Mitsubishi Ex100u Projector User Manual

							EN - 21
ENGLISH
PASSWORD
CONFIRM
O K CANCEL
MENU ACCESS
XGA60opt.
LOCK
UNLOCKOK
OK
PASSWORD
O K CANCEL
Password function
This projector is equipped with the password func-
tion that is designed for prevention of wrong operation 
by children and restriction on operation by other than 
specifi ed users.  
MENU ACCESS ............All the buttons except for the 
POWER button on the projector are disabled. (The 
buttons on the remote control are enabled.) You can 
use this mode as a measure of prevention of wrong 
operation by children and restriction on operation by 
other than specifi ed users.
To enable the password function:
1.  Display the FEATURE menu.
2. Press the 
 or  button to select PASSWORD 
FUNCTION.
3.  Press the ENTER button.
•  The screen for setting the password function will 
appear.
•  When the password has already been set, the 
mode won't be changed. In such cases, press the 
ENTER button to cancel the password function 
and try again.  
4.  Press the ENTER button.
• The screen for entering a password will appear. 
5. Press the 
 or  button to select a number from 0 
to 9.
6. Press the  button.
•  You can set the next digit. 
7.  Repeat steps 5 and 6 to set a four-digit password. 
8.  Enter the password again for confi rmation using the 
same steps.
9.  Select OK, and press the ENTER button. 
•  If the entered passwords don't match, an error 
message will appear. 
•  To cancel the procedure, select CANCEL, and 
press the ENTER button. 
•  You can cancel the procedure by pressing the 
MENU button alternatively. To cancel the password function: 
1.  Display the FEATURE menu.
2. Press the 
 or  button to select PASSWORD 
FUNCTION.
3.  Press the ENTER button.
•  The screen for canceling the password function 
will appear.
4.  Press the ENTER button.
•  The screen for entering the password will appear. 
5. Press the 
 or  button to select a number from 0 
to 9.
6. Press the  button.
•  You can set the next digit. 
7.  Repeat steps 5 and 6 to enter the four-digit pass-
word. 
8. Press the  button, select OK, and press the ENTER 
button.
•  If you enter a wrong password, an error message 
will appear.
•  To cancel the procedure, press the  button, 
select CANCEL, and press the ENTER button. 
•  You can cancel the procedure by pressing the 
MENU button alternatively. 
Important:
•  If you forget your password, keep pressing the 
MENU and ENTER buttons on the control panel at 
the same time about three seconds to cancel the 
password function.
MENU ACCESS
XGA60opt.
LOCK
UNLOCKOK
OK 
						

							EN - 22
Lamp replacement
9.  Tighten up the screw (a) using a 
Phillips screwdriver (+) to secure 
the lamp cover.
Reset of the lamp operation time
Plug in the power cord, turn on the 
lamp, and reset the lamp operation time by keep press-
ing the , ,  and POWER buttons on the control panel 
at the same time about three seconds.
Important:
•  Unless these three buttons are pressed at the same 
time, the lamp operation time isnt reset. 
•  Make sure that the STATUS indicator is lit twice and 
the lamp operation time is reset successfully. 
•  The projector doesnt turn on if the lamp cover isnt 
attached securely. 
•  Be sure to reset the lamp operation time whenever 
you replace the lamp. 
•  Do not reset the lamp operation time unless you 
replace the lamp. 
Caution:
•  The lamp is fragile. If it is broken, be careful not to 
cut yourself with glass fragments.
•  Contact your dealer for a new lamp.
Interval of lamp replacement
The recommended interval of lamp replacement is 
about 3000 - 5000 hours of consecutive use. Such 
interval differs depending on the operating environment 
and may be shorter. Decrease in luminescence and/or 
color brightness indicates that the lamp needs to be 
replaced. When the lamp operation time exceeds the 
time elapsed until the lamp shutdown notice*
1 is is-
sued, the indicator will blink alternately green and red 
while the lamp is lit (while the lamp is not lit, the indica-
tor will blink red only) and the lamp replacement mes-
sage will appear on the screen for one minute every 
time the lamp is turned on. When the lamp operation 
time exceeds the time elapsed until the lamp shutdown 
warning*
2 is issued, the replacement message (LAMP 
EXCHANGE) will appear on the screen for one minute at 
fi xed intervals*
4 thereafter. 
