carefully push the appliance into
position with the back against the
wall.
Aligning the appliance
^To align the appliance, adjust the
front feet using the spanner supplied.
^
If necessary, also align the two rear
adjusting devicesausing socket
wrenchb.
Turn the adjusting device clockwise
to raise the appliance up at the back.^Unscrew...

Appliance dimensions
ABC
K 14827 SD ed1852 mm 600 mm 630 mm
Installation
40