Mitsubishi Ex100u Projector User Manual

							 EN - 11
ENGLISH
Projector + Computer
For computer with Mini D-SUB
Important:
•  When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly. 
•  Some computers require additional connectors or analog RGB output adapters to be connected with this projector. 
Contact your dealer for further information. 
•  This projector uses stereo pin jack for its audio input. Check the type of the audio output terminal of the connected 
computer and prepare a proper cable for connection. Some computers don't have the audio output terminal.
•  Speaker output is mono.
•  When the audio cable is connected to the AUDIO OUT terminal, the speaker output is muted.
For Macintosh
•  If your Macintosh has no video port, a monitor output adapter is required. Contact your dealer for further information.
•  Some Macintoshes require a MAC adapter for the RGB cable for connection with this projector. Contact your dealer 
for further information.
About DDC
The COMPUTER/COMPONENT VIDEO IN-1 terminal of this projector complies with the DDC1/2B standard. When a 
computer supporting this standard is connected to this terminal, the computer will automatically load the information 
from this projector and prepare for output of appropriate images. 
•  After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the 
wall outlet fi rst, and then boot up the computer.
•  You may need to install the DDC driver, depending on the computer you use. In this case, you need to download 
the driver from our Web site. Contact your dealer or Mitsubishi sales offi ce for further information.
AUDIO OUT
MONITOR OUTPUT
COMPUTER/COMPONENT 
VIDEO IN-1/2
AUDIO INAUDIO OUT
MONITOR  OUT
RGB cable for PC 
Computer
to monitor 
port
PC audio cable (option)to PC audio
output RGB cable for PC (option)
Necessary when outputting to both a PC monitor and the projector.
Audio cable (option) 
						

							EN - 12
Preparation
1.  Tilt up the project to the appropriate angle. 
2.  Press the foot adjustment buttons next to the adjust-
ment feet (rear), and the adjustment feet will come 
out. 
3.  Release the buttons to lock the adjustment feet (rear) 
to that position.
4.  Rotate the adjustment feet (rear) for fi ne adjustment.
After using the projector:
5.  Put the adjustment feet (rear) back into the projector 
by pressing the foot adjustment buttons.
Important: 
•  If necessary, rotate the adjustment feet (front) for fi ne 
adjustment. 
•  Install the screen on a fl at wall at 90 degrees to the 
fl oor. 
•  Slanting the projector more than ±10˚ (right and left) 
or ±15˚ (front and rear) may cause trouble or explo-
sion of the lamp. You can tilt the projector up to 7 
degrees using the adjustment feet only.  
•  Images may not be projected in a shape of a regular 
rectangle or with its aspect ratio 4:3, depending on 
the installation conditions of the projector and the 
screen. 
•  To correct vertical keystone distortion, press the 
KEYSTONE button on the projector or the remote 
control to display KEYSTONE, and adjust the image 
by pressing the 
,  button (or VOLUME +, - but-
ton on the remote control). 
In the following cases:Preparation for projection
1.  Attach the provided power cord to the projector.
2.  Plug the power cord in the wall outlet. 
3.  Remove the lens cap.
Warning:
•  Do not look into the lens directly when the projector is 
on.
•  The lens cap is for protecting the lens. If you leave 
the lens cap on the lens with the projector turned 
on, it may be deformed because of heat build-up. 
Remove the lens cap when you turn on the projector.
•  The power cords for use in the U.S. and Europe are 
provided with this projector. Use the appropriate 
cord for your country. 
•  This projector uses the power plug of three-pin 
grounding type. Do not remove the grounding pin 
from the power plug. If the power plug doesn't fi t 
your wall outlet, ask an electrician to change the wall 
outlet. 
•  The provided power cord for the U.S. is rated at 120 V. 
Never connect this cord to any outlet or power sup-
ply using other voltages or frequencies than rated. If 
you want to use a power supply using other voltage 
than rated, prepare an appropriate power cord sepa-
rately.
•  Use 100-240 V AC 50/60 Hz to prevent fi re or elec-
tric shock.
•  Do not place any objects on the power cord or do 
not place the projector near heat sources to prevent 
damage to the power cord. If the power cord should 
be damaged, contact your dealer for replacement 
because it may cause fi re or electric shock. 
•  Do not modify or alter the power cord. If the power 
cord is modifi ed or altered, it may cause fi re or elec-
tric shock. 
Caution:
•  Plug in the power cord fi rmly. When unplugging, hold 
and pull the power plug, not the power cord.
•  Do not plug in or out the power cord with your hand 
wet. It may cause electric shock.
Adjustment of the projection angle
For the best projection, project images on a fl at screen 
installed at 90 degrees to the fl oor. If necessary, tilt the 
projector using the two adjustment feet on the bottom 
of the projector. 
Important: 
•  When the keystone adjustment is carried out, the 
adjustment value is indicated.  Note that this value 
doesn't mean a projection angle. 
•  The allowable range of the adjustment value in the 
keystone adjustment varies depending on the instal-
lation conditions. 
•  When the keystone adjustment takes effect, the res-
olution decreases. In addition, stripes may appear or 
straight lines may bend in images with complicated 
patterns. They are not due to product malfunctions.  
•  Noise may appear on the screen during the keystone 
adjustment because of the type of the video signal 
being projected and the setting values of the key-
stone adjustment. In such cases, set the keystone 
adjustment values in the range where the image is 
displayed without noise. 
•  When the keystone adjustment is carried out, the im-
age may not be displayed correctly because of the 
type of input signal.
For ES100U only
•  When the 720p or 1080i signal is input, the keystone 
adjustment ranges are limited.
Screen
Adjustment feet (Rear)
Press  the 