When the lamp operation time exceeds the time 
elapsed until the lamp shutdown*
3, the projector auto-
matically shuts off and cant be used until the lamp is 
replaced and the lamp operation time is reset. 
(a) (b)
(c)
When the lamp no longer functions, replace it with a 
new one.
Caution:
•  Do not remove the lamp immediately after using the 
projector.  You may get burned because the lamp is 
very hot after use.
•  Before replacing the lamp, press the POWER button 
to turn off the lamp and wait for two minutes for the 
lamp to cool down. Unplug the power cord from the 
wall outlet and wait one hour for the lamp to cool 
down completely. 
•  Do not remove the lamp except for replacement. 
Careless handling can cause injury or fi re.
•  Do not touch the lamp directly. It may break and 
cause injury or burn.
•  Be sure not to drop the lamp lid screw into the 
projector. Also be sure not to put metal or any 
fl ammable objects inside because it may cause fi re 
or electric shock. If any objects should fall inside, 
unplug and contact your dealer.
•  Install the lamp securely to prevent failure and fi re.
•  If the lamp should break, small glass fragments may 
fall out through the grilles and some may remain 
inside of the projector or the lamp box. When taking 
the lamp box out, be sure to turn over the projector 
and hold the handle of the lamp box to avoid injury 
due to the glass fragments.
•  If the lamp should break, never shake the lamp box 
or hold it in front of your face after removing it. The 
glass fragments may fall out and cause injury to your 
eyes.
•  When placing the projector upside down to replace 
the lamp or conduct maintenance, ensure that the 
projector is securely placed before working with it.
1.  Reverse the projector gently.
2.  Loosen the screw (a) using a 
Phillips screwdriver (+), and 
remove the lamp cover (b).
3.  Loosen the screws (c) using a 
Phillips screwdriver (+).
4.  Pull up the handle.
5.  Pull out the lamp box by the handle 
while holding the projector.
•  Pull the lamp box out of the 
projector slowly. If it is pulled 
out quickly, the lamp may break 
scattering glass fragments. 
•  Do not spill liquid on the removed 
lamp box or do not place it near 
any fl ammable object or where 
children can reach to prevent 
injury or fi re.
6.  Load a new lamp box securely into the 
projector in the right orientation.
7.  Put the handle back to the original posi-
tion.
•  Make sure that the handle is locked.
8.  Tighten up the screws (c) using a Phillips 
screwdriver (+).(c)
 EX100U  ES100U
*1   2250 Hours  3750 Hours
*2   2850 Hours  4750 Hours
*3   3000 Hours*5 5000 Hours*5
The times above are when LAMP MODE of the INSTALLATION 
menu is set to LOW. When it is set to STANDARD, this duration 
will be shortened.
*4  These intervals vary depending on the lamp mode 
setting. 
*
5  When LAMP MODE is set to STANDARD, the time 
elapsed until the lamp shutdown will be shortened to 
2000 hours.
Caution:
•  This projector uses a lamp that contains mercury. 
Disposal of the lamp or the projector with the lamp 
may be regulated due to environmental consider-
ations. For disposal or recycling information, please 
contact your local authorities or the Electronic Indus-
tries Alliance: www.eiae.org. (For US only). 
						

							EN - 23
ENGLISH
Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult this 
chart before contacting your dealer.
Images arent projected on the screen.
Problem
Power isn't turned on.
Images aren't projected on 
the screen.
Images suddenly disap-
pear. 
"NO SIGNAL" is displayed.
Cause and solution
• Check the states of the indicators.
POWER
Off
Steady red
Blinking red 
/ green
STATUS
Off
Off
Blinking 
orange
Blinking 
green
Steady red
Off
Steady
or
Blinking
  Solution
•  Connect the power cord to the projector. 
•  Plug the power cord into a wall outlet. 
•  If any objects are blocking the air inlet or outlet grille, remove them and carry out 
the following.
1.  Unplug the power cord from the wall outlet.
2.  Make sure that the projector has cooled off. 
3.  Plug the power cord into the wall outlet.
4.  Press the POWER button.
•  If any objects are blocking the air inlet or outlet grille, remove them.
•  Don't expose the air outlet grilles to hot air emitted from a heating appliance.
•  After the STATUS indicator stops blinking, press the POWER button.
•  If you unplug the power cord while the fan is rotating, the lamp may not turn on about 
one minute when you plug the power cord next time. 
