Mitsubishi Xd211u Data Projector User Manual
Have a look at the manual Mitsubishi Xd211u Data Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 561 Mitsubishi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
EN-21 ENGLISH Troubleshooting Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be sure to unplug the power plug, and then contact your dealer. No image appears on the screen. ProblemSolution Power can not be turned on.• Check whether the indicators are on or off and how they are lightning. No image appears on the screen.• Cancel the AV mute by pressing the AV MUTE button. • Check that the lens cap is removed. • It may take about 1 minute for the lamp to light up. • The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again. • If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotat- ing and the ON button may not work after the power cord is plugged. After the fan stops rotating, press the ON button to turn back on the POWER indicator. • Check that the intake vent is clean. • Check that the lamp cover is closed.(See page 20.) • Check that the cables connected to the external devices are not broken. • When an extension cable is being used, replace it with the supplied cable for check. • When images are displayed correctly, add an RGB signal amplifier to the extension cable. • When the menu is turned on and the signal is lost or not input, the system will not search for the signal even if the signal is input again. In this case, turn off the menu. Power turns off.• This problem may occur when the intake vent and/or exhaust vents are blocked. (For example: the STATUS indicator brinks red.) JRemove the objects blocking the intake vent and/or exhaust vents and then carry out the following proce- dure. 1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the POWER indicator lights green.) 2. Unplug the power cord from the wall outlet. 3. Wait about 10 minutes. 4. Plug the power cord into the wall outlet. 5. Press the ON button. • When the POWER indicator is steady amber, it is indicating that the lamp should be replaced. Replace the lamp in this case. • If the lamp has deteriorated, it may go out after a while it illuminates. • Check if the Auto power off function is set. No Signal is displayed.• Turn on the power of the connected device, or check whether there is something wrong with the connected device. • Check whether the external device output signals. (Check this especially when the external device is a note- book computer.) • Check that the cable connected to the external device isn’t defective. • Check that the projector is connected to the external device using the correct terminals. • Check that the connected device is correctly selected as the input source. • When an extension cord is being used, replace it with the supplied cable and check whether images are pro- jected correctly. If images are projected correctly, use an RGB signal amplifier along with the extension cord. Off Steady green Blinking red Blinking green Blinking green Steady green Off Off Steady amber Steady green Blinking greenBlinking red POWER STATUS Solution
EN-22 Troubleshooting (continued) Images are not displayed correctly. ProblemSolution Projected images are shaking. Projected images are displaced.• Check that the cable connected to the external device isn’t intermittent. • Connect the cable’s plug with the external device’s connector firmly. • Press the AUTO POSITION button. • Some computers output out-of-spec signals on rare occasion. Adjust the Computer Image menu. (See page 17.) Projected images are distorted. • Adjust the projector and the screen so that they are perpendicular to each other. (See page 9.) Projected images are dark.• Adjust Brightness and Contrast in the Picture menu. (See page 16.) • Replace the lamp. (See page 20.) Projected images are blurred.• Adjust the focus. (See page 13.) • Clean the lens. • Adjust Tracking and Fine sync. in the Computer Image menu. (See page 17.) • Adjust Brightness and Contrast in the Picture menu. (See page 16.) • Adjust the projector and the screen so that they are perpendicular to each other. (See page 9.) Afterimages persist on the screen.• This phenomenon is improved by keeping projecting an evenly bright image. (Such image burn-in phenom- enon where afterimages persist on the screen may occur if a stationary image is kept displayed on the screen for a long time.) White dots are seen on projected images. Black dots are seen on projected images.• This phenomenon is normal for a DLP projector and is not a malfunction. (A very small number of pixels may visibly or invisibly be persistent all the time, but they are not a sign of system malfunctions. Over 99.99% of the pixels are effective.) Fine streaks are seen on projected images.• This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus a little. • Vertical or horizontal streak noise may appear on the projected image, it may depend on the type of the DVD player, game console or computer you use. Projected images become wavy.• Connect the plugs of the cables to external devices securely. • Keep the projector away from equipment generating interfering radio waves. • When the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input signal. This isn’t a product malfunction. In this case, readjust the keystone so that the amount of key- stone correction is as small as possible. Hue is not appropriate. • Check that the cables connected to the external devices are not broken. Tint in projected images is incorrect.• Check that Signal Type in the Setting menu is correctly set. (See page 18.) • Check that the cable connected to the external device isn’t broken. Different color tint.• When comparing images projected by two projectors, tints in the displayed images may be different because of variation between their optical components. This is not a malfunction. • When comparing the image projected by this projector with those displayed on the television or PC monitor, tints in the displayed images may be different because of difference in the range of color reproducibility. This is not a malfunction. Only the motion areas in the images supplied from the computer aren’t displayed.• This is caused by the computer being used. Contact the manufacturer of your computer. Projected images are obscured.• Match the output resolution of your computer with the resolution of the projector. For the method to change the output resolution of the computer, contact the manufacturer of your computer. (See page 27.) • Some images and texts appear obscured during the keystone adjustment. In such cases, use the projector without applying the keystone adjustment. (See page 12.) Projected images are flickering• After the ON button on the remote has been pressed, or the Lamp mode setting has changed, images may be flickering until the lamp lights stably. This is an expected behavior. • When selecting the input signal, AUTO POSITION and Image in Menu, the projected image may be flicker- ing temporarily. This is not a product malfunction.