(or -) button.Press the 

 
(or +) button. 
						

							 EN - 13
ENGLISH
Basic operation
•  The projector starts warming up when the POWER 
button is pressed. During the warm-up process, 
images may appear dark and no commands are ac-
cepted.
•  By blinking red, the STATUS indicator indicates that 
the lamp should be replaced soon. Replace the lamp 
when the STATUS indicator blinks red. (See page 23 
and 26.) 
•  Images may not be projected with good quality in 
an extremely hot or cold environment. (This is not a 
product malfunction.) 
4.  Adjust the focus by turning the focus ring.
5.  Choose your desired external input source using  the 
COMPUTER or VIDEO button.
•  The input source is switched between COM-
PUTER 1 and COMPUTER 2 at every press of the 
COMPUTER button on the control panel.
•  The input source is switched between VIDEO(1) 
and S-VIDEO(2) at every press of the VIDEO but-
ton on the control panel. 
•  The projector automatically selects the appropri-
ate signal format. The selected signal format is 
displayed on the screen.
•  The COMPUTER and VIDEO buttons don't func-
tion while the menu is being displayed. 
•  When COMPUTER 1 or COMPUTER 2 is chosen 
as the source, 
images supplied from the compu-
ter may fl icker. Press the  or  button on the 
remote control to reduce fl icker, if it occurs.
•  To avoid permanently imprinting a fi xed image 
onto your projector, please do not display the 
same stationary images for long 
period.
6.   Adjust the image size by turning the zoom ring.
•  If necessary, adjust the focus and zoom again. 
Power-on
1.  Turn on the device connected to the projector fi rst.
2.  Plug the power cord in the wall outlet. 
•  The POWER indicator lights up. 
•  If the power cord is unplugged from the wall 
outlet before the projector is cooled down com-
pletely after use, the fans may start rotating when 
the power cord is plugged in next time and the 
POWER button may not function. In this case, 
wait for the fans to stop and press the POWER 
button to light the indicator. 
3.  Press the POWER button on the control panel or the 
ON button on the remote control.
•  It may take about one minute for the lamp to light 
up. 
•  The lamp occasionally fails to light up. Wait a few 
minutes and try to light the lamp again. 
•  After the POWER button is pressed, the image 
may fl icker before the lamp becomes stable. This 
is not a product malfunction. 
For EX100U
•  Regardless of the setting of LAMP MODE in the 
INSTALLATION menu, the STANDARD lamp mode 
is activated by default whenever the projector is 
turned on. When LAMP MODE has been set to 
LOW, the lamp mode changes from STANDARD 
to LOW about one minute after turn-on. 
For ES100U 
•  You can’t change the lamp mode for one minute 
after turning on the projector. 
ON
STILL MUTE
MENU
COMPUTER
16:9
12 12
ENTER
VOLUME
UP
DOWNPA G E
POWER OFF
AUTO POSITION
KEYSTONE
VIDEO
55
5 3, 
1, 2P O W E R S TAT U S
31, 2
4
6
ConditionIndicator
STATUS
POWER
-
Stand-by
Red
When the lamp is on.
Green
Green
Important:
•  Do not cover the lens with the lens cap while the 
lamp is on. Do not strip off the aluminum sheet in-
side the lens cap. 
						