•  The lamp can't turn on again for one minute after it goes out. 
•  Press the POWER button several times.
•  Replace the lamp. (The lamp is at the end of its life.)
•  Attach the lamp cover on the bottom.
•  Unplug the power cord from the wall outlet and contact your dealer.
• Cancel the AV mute by pressing the MUTE button.
• Remove the lens cap.
• The lamp sometimes takes about one minute to light up.
• On rare occasion, the lamp fails to light up. In such cases, wait a few minutes and try to light 
the lamp again. 
• If the projector was turned off before the lamp cooled down completely, the fans may start 
rotating and the POWER button may not function when you plug the power cord into the wall 
outlet next time. Wait for the fans to stop and press the POWER button to turn on the lamp 
again. 
• Check that the lamp cover are closed. 
• Check that the cable connected to the external device isn't broken. 
• When an extension cord is being used, replace it with the supplied cable and check whether 
images are projected correctly. If images are projected correctly, use an RGB signal amplifier 
along with the extension cord. 
• The air inlet or outlet grille may be blocked. (In such cases, the STATUS indicator blinks orange.) 
 Remove the objects blocking the air inlet or outlet grille and carry out the following. 
1.  Wait for the air inlet or outlet fan to stop (or wait for the STATUS indicator to go out.)
2.  Unplug the power cord from the wall outlet.
3.  Wait about 10 minutes.
4.  Plug the power cord into the wall outlet.
5.  Press the POWER button.
• When the STATUS indicator is blinking red, it is indicating that the lamp should be replaced. 
Replace the lamp in this case. 
• Turn on the power of the connected device, or check whether there is something wrong with 
the connected device.
• Check whether the external device outputs signals. (Check this especially when the external 
device is a notebook computer.) 
• Check that the cable connected to the external device isn't defective. 
• Check that the projector is connected to the external device using the correct terminals. 
• Check that the connected device is correctly selected as the input source. 
• When an extension cord is being used, replace it with the supplied cable and check whether 
images are projected correctly. If images are projected correctly, use an RGB signal amplifier 
along with the extension cord.  
						

							EN - 24
Troubleshooting (continued)
Images arent projected correctly.
Problem
Projected images are 
shaking.
Projected images are dis-
placed. 
Projected images are dis-
torted.
Projected images are dark. 
Projected images are 
blurred. 
White dots are seen on 
projected images.
Black dots are seen on 
projected images.
Rainbow blur appears in 
projected images. 
Fine streak pattern ap-
pears in projected images.
Projected images (and/or 
audio) appear wavy and 
distorted. 
Tint in projected images is 
incorrect.
Only the motion areas in 
the images supplied from 
the computer aren't dis-
played. 
Projected images are ob-
scured.
Cause and solution
• Check that the cable connected to the external device isn't intermittent. 
• Connect the cable's plug with the external device's connector firmly.
• Press the AUTO POSITION button.
• Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See page 
19.)
• Adjust the projector and the screen so that they are perpendicular to each other. (See page 12.)
• Adjust BRIGHTNESS in the IMAGE menu. (See page 18.)
• Replace the lamp. (See page 22.)
• Adjust the focus. (See page 13.)
• Clean the lens.
• Press the  or  button on the remote control to eliminate flicker. 
• Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 18.)
• Adjust the projector and the screen so that they are perpendicular to each other. (See page 12.)
• This symptom is normal for a DLP projector and is not a malfunction. (A very small number of pixels 
may stay lit or out, but such sympton is not a malfunction. Pixels of 99.99% or more are effective.)
• This is due to color breaking noise that occurs in a DLP system and is not a malfunction.
• It occurs because of interference with the screen and isn't a product malfunction. Change the screen 
or readjust the focus of the projector.
• Connect the cable's plug with the external device's connector firmly.
• Keep the projector away from equipment generating interfering radio waves.
• When the keystone adjustment is carried out, the image may not be displayed correctly because of 
the type of input signal. This isn't a product malfunction. In this case, readjust the keystone so that 
the amount of keystone correction is as small as possible.
• Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 17.)
• Check that the cable connected to the external device isn't broken. 
• This is caused by the computer being used. Contact the manufacturer of your computer.
• Match the output resolution of your computer with the resolution of the projector.  For the method to 
change the output resolution of the computer, contact the manufacturer of your computer. (See page 
29.)