EN-23 ENGLISH Troubleshooting (continued) Others If the following problem occurs after the lamp is replaced, check the following first. Maintenance Warning:Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body and lens. Flammable substances may ignite causing fire or breakdown while the lamp is illuminating. Caution: Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector. Cleaning of the projector and the ventilation slots Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened with diluted mild detergent, and then wipe them with a dry cloth. To protect the surface of the projector from fading or deteriorating: • Do not spray insecticide on or inside the projector. • Do not use benzin or thinner to clean it. • Do not let rubber or plastic materials contact with projector. Cleaning of the lens Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fingers. ProblemSolution The exhaust vents emit warm air. • This air comes out after cooling the inside of the projector. You may feel hot, but this is not a malfunction. No audio is output. • Check that the volume isn’t set to low. The menu can’t be used.• The microcomputers inside the projector may be wrongly operating because of noise. JPress the ON button to turn off the lamp and unplug the power cord from the wall outlet. Wait about 10 minutes, plug the power cord in, and try again. The remote control doesn’t function easily or at all.• Check that the battery is loaded in the remote control or the battery is not weak. (See page 8.) • Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent light. (See page 8.) • Use the remote control within its operation range. (See page 8.) Abnormal sound is heard.• Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions. Such symp- tom is not a malfunction. ProblemSolution The projector does not turn on. • Fit the lamp cover securely. (See page 20.) The POWER lights amber and the STATUS lights green.• Reset the lamp operating time. (See page 20.)
EN-24 Indicators This projector has two indicators, each of which shows the operation condition of the projector. The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your dealer. Normal condition Abnormal condition POWERSTATUSCONDITIONNOTE Stand-by The projector is in good condition. The projector is shutting and the fan motor is cooling the lamp for shutdown. Do not unplug the power cord or turn the power off before the POWER LED changes to flashing. The fan motor will turn off when the lamp has been cooled. STATUS indicator POWER indicator Blinking green Off Steady green Steady green Steady amberSteady amber POWERSTATUSCONDITIONPOSSIBLE SOLUTION The projector system has some problems with its fan, so the pro- jector cannot start up.Contact your dealer. The lamp has reached its end of life and must be changed soon. The lamp will continue to operate until it fails. Change the lamp. If the lamp is off, then the ballast will become malfunction. (during power on)Replace the lamp and reset the lamp operation time. Temperature is too high. The lamp will turn off. The fan motor is cooling the lamp.Wait until the lamp cools down, and the projector enters stand-by mode. The lamp ignition failed. Replace the lamp and reset the lamp operation time. Temperature is too high or temperatures sensor is error during stand-by mode.• Wait for 1 hour until the lamp cools down, and turn the power back on. • If the temperature is still high after 1 hour, con- tact your dealer. Steady greenBlinking green Steady amber Steady green Steady greenBlinking red Steady amber Off Blinking greenBlinking red