							EN - 14
VOLUME     10
Volume from the speaker
Press the VOLUME + or - button to change the volume 
from the speaker.
The volume control bar will appear on the screen.
•  The volume control bar will disappear about 10 sec-
onds after the VOLUME button is released.
•  The VOLUME buttons dont function while the menu 
selection bar or the menu is being displayed. 
•  When a high-level audio signal, such as a DVD audio 
signal, is supplied to the AUDIO IN terminal, the out-
put from the speaker may be distorted.
AV mute
The video and audio signals are temporarily muted 
when the MUTE button is pressed. To cancel muting, 
press the MUTE button again.
ANAMORPHIC mode
When playing DVD discs containing data of letterboxed 
image, press the 16:9 button. Exit the ANAMORPHIC 
mode, by pressing the 16:9 button again.
Important: 
•  When a letterboxed image is kept displayd for a long 
time before displaying 4:3 image, the afterimages of 
the black bars may appear on the 4:3 image screen. 
Consult your dealer in this case.
Caution: 
•  After using the projector, wait one minute for the air 
outlet fans to stop. Then unplug the power cord from 
the wall outlet.
•  The lamp cant be lit again for one minute after 
turned off for safety purpose. It will take another one 
minute for the STATUS indicator to go out. If you 
want to turn on the projector again, wait until the in-
dicator goes out, and then press the POWER button.
•  The air outlet fans rotate faster as the temperature 
around the projector rises.
•  When the temperature around the projector rises  
high, the sign TEMPERATURE!! blinks red on the 
screen. If the temperature stays high, the lamp will 
go out automatically.
Important: 
•  Do not display a still picture for a long time because 
the afterimages may persist on the screen.
Power-off
Use the following procedure to turn off the projector. Do 
not turn off the projector by unplugging the power cord 
while the lamp is on. Unplugging while the lamp is on 
degrades the lamps performance and causes failure in 
the projector. 
11.  Press the POWER button on the control panel or the 
OFF button on the remote control.
• The message POWER OFF? YES : PRESS 
AGAIN appears on the screen.
•  To cancel, press any button except the POWER 
button. (Some buttons on the remote control 
dont function for cancel.)
22.  Press the POWER button on the control panel or the 
OFF button on the remote control within 10 seconds 
again.
•  The lamp will go out and the STATUS indicator 
will start blinking. 
•  Though the lamp goes out at this second press of 
the POWER button (or OFF button), the air outlet 
fans continue operating for one minute to cool 
down the lamp. The STATUS indicator will stop 
blinking. 
33.  Unplug the power cord.
•  The POWER indicator will go out. 
•  If the power cord should be unplugged acci-
dentally while either the air inlet fan or the air 
outlet fans are operating or the lamp is on, allow 
the projector to cool down for 10 minutes with 
the power off. To light the lamp again, press 
the POWER button (or OFF button). If the lamp 
doesnt light up immediately, repeat pressing 
the POWER button (or OFF button) two or three 
times. If it should still fail to light up, replace the 
lamp. 
Important: 
•  When storing the projector in the provided carrying 
case, the lens should face up.
AUTO POSITION button
When the image isnt projected in the right position with 
COMPUTER selected as the input source, follow the 
procedure below. 
1.  Project a bright image such as the  Recycle Bin 
window on the full screen.
2.  If the screen saver is running, turn it off. 
3.  Press the AUTO POSITION button.
•  If the image is still not in the right position, adjust 
the image position using the SIGNAL menu. See 
page 19.
Basic operation (continued) 
						