• Some images and texts appear obscured during the keystone adjustment. In such cases, use the 
projector without applying the keystone adjustment. (See page 12.) 
						

							EN - 25
ENGLISH
Others
Cause and solution
• This air comes out as a result of cooling the inside of the projector. This isn't a product malfunc-
tion. 
• Check that the volume isn't set to low. 
• The microcomputers inside the projector may be wrongly operating because of noise. 
 Press the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait 
about 10 minutes, plug the power cord in, and try again.
• This indication appears when the ambient temperature rises high. When the ambient tempera-
ture stays high, the lamp goes out.
 Eliminate any causes of the rise in the ambient temperature.
• This indication appears when the air inlet or outlet grille is blocked. When they are kept blocked, 
the lamp goes out. 
 Remove the objects blocking the air inlet or outlet grille. 
• This mark appears when ineffective operation is carried out. This isn't a product malfunction. 
• Check that the battery is loaded in the remote control or the battery isn't weak. (See page 8.)
• Check that the remote control sensor isn't exposed to direct sunlight or fluorescent light. (See 
page 8.)
• Use the remote control within its operation range. (See page 8.)
• Use the remote control at least 10 cm away from the projector. 
• The password functionis working. 
 Cancel the password lock . (See page 21.)
• Because the color wheel spins at a high speed, metalic sounds may be heard in rare occations. 
Such sympton is not a malfunction.
When the problems below occur after the lamp is replaced, check the following. 
Problem
The power isn't turned 
on. 
The STATUS indicator 
blinks.
Problem
Hot air is emitted from the 
air outlet grilles. 
No audio is output. 
The menu can't be used. 
TEMPERATURE!! is dis-
played.
The 
 mark appears. 
The remote control doesn't 
function easily or at all.
The buttons on the control 
panel (except for the 
POWER button) don't 
function. 
Cause and solution
• Attach the lamp cover on the bottom correctly. 
• Reset the lamp operation time. (See page 22.)
• Reset the lamp operation time. (See page 22.)
Maintenance
Caution:
Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on 
the projector. 
Cleaning of the projector and the ventilation slots
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft 
cloth dampened with diluted mild detergent, and then wipe them with a dry cloth.
To protect the surface of the projector from fading or deteriorating:
•  Do not spray insecticide on or inside the projector.
•  Do not use benzine or thinner to clean it.
•  Do not let rubber or plastic materials contact with projector.
Cleaning of the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fl uid. The lens surface is 
fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fi ngers.
Abnormal sound is heard. 
						

							EN - 26
Indicators
POWER STATUS
POWER
Steady 
red
Steady 
green
Steady 
green
STATUS
Off
Blinking 
green
Steady 
green
CONDITION
Stand-by
Lamp stand-by (about 1 minute)
The power is on. (Normal condition)
NOTE
The POWER button cannot be used to
switch between on and off.
POWER
Steady 
green
or
Steady red
Steady red
Steady 
green
Steady red
Steady red
Blinking 
green/red
Blinking 
green/red
STATUS
Blinking orange
Blinking green
Blinking green/red
Blinking red
Steady red
Off
Steady
or
Blinking
CONDITION
Abnormal temperature
•  The ventilation grilles is clogged with dust or dirt.
•  The room temperature is high.
The protection circuit is working or the lamp is in an
abnormal condition. 
The lamp operation time exceeds the time elapsed until the 
lamp shutdown notice while the power is on. (See page 22.)
The lamp operation time exceeds the time elapsed until the 
lamp shutdown notice while the power is off. (See page 22.)
The lamp operation time exceeds the time elapsed until the 
lamp shutdown. (See page 22.)
The lamp cover isn’t closed. 
Abnormal.POSSIBLE SOLUTION
•  Clean the ventilation grilles.
•  Relocate the projector to a cooler place.
•  Wait until the STATUS indicator goes out, 
then press the POWER button.
•  If the above solution is not effective, replace 
the lamp.
Replace the lamp.
Change with a new lamp if this problem recurs.
Close the cover correctly.
Contact your dealer.
This projector has two indicators, each of which shows the operation condition of the projector. 
The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your 
dealer. 