EN-25 ENGLISH Specifications • The specifications and outside appearance of the projector are subject to change without prior notice. Type DLP™ DATA projector Model XD211U Rated power supply 100 - 240 V AC, 50 / 60 Hz Rated input 2.5 A Display Technology0.55-inch Single chip Digital Micromirror Device (DMD) Pixels 1024 x 768 = 786432 pixels Colors 16770000 colors Projection lens F 2.5 - 2.7, f = 19.9 - 23.9 mm Light source lamp 180 W Picture size 40 - 300 inch (aspect ratio 4:3) PC compatibilityResolution:640x480 (Expand) - 1024x768 (Real) - 1280x1024 (Compress) Sync on Green available Video compatibilityNTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM, PAL-60 Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p) Speaker 2W x 1 / 16 ohm S-video inputLuminance signal: 1.0 Vp-p 75 Ω (negative sync.) Chroma signal: 0.286 Vp-p 75 Ω (burst signal) Video input 1.0 Vp-p 75 Ω (negative sync.) Audio input 350 mVrms, 10 kΩ or more Analog RGB inputRGB: 0.7 Vp-p 75 Ω (negative sync.) YP BPR/YCBCR : Y:1.0 Vp-p (negative sync.) PBPR/CBCR:0.7 Vp-p Control connector Serial terminal (RS-232C) (Mini-Din) Outside dimensions 302 x 104.5 x 221 mm (width x height x depth) Weight Approx. 2.6 kg Length of power cord 114 inch (1.8 m) Temperature, humidity (performance guaranteed)+41 °F (+5°C) - +95°F (+35°C), 30 - 90%
EN-26 Specifications (continued) Connectors Dimensional drawings (unit : mm) What’s included in the box Replacement part 15 11 610 15 pin No.Spec. 1 R(RED)/C R 2 G(GREEN)/Y 3B(BLUE)/C B 4NC 5GND 6GND 7GND 8GND 9DDC5V 10- 11- 12 DDC Data 13 HD/CS 14 VD 15 DDC Clock pin No.Spec. 1R(RED) 2G(GREEN) 3B(BLUE) 4- 5GND 6GND 7GND 8GND 9- 10 GND 11 GND 12 - 13 HD/CS 14 VD 15 - COMPUTER IN/MONITOR OUT (D-SUB 15-pin) IN OUT AC power cord 1 RGB cable for PCfor US J2552-0063-01 for EU J2552-0066-01 for UK J2552-0065-01 J2552-0072-032 Remote control with battery (One is installed in the main body) 1 Safety manual/Quick start up 1 CD-ROM 1 Lens cap 1 Soft case 1 Cap RC lock button (Option / Not included in the box) Spare lamp for XD211U VLT-XD210LP 221 104.5 302
EN-27 ENGLISH Specifications (continued) Specification of RGB signals in each computer mode of the projector Important: • Some computers aren’t compatible with the projector. • The projector’s maximum resolution is 1024 x 768 pixels. It may not display images of higher resolutions than 1024 x 768 (or 800 x 600) cor- rectly. • Images with SYNC on G (Green) signal may jitter. • Images with SYNC on G (Green) signal may be tinged with green. • If the resolution and frequency of your computer aren’t shown on the table, find the compatible resolution and frequency by changing the resolu- tion of your computer. • When connecting a HDTV decoder having RGB output terminals, set Signal Type to RGB in the Setting menu. • Video signal with 4 line (R, G, B, CS) and 5 line (R, G, B, H, V) is not supported. • The resolutions of 640 x 480 (72 Hz) and 640 x 480 (75Hz) do not support images with SYNC on G (Green) and Composite Sync. • MONITOR OUT terminal is not available for SYNC on G (Green) signal. Signal mode resolution horizontal frequency (kHz)vertical frequency (Hz)display area (H x V) NTSC (60), 480i (60)- 15.73 59.94 1024 x 768 PAL (50), 576i (50)-15.63 50.001024 x 768 1080i (60) - 33.75 60.00 1024 x 576 1080i 50 - 28.13 50.001024 x 576 480p (60) - 31.47 59.94 1024 x 768 576p (50)- 31.25 50.00 1024 x 768 720p (60) - 45.00 60.00 1024 x 576 720p (50)- 37.50 50.00 1024 x 576 VGA640 x 40024.82 56.42 1024 x 640 37.86 84.13 