							EN - 15
ENGLISH
Menu operation
IMAGE
XGA60opt.
INSTALLATION
opt.XGA60
INSTALLATION
opt.
AUTO POWER 
ON
AUTO POWER 
OFF
OFF OFF
XGA60
AUTO POWER 
ON
AUTO POWER 
OFF
OFF OFF
AUTO POWER 
ON
AUTO POWER 
OFF
30 minOFF
Basic operation
Several settings can be adjusted using the menu. 
Example : Auto power off time setting 
1.  Press the MENU button.
2.  Press the  or  button to select INSTALLATION.
3.  Press the ENTER button (or  button).4.  Press the 
 or  button to select AUTO POWER 
OFF. 
5.  Press the  or  button to adjust the auto power 
off time.   
6.  Exit the menu by pressing the MENU button sev-
eral times.
Important:
•  When the button doesn't function,  unplug the 
power cord from the wall outlet. Wait about 10 
minutes, plug the power cord in, and try again.  
•  After selecting the items marked with 
, press 
the ENTER button.
IMAGE CONTRAST ±30
BRIGHTNESS ±30
sRGB ON, OFF
CineRichColor AUTO, 0 - 10
STANDARD
LOW
HIGH
USER     COLOR TEMP.
COLOR  ±10
TINT  ±10
SHARPNESS  ±5
GAMMA MODE AUTO, DYNAMIC, STANDARD, THEATERCONTRAST R  ±30
CONTRAST B  ±30
BRIGHTNESS R  ±30
BRIGHTNESS B  ±30
INSTALLATION
OFF, MIRROR, INVERT, MIRROR INVERT
AUTO POWER ON
ON , OFF
RESET ALL OK  AUTO POWER OFF
ON , OFF
FEATURE MENU POSITION 1 (Upper left), 2(Lower right)IMAGE REVERSE SPLASH SCREEN
BLUE, BLACK BACK COLOR
STANDARD, LOW LAMP MODE
MENU ACCESS PASSWORD FUNCTION
VIDEO SIGNAL AUTO , NTSC , PAL , SECAM , 4.43NTSC , PAL-M , PAL-N , PAL-60
LANGUAGE
, English, Español, Deutsch, Français, Italiano,        ,          ,             ,    
SIGNALHORIZ.POSITION
HOLD0 - 999
VERT.POSITION 0 - 999
FINE SYNC. 0 - 31
TRACKING
USER0 - 9999
CLAMP POSITION0 - 63
CLAMP WIDTH 1 - 63 *5
*3
*3
*3
*3
*3
AUTO , OFF CINEMA MODE
*5
*5
ON
BEGIN 0 - 15
END 0 - 15 OFF
COMPUTER INPUTRGB, YCBCR / YPBPR
SET UPOFF / 3.5% / 7.5%
*5
*5 *5
*5
OFF,  5,  10,  15,  30,  60 min
OK 
ON , OFF ANAMORPHIC
ON
UNLOCKOK 
LOCK *1 *1
*1
*2
*1
*1
*4 *2
* 1: Not available when sRGB is set to ON.
* 2: Not available with certain signals.
* 3: Not available when the source is a VIDEO 
      or S-VIDEO signal.
* 4: Available only when the input signal is TV60, 480i.
* 5: Setting range differs depending on the input signals.
(These items are not available when the 
input source is COMPUTER.) 
						

							EN - 16
Menu operation (continued)
INSTALLATION
opt.
ON
BACK COLOR AUTO POWER 
ON
AUTO POWER 
OFF
SPLASH 
SCREEN
LAMP MODEON
BLUEOFF OFF
STANDARD
OFF IMAGE 
REVERSE
XGA60
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
CineRichColor AUTO
OFF
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE sRGB
opt.
1 IMAGE
CONTRAST ............................ Use to adjust the image contrast. The contrast 
becomes higher as the value increases.
BRIGHTNESS ......................... Use to adjust the image brightness. The image 
becomes brighter as the value increases.
CineRichColor ........................ Use to adjust the white level of the projected 
image. Select AUTO for normal use.
sRGB ...................................... Choose ON for projection emphasizing on the 
color reproducibility.
• When sRGB is ON, CineRichColor, COLOR 
TEMP., COLOR, TINT and GAMMA MODE 
can't be adjusted.
COLOR TEMP. ........................ Use to adjust the color temperature. See page 18.
COLOR ................................... Use to adjust the color intensity of the image.
TINT ........................................ Use to adjust the color balance of the image. The 
color balance shifts to green as the value increases and shifts to purple as the value 
decreases. (Available only when VIDEO or S-VIDEO is chosen as the source.)
• When the TV50 (PAL, SECAM) signal is input, TINT can't be adjusted.
SHARPNESS .......................... Use to adjust the image sharpness. The image becomes sharp as the value increases. 
(Not available with certain signals.)
GAMMA MODE ...................... When AUTO is selected, the appropriate gamma mode is automatically selected 
depending on the input signal. For normal use, select  AUTO. Select DYNAMIC for 
computer sources. Select STANDARD for sport scenes and video sources. Select 
THEATER for fi lm sources. 
2 INSTALLATION
AUTO POWER ON ................. When ON is chosen, the lamp is automatically lit 
when the power cord is plugged in the wall outlet. 
Choose ON when using the projector mounted on 
the ceiling. 
•  The projector is in the stand-by mode when the 
lamp is off.  Use the remote control to turn on 
the lamp. 
AUTO POWER OFF ................ Use to set the time elapsed before the projector 
enters the stand-by mode when there is no signal 
input from the source. 
SPLASH SCREEN .................. Choose ON to display the splash screen when the 
power is turned on. 
BACK COLOR ........................ Use to select the background from among BLUE and BLACK, which will be displayed 
when there is no signal input from the source. 
LAMP MODE .......................... Use to change the brightness of the lamp. When LOW is chosen, the lamp brightness 
is kept low and the projector operating noise is reduced, resulting in a longer lamp 
replacement interval. 
•  When the lamp mode is switched, the projected image may fl icker. This is not a 
product malfunction.
•  Do not change the setting of LAMP MODE frequently. 
For EX100U
•  When LAMP MODE has been set to LOW, the lamp mode changes from STAN-
DARD to LOW about one minute after turn-on. 
For ES100U 
•  You can’t change the lamp mode for one minute after turning on the projector. 
IMAGE REVERSE ................... Use to reverse the projected image. Select MIRROR for rear projection with the 
tabletop-mounted projector. Select MIRROR INVERT for front projection with the 
ceiling-mounted projector.   
						