Normal condition
Abnormal condition
POWER indicator
STATUS indicator  
						

							EN - 27
ENGLISH
Speci cations
Ty p e
Model
Rated power supply
Rated input
Display Technology
Colors
Projection lens
Light source lamp
Picture size
PC compatibility
Video compatibility
Speaker
S-video input
Video input
Audio input
Analog RGB input
Control connector
Outside dimensions
Weight
Length of power cord
Temperature, humidity
(performance guaranteed)DLP™ DATA projector
EX100U / ES100U
100 - 240 V  AC,  50 / 60 Hz
2.9 A (EX100U) / 3.5 A (ES100U)
0.7-inch Single chip Digital Micromirror Device (DMD) with R,G,B,W color wheel
Pixels  1024 x 768 = 786432 pixels (EX100U)
Pixels  800 x 600 = 480000 pixels (ES100U)
16770000 colors
F 2.4- 2.6  f = 23 - 27.6 mm (EX100U) / F 2.4- 2.7  f = 19 - 23 mm (ES100U)
200 W (EX100U) / 250 W (ES100U)
40 - 300 inch (aspect ratio 4:3)
Resolution:640x400 (Expand) - 1024x768 (Real) - 1280x1024 (Compress) (EX100U)
Resolution:640x400 (Expand) - 800x600 (Real) - 1024x768 (Compress) (ES100U)
Sync on Green available
NTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM, PAL-60
Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p)
2 W Mono, Round type ø4.5 cm x 1
Luminance signal: 1.0 Vp-p 75 Ω    (negative sync.)
Chroma signal: 0.286 Vp-p 75 Ω  (burst signal)
1.0 Vp-p  75 Ω   (negative sync.)
350 mVrms,  10 kΩ or more 
RGB: 0.7 Vp-p  75 Ω (negative sync.) 
YP
BPR/YCBCR :  Y:1.0 Vp-p (negative sync.)  PBPR/CBCR:0.7 Vp-p
HD/CS : TTL level (positive or negative)
VD : TTL level (positive or negative)
Serial (8-pin, RS-232C standards) 
USB terminal 
310 x 100 x 245 mm (width x height x depth)  Not included protrusion.
Approx.  2.9 kg    
114 inch (2.9 m)
+41ºF (+5ºC) - +95ºF (+35ºC),  30 - 90%
 The speci cations and outside appearance of the projector are subject to change without prior notice.
Kensington Lock
This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. 
Refer to the information that came with the Kensington System for instructions on how to use it to secure the projec-
tor. Please contact Kensington Technology Group below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone : +1- (650)572-2700  Fax : +1- (650)572-9675 
						

							EN - 28
Connectors
 1  R(RED)/CR 2 G(GREEN)/Y 3 B(BLUE)/CB 4  GND
  5  GND   
  6  GND   
 7  GND
  8  GND    
 9  DDC5V
 10  GND 
 11  GND 
 12  DDC Data
 13  HD/CS
 14  VD
 15  DDC Clock
 1  TXD  IN
 2  -  - 
 3  -  -
  4  GND    - 
 5  5V  IN
 6  CLOCK  OUT
 7  RXD  OUT 
 8  DATA  OUT
1
352
681 5
116 10
15
61
245
310
100 5
SERIAL (8-pin)
 
pin No.  Name  I/O
COMPUTER / COMPONENT VIDEO IN/OUT
(Mini D-SUB 15-pin)
 Pin No.  Spec.
Dimensional drawings  (unit : mm)
    Whats included in the box
2 AC power cord  246C483-10
    246C383-20
1 Audio/Video cable  246C381-10
1   RGB cable for PC  246C521-10
1 RS-232C cable  246C508-10
1 USB cable  246C509-101   Remote control  290P131-10
1 Quick Start up  857D064-40
1 Safety manual  871D421-20
1 CD-ROM  919C137-20
1 Carrying case  772P044-10
2 Battery  –
Replacement part(Option / Not included in the box)
   Spare lamp (for EX100U)  499B042-10
   (VLT-EX100LP)
IN
 1  R(RED)/CR 2 G(GREEN)/Y 3 B(BLUE)/CB 4  -
  5  GND   
  6  GND   
 7  GND
  8  GND    
 9  -
 10  GND 
 11  -
 12  -
 13  HD/CS
 14  VD
 15
 -  Pin No.  Spec.