1024 x 640 37.86 85.08 1024 x 640 640 x 48031.47 59.94 1024 x 768 37.86 72.81 1024 x 768 37.50 75.00 1024 x 768 43.27 85.01 1024 x 768 SVGA 800 x 60035.16 56.25 1024 x 768 37.88 60.32 1024 x 768 48.08 72.19 1024 x 768 46.88 75.00 1024 x 768 53.67 85.06 1024 x 768 XGA 1024 x 76848.36 60.00 1024 x 768 56.48 70.07 1024 x 768 60.02 75.03 1024 x 768 62.94 74.92 1024 x 768 68.68 85.00 1024 x 768 SXGA1152 x 86463.85 70.01 1024 x 768 67.50 75.00 1024 x 768 1152 x 90061.85 66.00 984 x 768 71.81 76.84 984 x 768 1280 x 960 60.00 60.00 1024 x 768 1280 x 1024 63.98 60.02 960 x 768 MAC640 x 480 35.00 66.67 1024 x 768 832 x 624 49.72 74.55 1024 x 768 1024 x 768 60.24 75.02 1016 x 768
EN-28 MITSUBISHI Projector Contact Information 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan MITSUBISHI ELECTRIC CORPORATION North America MESCA (Mitsubishi Electric Sales Canada Inc.) http://www.mitsubishielectric.ca Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2, Canada Sales & Technical Inquires Phone :+1-(800) 450-6487 Fax :+1-(905) 475-7958 E-mail :[email protected] Customer Care E-mail :[email protected] MDEA (Mitsubishi Digital Electronics America, Inc.) (Warranty Registration) http://www.mitsubishi-presentations.com/ Presentation Products Division, 9351 Jeronimo Road, Irvine, CA 92618 U.S.A Sales & Inquires Phone :+1(888) 307-0349 or +1(949)465-6000 E-mail :[email protected] Technical Inquires Phone :+1-(888) 307-0309 E-mail :[email protected] Europe MEU-FRA (Mitsubishi Electric Europe B.V French Branch) 25, Boulevard des Bouvets 92 741, Nanterre CEDEX, France Sales Inquiries Phone :+33 (0)1 55-68-55-53 Fax :+33 (0)1 55-68-57-31 Techinical Inquireis Phone :+33 (0)1 55-68-56-42 Fax :+33 (0)1 55-68-57-31 MEU-GER (Mitsubishi Electric Europe B.V. German Branch) http://www.mitsubishi-evs.de/ Gothaer Strasse 8, 40880 Ratingen, Germany Sales Inquires Phone :0049 - 2102 - 486 9250 Fax :0049 - 2102 - 486 7320 Techinical Inquires Phone :0049 - 2102 - 486 1330 Fax :0049 - 2102 - 486 1340 MEU-IR (Mitsubishi Electric Europe B.V. Irish Branch) http://www.mitsubishi.ie/ Westgate Business Park, Ballymount, Dublin 24, Ireland Sales Inquiries Phone :+353-1-4198807 Fax :+353-1-4198890 Technical Inqiries Phone :+353-1-4198808 Fax :+353-1-4198895 MEU-IT (Mitsubishi Electric Europe B.V. Italian Branch) Centro Direzionale Colleoni, Palazzo Sirio, Viale Colleoni 7, 20041 Agrate Brianza, Italy Sales & Technical Inquiries Phone :+39-(0)39-60531 Fax :+39-(0)39-6053214 E-mail :[email protected] MEU-NL (Mitsubishi Electric Europe B.V. Benelux Branch) http://www.mitsubishi.nl/LCD/ProdFrame.html Nijverheidsweg 23A, 3641 RP Mijdrecht, The Netherlands Sales Inquiries Phone :+31-297-282461 Fax :+31-297-283936 E-mail :[email protected] Techinical Inquiries Phone :+31-297-282461 Fax :+31-297-283936 E-mail :[email protected] Russia (Mitsubishi Electric Europe B.V Moscow Representative Offi ce) http://www.mitsubishi-projector.ru/ Moscow Representative Offi ce, 52/5 Kosmodamianskaya Nab., 115054, Moscow, Russia Sales & Techinical Inquiries Phone :(7095) 721-2068 Fax :(7095) 721-2071 MEU-SP (Mitsubishi Electric Europe B.V. Spanish Branch) http://www.mitsubishielectric.es/ Ctra. de Rubi, 76-80, 08173 Sant Cugat del Valles, Barcelona, Spain Sales Inquiries Phone :+34-93.565.31.54 Fax :+34-93.589.43.88 E-mail :[email protected] Technical Inquiries Phone :+34-93.586.27.51 Fax :+34-93.588.53.87 E-mail :[email protected] MEU-SWE (Mitsubishi Electric Europe B.V Scandinavian Branch) Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden Sales