Miele K 14827 Operating And Installation Instructions

The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a flat-bladed screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Two people are needed for
changing the door hinging.
Removing the door handle
^
Pull door handleatowards you. Side
sectionbslides back.
^
Pull side sectionbout of the guides
on the mounting plate.
^
Undo the 4 screws (Torx 15)...

Removing the soft-close door
mechanism
The soft-close door mechanism is at the
bottom of the door.
^Open the appliance door.
^Gently remove panelafrom the
soft-close mechanism by inserting a
flat-bladed screwdriver into the gap
from above and easing it off bit by
bit.
Take care not to damage the door
seal.
If the door seal becomes damaged,
the door will no longer close
properly and cooling will be
impaired.
^
Slide panelatowards the appliance,
and leave it hanging between the
door and the appliance.^Fit...

^Slide soft-close mechanism bracket
fas far as it will go towards the
handle side of the door, and undo
screwsgon the soft-close
mechanism.
^Using a flat-bladed screwdriver, slide
the soft-close door mechanism
towards the handle side of the door,
and lever it out at the side.
^Then place it to one side.
Changing over the door
Make sure the door shelves are
empty!
^
Close the door.^Remove coveraby sliding it
forwards from the back and then
lifting it off.
^Remove coverbby pulling it
upwards.
Caution. The...

^Remove caphfrom the hinge bush
in the door and refit on the opposite
side.
^
Remove coveraby pulling it
forwards.
^
Pull coverboff.
^
Screw footcinto the hinge pin as far
as it will go.^With the help of another person,
carefully tip the appliance back and
pull hinge pincdownwards to
remove.
^Take care not to lose hinge bushd.
^Undo screwseand take hinge plate
foff.
^Remove covergand refit on the
opposite side.
^Refit hinge platefonto the other
side using the 2outerscrews. To
make it possible to align...

^Fit hinge plateconto the opposite
side and secure it with screwsd.
If necessary drill a pilot hole for the
screws.
^Fit coversaandbto their opposite
sides.
^Align the door with the appliance
housing using the outer long slots in
the lower hinge plate. Then tighten
the screws.
Replacing the soft-close door
mechanism
^
Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.^Insert the soft-close mechanism back
into the door, starting at the right
hand side.
^Slide the soft-close...

^Attach panelbto soft-close
mechanism bracketd.
^Align bracketdto the hinge plate,
and insert pinefrom above so that
the right angle fits into the recess.
^Click coverfback into place.
Make sure that coverffits properly so
that the door can be closed without
hindrance and the pin is protected.
^Remove retaining clipg.
^
Replace panelbonto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^
Close the door.Refitting the handle
Please make sure you...

It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^Realign mounting platecwith grub
screwsauntil the mounting plate
and the side section of the handled
are at the correct angle and the side
section does not touch the door seal
when the door is opened.
Changing...

The appliance door can be aligned to
the housing using the outer long slots in
the lower hinge plate.
In the following illustration the door
is shown open to make it easier to
see what you have to do.
^Remove centre screwafrom the
hinge plate.
^Slightly loosen both outer screwsb.
^Align the door by sliding the hinge
plate to the left or right.
^
Then tighten screwsbagain. Screw
adoes not need to be refitted.
Aligning the appliance
48
 

aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm
2to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work...

50