OUT
Speci cations (continued)
Spare lamp (for ES100U)  499B041-10
   (VLT-XD400LP) 
						

							EN - 29
ENGLISH
 TV60, 480i(525i) -  15.73  59.94  1024 x 768  800 x 600 
  TV50, 576i(625i)  -  15.63  50.00  1024 x 768  800 x 600 
  1080i 60 (1125i 60)  -  33.75  60.00  1024 x 576  800 x 450 
  1080i 50 (1125i 50)  -  28.13  50.00  1024 x 576  800 x 450 
  480p (525p)  -  31.47  59.94  1024 x 768  800 x 600 
  576p (625p)  -  31.25  50.00  1024 x 768  800 x 600 
  720p 60 (750p 60)  -  45.00  60.00  1024 x 576  800 x 450 
  720p 50 (750p 50)  -  37.50  50.00  1024 x 576  800 x 450 
  PC98  640 x 400  24.82  56.42  1024 x 640  800 x 500 
  CGA84  640 x 400  37.86  84.13  1024 x 640  800 x 500 
  CGA85  640 x 400  37.86  85.08  1024 x 640  800 x 500 
  VGA60  640 x 480  31.47  59.94  1024 x 768  800 x 600 
  VGA72  640 x 480  37.86  72.81  1024 x 768  800 x 600 
  VGA75  640 x 480  37.50  75.00  1024 x 768  800 x 600 
  VGA85  640 x 480  43.27  85.01  1024 x 768  800 x 600 
  SVGA56  800 x 600  35.16  56.25  1024 x 768  800 x 600
  SVGA60  800 x 600  37.88  60.32  1024 x 768  800 x 600 
  SVGA72  800 x 600  48.08  72.19  1024 x 768  800 x 600
  SVGA75  800 x 600  46.88  75.00  1024 x 768  800 x 600
  SVGA85  800 x 600  53.67  85.06  1024 x 768  800 x 600
  XGA60  1024 x 768  48.36  60.00  1024 x 768  800 x 600 
  XGA70  1024 x 768  56.48  70.07  1024 x 768  800 x 600
  XGA75  1024 x 768  60.02  75.03  1024 x 768  800 x 600
  XGA85  1024 x 768  68.68  85.00  1024 x 768  800 x 600
  SXGA70a  1152 x 864  63.85  70.01  1024 x 768  - 
  SXGA75a  1152 x 864  67.50  75.00  1024 x 768  - 
  SXGA60b  1280 x 960  60.00  60.00  1024 x 768  - 
  SXGA60  1280 x 1024  63.98  60.02  960 x 768  - 
  MAC13  640 x 480  35.00  66.67  1024 x 768  800 x 600 
  MAC16  832 x 624  49.72  74.55  1024 x 768  800 x 600
  MAC19  1024 x 768  60.24  75.02  1024 x 768  800 x 600 
  MAC21  1152 x 870  68.59  74.96  1016 x 768  - 
  HP75  1024 x 768  62.94  74.92  1024 x 768  800 x 600 
  SUN66a  1152 x 900  61.85  66.00  984 x 768  - 
  SUN76a  1152 x 900  71.81  76.64  984 x 768  -
Speci cation of RGB signals in each computer mode of the projector 
 Signal mode  resolution  horizontal  vertical  EX100U  ES100U
     (H x V)  frequency (kHz)  frequency (Hz)  (H x V)  (H x V)
Important:
•  Some computers aren't compatible with the projec-
tor.
•  The projector's maximum resolution is 1024 x 768 
pixels (800 x 600 pixcels for ES100U).  It may not 
display images of higher resolutions than 1024 x 768 
(or 800 x 600) correctly.
•  Images with SYNC on G (Green) signal may jitter.
•  Images with SYNC on G (Green) signal may be 
tinged with green.
•  If the resolution and frequency of your computer 
aren't shown on the table, fi nd the compatible reso-
lution and frequency by changing the resolution of 
your computer. •  Set COMPUTER INPUT in the SIGNAL menu to RGB 
when inputting the HDTV signal as RGB signal.
•  TV60 and TV50 are equivalent to 480i and 576i 
respectively. When these signals are supplied to the 
VIDEO or S-VIDEO signal, the signal mode is indicat-
ed as TV60 or TV50. When they are supplied to the 
COMPONENT terminal, the signal mode is indicated 
as 480i or 576i.  
