Miele Kfn 14823 Sded Operating And Installation Instructions

The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a flat-bladed screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Two people are needed for
changing the door hinging.
Removing the door handles:
^
Pull door handleatowards you. Side
sectionbslides back.
^
Pull side sectionbout of the guides
on the mounting plate.
^
Undo the 4 screws (Torx...

Before beginning, make sure that
the door shelves are empty!
Removing the soft-close mechanism
for the upper door:
^Open the upper door.
^Prise openafrom the soft-close
mechanism by inserting a flat-bladed
screwdriver into the gap from above
and easing it off bit by bit.
Take care not to damage the door
seal.
If the door seal becomes damaged,
the door will no longer close
properly and cooling will be
impaired.^Slide panelatowards the appliance,
and leave it hanging between the
door and the appliance....

^Slide soft-close mechanism bracket
fas far as it will go towards the
handle side of the door, and undo
screwsgon the soft-close
mechanism.
^Using a flat-bladed screwdriver, slide
the soft-close door mechanism
towards the handle side of the door,
and lever it out at the side.
^Then place it to one side.Removing the upper door:
^Gently loosen coverhby carefully
inserting a flat-bladed screwdriver
into the gap.
^Remove coverhtogether with
retaineri.
^Then separate retainerifrom cover
h, by pushing it...

Caution. The upper door is not
secure as soon as the upper hinge
plate is removed.
^Close the upper door.
^Undo screwsmin upper hinge plate
nand pull it upwards and off.
^Carefully lift the upper door off and
place it to one side.
^Make sure that you leave the hinge
pin in the hinge plate in the middle of
the appliance, as otherwise the lower
door will be unsecured.
^Then fit coverhtogether with
retainerion the opposite side.
^Refit coverlon the opposite side.
Removing the lower soft-close door...

^Push hinge pineup and out from
underneath.
The soft-close mechanism is now no
longer fixed to the appliance.
^Remove panela.
^
Slide soft-close mechanism bracket
fas far as it will go towards the
handle side of the door, and undo
screwsgon the soft-close
mechanism.
^
Using a flat-bladed screwdriver, slide
the soft-close door mechanism
towards the handle side of the door,
and lever it out at the side.
^
Then place it to one side.Removing the lower door:
^Close the lower appliance door.
^Pull the middle...

^Remove caplfrom the bush in the
door and refit on the opposite side.
Refitting the lower door:
^
Remove coveraby pulling it
forwards.
^
Pull coverboff.
^
Screw footcinto hinge pin as far as it
will go.^With the help of another person,
carefully tilt the appliance backwards
and pull hinge pincout.
^Take care not to lose hinge bushd.
^Undo screwseand take hinge plate
foff.
^Remove covergand refit on the
opposite side.
^Refit hinge platefonto the other
side using the 2outerscrews. To
make it possible to...

^Fit hinge piniinto middle hinge
platekin the lower door.
Replacing the lower soft-close door
mechanism:
^
Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.^Insert the soft-close mechanism back
into the door, starting at the right
hand side.
^Slide the soft-close mechanism back
into the door as far as it will go
towards the appliance using a
flat-headed screwdriver.
The screw holes on the left and right
must line up perfectly.
^
First screw the soft-close mechanism
onto the...

^Attach panelbto soft-close
mechanism bracketd.
^Align bracketdto the hinge plate,
and insert pinefrom above so that
the right angle fits into the recess.
^Click coverfback into place.
Make sure that coverffits properly so
that the door can be closed without
hindrance and the pin is protected.
^Remove retaining clipg.
^
Replace panelbonto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^
Close the lower appliance door.Refitting the upper door:...

Replacing the upper soft-close door
mechanism:
^Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.
^
Insert the soft-close mechanism back
into the door, starting at the right
hand side.^Slide the soft-close mechanism back
into the door as far as it will go
towards the appliance using a
flat-headed screwdriver.
The screw holes on the left and right
must line up perfectly.
^
First screw the soft-close mechanism
onto the appliance side, then onto
the handle sidec, pushing it firmly...

Make sure that coverefits properly so
that the door can be closed without
hindrance and the pin is protected.
^Remove retaining clipg.
^Replace panelbonto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^Close the upper door.
Changing the door hinging
60