							EN - 17
ENGLISH
3 FEATURE
MENU POSITION ................... Use to select the position of the menu on the 
screen,  1. 
 (upper left) or 2.  (lower right).
CINEMA MODE ...................... When AUTO is selected, the fi lm mode will be 
automatically activated when a fi lm source signal 
is inputted. When OFF is selected, the fi lm mode 
will not be activated. 
VIDEO SIGNAL ....................... When AUTO is selected, the appropriate video 
format is automatically selected depending on the 
input signal. If the image isnt displayed correctly, 
select the desired video format manually.
ANAMORPHIC ....................... Select ON when playing DVD discs containing data of widescreen images.
PASSWORD FUNCTION ........ Use to change the mode of the password lock or to enable or cancel the password 
lock. See page 21 for details. 
LANGUAGE ............................ Use to select the language used in the menu. (
 / English / Español / Deutsch / 
Français / Italiano / 
/  /  / PORTUGUÊS).
RESET ALL ............................. Use to reset the menu settings (except PASSWORD FUNCTION, and LANGUAGE ). 
•  CINEMA MODE can be adjusted only when a TV50, TV60, 480i, 576i signal is being displayed.
•  When VIDEO SIGNAL is set to AUTO, the image may not be projected with correct colors. Change the setting of 
VIDEO SIGNAL depending on the input signal in such cases.
4 SIGNAL
HORIZ. POSITION .................. Use to adjust the horizontal position of the image. 
VERT. POSITION .................... Use to adjust the vertical position of the image. 
FINE SYNC. ............................ Use to synchronize the projector with the PC input 
signal so that the image is not blurred.
TRACKING ............................. Use to eliminate image noise such as wide stripes.
COMPUTER INPUT ................ The projector adjusts its settings automatically 
when connected to a DVD player equipped with 
a component video output (Y, C
B, CR). When the 
projector is connected with a device having an 
RGB terminal, choose RGB manually.
SET UP ................................... When OFF is selected, the black area becomes   
make lighter. When 3.5% or 7.5% is selected, the 
black area becomes thicker. 
HOLD ..................................... Use to adjust the image when fl agging occurs near the top of the screen.
5 SIGNAL - USER (No need to adjust in normal use.)
CLAMP POSITION/
CLAMP WIDTH ...................... Use to correct solid white or solid black in the 
projected image. 
Important:
•  You can set the IMAGE, SIGNAL, and SIGNAL-USER menus only when the signal is supplied. 
FEATURE
XGA60
AUTO
opt.
MENU POSITION
VIDEO SIGNAL?
RESET ALL
English
LANGUAGEAË
OK
MENU ACCESS PASSWORD
FUNCTION
ANAMORPHICCINEMA MODEAUTO
1.
ON
CLAMP 
POSITIONUSER
0
CLAMP WIDTH 1
R G BR G B
SIGNAL
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER 
INPUTRGB
FINE SYNC. 0
USER
XGA60opt.
OK
ONHOLD
7.5%
SET UP 
						