						

							North America
MESCA (Mitsubishi Electric Sales Canada Inc.)
http://www.mitsubishielectric.ca
Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2, 
Canada
Sales Phone :+1-(905) 475-7728
 Fax :+1-(905) 475-7958
 E-mail :[email protected]
Technical Phone :+1-(905) 475-7728
 Fax :+1-(905) 475-7958
Customer Care
 E-mail :[email protected]
MDEA (Mitsubishi Digital Electronics America, Inc.)
(Warranty Registration)
http://www.mitsubishi-presentations.com/
Presentation Products Division, 9351 Jeronimo Road, Irvine, CA 92618 U.S.A
Phone  Main Line  :+1-(949) 465-6000
 Technical  :+1-(888) 307-0309
  Product Information  :+1-(888) 307-0312
Technical Support 
E-mail :[email protected]      
Europe
MEU-FRA (Mitsubishi Electric Europe B.V French Branch)
25, Boulevard des Bouvets 92 741, Nanterre CEDEX, France
Sales  Phone  :+33 (0)1 55-68-55-07
 Fax :+33 (0)1 55-68-57-31
Technical  Phone  :+33 (0)1 41-02-83-24
 Fax :+33 (0)1 49-01-07-23
MEU-GER (Mitsubishi Electric Europe B.V. German Branch)
http://www.mitsubishi-evs.de/
Gothaer Strasse 8, 40880 Ratingen, Germany
MEU-IR (Mitsubishi Electric Europe B.V. Irish Branch)
http://www.mitsubishi.ie/
Westgate Business Park, Ballymount, Dublin 24, Ireland
Sales Phone :+353-(0)1- 4198844
 Fax :+353-(0)1-4564422
Technical Phone :+353-(0)1-4198807
 Fax :+353-(0)1-4198895
MEU-IT (Mitsubishi Electric Europe B.V. Italian Branch)
Centro Direzionale Colleoni, Palazzo Persero-Ingresso 2, Via Paracelso 12, 20041 
Agrate Brianza, Italy
Sales Phone :+39-(0)39-60531
 Fax :+39-(0)39-6053214
 E-mail  :[email protected]  
MEU-NL (Mitsubishi Electric Europe B.V. Benelux Branch)
http://www.mitsubishi.nl/LCD/ProdFrame.html
Nijverheidsweg 23a, 3641 RP Mijdrecht, The Netherlands   
Sales Phone :+31-297-282461
 Fax :+31-297-283936
 E-mail :[email protected]
Technical Phone :+31-297-282461
 Fax :+31-297-283936
 E-mail :[email protected] 
MEU (MITSUBISHI ELECTRIC EUROPE B.V.)
http://www.mitsubishi-projector.ru/
Moscow Representative Offi ce, 12/1 Goncharnaya St. 109240, Moscow, Russia
Sales  Phone  :+7 (095) 915 8602
  Fax  :+7 (095) 915 8603
MEU-SP (Mitsubishi Electric Europe B.V. Spanish Branch)
http://www.mitsubishielectric.es/
Ctra. de Rubi, 76-80, 08190 Sant Cugat del Valles, Barcelona, Spain
Sales Phone :+34-93.565.31.54
 Fax :+34-93.589.43.88
 E-mail :[email protected]
Technical Phone :+34-93.586.27.51
 Fax :+34-93.699.74.45
 E-mail :[email protected]
MEU-SWE (Mitsubishi Electric Europe B.V Scandinavian Branch)
Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden
Sales Phone :+46-(0)8-6251070
 Fax :+46-(0)8-6251036
Technical Phone :+46-(0)8-6251052
 Fax :+46-(0)8-6251036
MEU-UK (Mitsubishi Electric Europe)
http://www.mitsubishi.co.uk/evs/
Visual Information Systems Division, Travellers Lane, Hatfi eld, Hertfordshire, AL10 
8XB
Sales  Phone  :+44 (1707) 278684
 Fax :+44 (1707) 278541
 E-mail :[email protected]
Technical  Phone  :+44 (870) 606 5008
 Fax :+44 (1506) 431927
 E-mail :[email protected]
Russia (Mitsubishi Electric Europe B.V Moscow Representative Offi ce)
52, bldg.5, Kosmodamianskaya Nab, 113054, Moscow, Russian Federation
Sales  Phone  :+7 (095) 721 2070
  Fax  :+7 (095) 721 2071   
Technical  Phone  :+7 (095) 721 2070
  Fax  :+7 (095) 721 2071     
MITSUBISHI Projector Contact Information
AsiaMITSUBISHI ELECTRIC RYODEN AIR-CONDITIONING &
VISUAL INFORMATION SYSTEMS (HONGKONG) LTD.