Inquiries Phone :+46-(0)8-6251070 Fax :+46-(0)8-6251036 Technical Inquiries Phone :+46-(0)8-6251052 Fax :+46-(0)8-6251036 MEU-UK (Mitsubishi Electric Europe) http://www.mitsubishi.co.uk/evs/ Visual Information Systems Division, Travellers Lane, Hatfi eld, Hertfordshire, AL10 8XB U.K. Sales Inqiries Phone :+44 (1707) 278684 Fax :+44 (1707) 278541 E-mail :[email protected] Technical Inquiries Phone :+44 (870) 606 5008 Fax :+44 (1506) 431927 E-mail :[email protected] Asia CHINA (Mitsubishi Electric Air-Conditioning & Visual Information Systems (Shanghai) Ltd.) 26/F .,Oriental Center ,699 Nanjing Rd(W),Shanghai, 200041,China Sales Inquiries Phone :+86(21) 5211-0882-3002 Fax :+86(21) 5211-0576 Technical Inquiries Phone :+86(21) 5211-0882-3020 Fax :+86(21) 5211-0576 HONG KONG (Mitsubishi Electric Ryoden Air-Conditioning & Visual Information Systems (HongKong) Ltd.) 7th Floor, Manulife Tower, 169 Electric Road, North Point, Hong Kong Sales Inquiries Phone :+852-2510-1505 Fax :+852-2510-0463 Technical Inquiries Phone :+852-2422-0161 Fax :+852-2487-0181 SINGAPORE (Mitsubishi Electric Asia Pte. Ltd.) http://www.mitsubishielectric.com.sg 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 INDIA (Mitsubishi Electric Asia Pte. Ltd.) 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 INDONESIA (Mitsubishi Electric Asia Pte. Ltd.) 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inqiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 PHILLIPINES (Mitsubishi Electric Asia Pte. Ltd.) http://www.mitsubishielectric.com.sg 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inqiries Phone :+65-6470-2666 Fax :+65-6475-9503 VIETNAM (Mitsubishi Electric Asia Pte. Ltd.) 307, Alexandra Road, #05-01/02 Mitsubishi Electric Building, Singapore 159943 Sales Inquiries Phone :+65-6473-2308 Fax :+65-6475-9503 E-mail :[email protected] Technical Inquiries Phone :+65-6470-2666 Fax :+65-6475-9503 STC (Setsuyo Astec Corporation Seoul Branch) 4F,Dongseo Game Channel Bldg,660-11 Deungchon-Dong, Kangseo-Ku, Seoul, Korea Sales & Technical Inqiries Phone :+82-(0)2-2657-9841~3 Fax :+82-(0)2-2657-9900 MALAYSIA (Antah Melco Sales & Services Sdn. Bhd.) 6, Jalan 13/6 46860 Petaling Jaya Selangor, Darul Ehsan, Malaysia Sales & Technical Inquiries Phone :+60-(0)3-79552088 (Ext. 203) Fax :+60-(0)3-79563950/+60-(0)3-79582576 Technical & Service Inquiries Phone :+60-(0)3-79552088 (Ext. 106) Fax :+60-(0)3-79563950/+60-(0)3-79582576 ME-TWN (Mitsubishi Electric Taiwan Co., Ltd.) http://www.MitsubishiElectric.com.tw 11TH FL., 90 SEC. 6, CHUNG SHAN N. RD., TAIPEI, 111 R.O.C. Sales & Technical Inquires Phone :+886-2-2832-8255 Fax :+886-2-2833-9813 MKY (Mitsubishi Electric Kang Yong Watana Co., Ltd. ) http://www.mitsubishi-kyw.co.th/ Road, Huamark Bangkapi, Bangkok 10240, Thailand Sales & Technical Inquiries Phone :+66-2-731-6841 Fax :+66-2-379-4763 Oceania ME-AUST (Mitsubishi Electric Australia) http://www.mitsubishi-electric.com.au/prod.asp?prod=proj 348 Victoria Road, Rydalmere, N.S.W. 2116, Australia Sales & Technical Inqiries Phone :+(612)9684-7777 Fax :+(612)9684-7208 E-mail :[email protected] Technical Inquiries Phone :+(612)9684-7694 Fax :+(612)9684-7684 E-mail :[email protected] BDT (Black Diamond Technologies Ltd.) (Warranty Registration) http://www.bdt.co.nz/projectors/ warranty.asp 1 Parliament St, Lower Hutt, Wellington, New Zealand Sales Inquiries Phone :+64-(0)4-560-9100 Fax :+64-(0)4-560-9133 E-mail :[email protected] Technical Inquiries Phone :+64-(0)4-560-9100 Fax :+64-(0)4-560-9133 E-mail :[email protected]