							EN - 18
Image adjustment
CONTRAST R
USER
0
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS B 0
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
CineRichColor AUTO
OFF
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE sRGB
opt.
Color temperature
1.  Select COLOR TEMP. in the IMAGE menu. 
2.  Press the  or  button to select USER 
. 
3.  Press the ENTER button.
4.  Press the 
 or  button to select the desired item. 
5.  Press the  or  button to adjust the selected item. 
6.  Repeat steps 4 and 5 for optimum adjustment re-
sults.
7.  Exit the menu by pressing the MENU button several 
times.
About color temperature
There are different kinds of white color. Color tem-
perature is a way to show the differences in white. 
White of which temperature is low appears reddish. 
When the color temperature rises, white appears blu-
ish. This projector adjusts this color temperature by 
changing the values of contrast blue and red.
To rise the color temperature:
Increase the CONTRAST B (blue) and decrease the 
CONTRAST R (red).
To reduce the color temperature:
Decrease the CONTRAST B (blue) and increase the 
CONTRAST R (red).
Image adjustment
You can adjust the image using the IMAGE menu. 
To control the white-to-black level of the image :
Adjust CONTRAST in the IMAGE menu.  Press the  
button to increase the contrast and the  button to 
reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in the IMAGE menu.  Press the  
button to lighten the image and the  button to darken 
it.
To determine the intensity of the color :
Adjust COLOR in the IMAGE menu.  Press the 
 but-
ton to increase the amount of color in the image and 
the 
 button to decrease it.
To adjust the red-green color balance of the image :
Adjust TINT in the IMAGE menu.  Press the  button to 
increase the amount of green in the image and the  
button to increase the amount of red in the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in the IMAGE menu.  Press the  
button to sharpen the image and the  button to soften 
the image. 
						

							EN - 19
ENGLISH
Adjustment of the image from the computer
This projector adjusts the format of the video signal 
supplied from the computer. However, sometimes im-
ages are not projected correctly owing to the type of 
the computer used. When the image from the computer 
isnt projected correctly, press the AUTO POSITION 
button. (See page 14.) If the image isnt projected cor-
rectly yet, adjust the image from the computer using the 
menu.  
To move the image horizontally :
Adjust HORIZ. POSITION in the SIGNAL menu.  Press 
the  button to move the image to the left.  Press the  
button to move the image to the right.
To move the image vertically : 
Adjust VERT. POSITION in the SIGNAL menu.  Press 
the  button to move the image upward.  Press the  
button to move the image downward.
When the image  ickers or the image is out of focus :
Adjust FINE SYNC. in the SIGNAL menu.
When the top part of the image  ags :
Change the setting of HOLD in the SIGNAL menu. Se-
lect ON 
, press the ENTER button, and adjust BEGIN 
or END to minimize the fl agging.
When wide strips appear : 
Adjust CLAMP POSITION or CLAMP WIDTH in the SIG-
NAL - USER menu.
Important:
Do not change any of the settings in the SIGNAL-USER 
menu for normal use.
R G BR G B
SIGNAL
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER 
INPUTRGB
FINE SYNC. 0
USER
XGA60opt.
OK
ONHOLD
7.5%
SET UP
CLAMP 
POSITIONUSER
0
CLAMP WIDTH 1
Simple adjustment method
1.  Select HORIZ. POSITION in the SIGNAL menu.
2. Press the  or  button to adjust the horizontal start 
position (or the left side of the image).
3.  Select TRACKING in the SIGNAL menu.
4. Press the  or  button to adjust the horizontal end 
position (or the right edge of the image).
5.  Repeat steps 1 to 4 for optimum adjustment results. 
6.  Select VERT. POSITION in the SIGNAL menu.
7. Press the  or  button to adjust the vertical start 
position (or the upper edge of the image). 
						

							EN - 20
Advanced features
Still
To stop the motion in the image temporarily (or to dis-
play a still image):
Press the STILL button on the remote control.
•  The image will freeze temporarily.
To resume the motion in the image:
Press the STILL button on the remote control again.
Important:
•  Do not display a still picture for a long time because 
the afterimages may persist on the screen.
Page-up and page-down
You can control the computer to page-up and page-
down the presentation data using the remote conjtrol. 
Switch the pages using the PAGE UP or DOWN button 
on the remote control.
Connection
To control the computer using the remote control, con-
nect the projector with the computer as shown below.
•  Only the computers equipped with a USB port are 
supported. 
•  Wait for the lamp to light up before connecting the 
USB cable.
USB
USB cableto USB port USB 4-pin
(type B)
USB 4-pin
(type A)