•  Hong Kong Offi ce
  Units 5-10, 20/F., Ever Gain Plaza, Tower One
  88 Container Port Road, Kwai Chung, New Territories,Hong Kong.
  Technical  Support
 Phone  :+852 2510 0777
  Fax  :+852 2510 0463
• Beijing Offi ce
 9/F, Offi ce Tower 1, Henderson Centre, 18 Jianguomennei Dajie, Dongcheng Dis-
trict, Beijing, 100005, China
  Sales & Technical  Support
  Phone  :+86 (10) 6518 2930
  Fax  :+86 (10) 6518 2530
• Shanghai Offi ce
  10/F, Shanghai Square Offi ce Tower, 138 Huai Hai Zhong Road, Lu Wan District, 
Shanghai, 200021, China
  Sales & Technical  Support
  Phone  :+86 (21) 6327 2228
  Fax  :+86 (21) 6327 4918
• Shenzhen Offi ce
  Unit 01-04, 13/F, Building A, Tian An International Building, Renmin Road South, 
Shenzhen, 518005, China
  Sales & Technical  Support
  Phone  :+86 (755) 518 6386
  Fax  :+86 (755) 218 4775
• Chengdu Offi ce
  Block B-1, 23/F., Chuan Xin Mansion, 18 Section 2, Renmin Road South, Chengdu, 
610016, China
  Sales & Technical  Support
  Phone  :+86 (28) 619 9730
  Fax  :+86 (28) 619 9801
MEAP (Mitsubishi Electric Asia Pte Ltd)
http://www.mitsubishielectric.com.sg
307 Alexandra Road, Mitsubishi Electric Building, 289245,Singapore
Main Line  Phone  :+65 6 473 2308
  Fax  :+65 6 475 9503
Sales & Technical Support
E-mail :[email protected]
AMS (Antah Melco Sales & Services Sdn Bhd 
(A Joint-Venture Company of Mitsubishi Electric Corporation))
http://www.antahmelco.com.my
6, Jalan 13/6, Petaling Jaya, Selangor Darul Ehsan, Malaysia
Main Line  Phone  :+603-7955 2088
 Fax :+603-7956 3950
  :+603-7958 2576
Technical Support 
Phone :+603-7955 2088
E-mail :[email protected]
Product Information
Phone :+603-7955 2088
ME-TWN (Mitsubishi Electric Taiwan Co., Ltd.)
http://www.mitsubishi-electric.com.tw
9th Floor., 90 Sec. 6, Chung Shan N. Rd., Taipei, Taiwan
Sales Support  Phone  : +886 (0) 2 2832 8255
  Fax  : +886 (0) 2 2833 9813
KYW (Kang Yong Watana Co., Ltd.)
http://www.mitsubishi-kyw.in.th
28 Krungthep Kreetha Road, Huamark Bangkapi, Bangkok, 10240, Thailand
Sales Support  Phone  :+66 (2) 731 6901
  Fax  :+66 (2) 379 4763
STC (Setsuyo Astec Corp. Seoul Branch)
Dongseo Game Channel Bldg, 660-11, Deungchon-dong, Kangseo-ku, Seoul, Korea
Main Line  Phone  :+82 (0) 2 3665 4964
  Fax  :+82 (0) 2 3665 4965
Oceania
ME-AUST (Mitsubishi Electric Australia)
http://www.mitsubishi-electric.com.au/prod.asp?prod=proj
348 Victoria Road, Rydalmere, N.S.W. 2116, Australia
Sales Phone :+(612)9684-7777
 Fax :+(612)9898-0484
 E-mail :[email protected]
BDT (Black Diamond Technologies Ltd.)
(Warranty Registration)  http://www.bdt.co.nz/projectors/warranty.asp
1 Parliament St, Lower Hutt, Wellington, New Zealand
Sales Phone :+64-(0)4-560-9100
 Fax :+64-(0)4-560-9133
 E-mail :[email protected]  
Technical Phone :+64-(0)4-560-9100
 Fax :+64-(0)4-560-9133    
 
Manufactured by Mitsubishi Electric Corporation
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan
MITSUBISHI ELECTRIC CORPORATION