Miele Pw 5065 Operating Manual

Drainage
There are two drainage options for this
machine:
Drain valve
The machine is drained with a
motorized drain valve. A connection
can be made to an on-site floor drain
(gully with an air gap) on an angle.
Drain pump
The wash water is drained using a
pump with a 3 ft (1 m) delivery height.
Make sure there are no kinks in the
drain hose. The elbow on the end of the
drain hose can be turned or removed if
necessary.
Possible connections:
1. Directly into a sink:Hook the hose
over the edge of the sink...

Electrical connection
,This installation should be
performed by an experienced and
qualified technician, in accordance
with local codes and regulations.
The washer comes with a power cord
without a plug.
The machine is supplied as standard
for connection to a 208 V, 60 Hz, 20 A,
2-phase electrical supply*.
For extra safety it is advisable to install
a residual current device (RCD) with a
trip current of 30 mA.
The machine must only be connected
to the voltage and frequency shown on
the data plate.
,*To...

Height 337/16 (85 cm)
Width 23
7/16 (59.5 cm)
Depth 283/8 (72 cm)
Depth with the door open 44
1/8 (112 cm)
Weight 236 lb (107 kg)
Maximum floor load 2778 Newton (approx. 278 kg)
Capacity 13.2 lbs (6.5 kg) dry laundry
Fuse rating see data plate
Rated load see data plate
Fuse rating see data plate
Noise level during spinning
(Noise emission 3. GSGV)< 70 dB(A)
Minimum water flow pressure 14.5 psi (1 bar)
Maximum water pressure 145 psi (10 bar)
Length of intake hose 5’3 (1.6 m)
Length of power cord 5’3 (1.6...

Disposal of the packing
materials
The cardboard box and packing
materials protect the appliance during
shipping.
To prevent suffocation of children
ensure that any plastic wrapping, bags,
etc. are disposed of safely and kept out
of the reach of children.
Please recycle.
Disposal of an old appliance
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Ensure that the appliance presents no
danger to...

Menu SettingsJ
to adjust standard settings
The washer controls can be adjusted to changing demands through the settings
menu.
 

Accessing the "Settings"J
^Turn the program selector to Finish.
The main menu shows.
12:03
Selecting a program
SettingsF
^Confirm with OK.
^The Settings menu is selected.
CBackA
LanguageF
Suds cooling
^Set the desired setting with the
buttons+/–and confirm with OK.
Leaving the Settings menu
^Select Back and confirm with OK.
The display shows the main menu.
LanguageJ
The display contents can be shown
in different languages.
The displayed language can be
changed by the sub-menu
LanguageJ.
The flag...

Time of day
This selection allows the clock to be
shown as 24 hours, 12 hours or not
at all. The time of day is also set
here.
If the clock is not selected the delay
start can only be shown as a 24 hour
timer. The display will show the timer
counting down until the start of the
program but not the current time of day.
Selecting the clock display
^Select the desired clock display and
confirm.
The display shows the clock setting.
Set the time of day
^Set the hours with the buttons+/–
and confirm with OK....

Standby
The display goes out after 10
minutes and the Start button
flashes slowly to save energy.
Two options can be selected:
On
The display will go into standby mode:
–if no program is selected after the
machine is turned on.
–after a program has started.
– at the end of a program.
Not in current prog.
(factory default)
The Standby function will be turned on
if no program was selected after the
machine was turned on.
By turning the program selector or
pressing any button the display is
turned on...

The menu "Settings - Supervisor
level" has to be "activated" by a
Miele service technician or dealer.
The menu Settings (except
LanguageJ) is locked with a code
to prevent unwanted access.
CBackA
FLanguageF
Supervisor level
^Select the Supervisor level and
confirm.
CBackA
XEnter code
^Select the code and confirm.
Entering the code
A three digit code must be entered. On
delivery the code is:0 0 0.
0__
Enter code
^
Enter the first digit with the+button.
Confirm with OK.
^
Enter the second...

LanguageJ
The display contents can be shown
in different languages.
The fixed language selection can be
set in the sub-menu LanguagesJ.
^Select the desired language and
confirm with OK.
Supervisor level
The access code for the operator
level can be changed.
^Enter the old code.
^Enter the new code.
Once the new code is confirmed, the
beginning of the Settings menu will
appear.
Auto load control
If the Auto load control is turned off
the program will run as if for a full
load.
The machine comes factory...