Mitsubishi Xd530e Data Projector User Manual
Here you can view all the pages of manual Mitsubishi Xd530e Data Projector User Manual. The Mitsubishi manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 21
EN-21 ENGLISH Projecting images wirelessly This section describes the procedure for projecting images on com- puter screens using the wireless connection (wireless LAN). This data projector supports IEEE802.11b/g. When you use the wireless connection, the MONITOR OUT termi- nal, AUDIO-IN terminal, and AUDIO-OUT terminal cannot be used. When you use the wireless connection and wired LAN connection, audio is not output. A. Connecting the antenna Preparation Make sure that the projector and the computer...
Page 22
EN-22 Projecting images wirelessly (continued) F. Installing the connection softwareInstall the connection software Wireless Projector which is required to project images on computer screens using this projector. Be sure to specify the settings as a user with Administrator rights. 1. Run the Web browser. (Example: Internet Explorer) The administration screen is displayed. If the screen is not displayed, display the Wireless Network Connection properties of your computer, and then check that Obtain...
Page 23
![Page 23
EN-23
ENGLISH
Projecting images wirelessly (continued)
If the wireless connection failsCheck the following points.
Check if the IP address and DNS server address are set to be
obtained automatically in the Internet Protocol (TCP/IP) prop-
erties.
1. Perform the procedure from Step 2 to 5 in E. Connecting wire-
lessly.
2. Right-click Wireless Network Connection to select Proper-
ties.
3. Select Internet Protocol (TCP/IP), then click the [Properties]
button.
4. Select Obtain an IP address automatically...](http://img.usermanuals.tech/thumb/3285/91631/w300_mitsubishi-xd530e-manual_d-22.png "Page 23
EN-23
ENGLISH
Projecting images wirelessly (continued)
If the wireless connection failsCheck the following points.
Check if the IP address and DNS server address are set to be
obtained automatically in the Internet Protocol (TCP/IP) prop-
erties.
1. Perform the procedure from Step 2 to 5 in E. Connecting wire-
lessly.
2. Right-click Wireless Network Connection to select Proper-
ties.
3. Select Internet Protocol (TCP/IP), then click the [Properties]
button.
4. Select Obtain an IP address automatically...")
EN-23 ENGLISH Projecting images wirelessly (continued) If the wireless connection failsCheck the following points. Check if the IP address and DNS server address are set to be obtained automatically in the Internet Protocol (TCP/IP) prop- erties. 1. Perform the procedure from Step 2 to 5 in E. Connecting wire- lessly. 2. Right-click Wireless Network Connection to select Proper- ties. 3. Select Internet Protocol (TCP/IP), then click the [Properties] button. 4. Select Obtain an IP address automatically...
Page 24
EN-24 How to use the connection software For details on the procedure for running the connection software, see page 22. Pausing or resuming the projection Pausing the projection 1. Click the button. Resuming the projection 1. Click the button. Updating the paused projectionYou can update the paused image to the one displayed on the com- puter screen currently. 1. Click the button while pausing images. Projected images are updated each time you click the button. Stopping or starting the projection...
Page 25
![Page 25
EN-25
ENGLISH
How to use the connection software (continued)
4. Select the USB flash drive on which the connection software is
to be installed, and then click the [Next>] button.
Installation of the connection software starts.
5. Click the [Finish] button.
The connection software starts automatically by inserting the USB
flash drive on which the connection software is installed into a
computer.
If the connection software does not start automatically, open the
USB flash drive, and then double-click...](http://img.usermanuals.tech/thumb/3285/91631/w300_mitsubishi-xd530e-manual_d-24.png "Page 25
EN-25
ENGLISH
How to use the connection software (continued)
4. Select the USB flash drive on which the connection software is
to be installed, and then click the [Next>] button.
Installation of the connection software starts.
5. Click the [Finish] button.
The connection software starts automatically by inserting the USB
flash drive on which the connection software is installed into a
computer.
If the connection software does not start automatically, open the
USB flash drive, and then double-click...")
EN-25 ENGLISH How to use the connection software (continued) 4. Select the USB flash drive on which the connection software is to be installed, and then click the [Next>] button. Installation of the connection software starts. 5. Click the [Finish] button. The connection software starts automatically by inserting the USB flash drive on which the connection software is installed into a computer. If the connection software does not start automatically, open the USB flash drive, and then double-click...
Page 26
EN-26 How to use the administration screen Downloading the connection softwareThe procedure for downloading the software is the same as Step 1 to 5 in F. Installing the connection software. See page 22. Selecting the image to be projectedWhen connecting the projector to multiple computers wirelessly, one administrator can select the image to be projected from the computers. Approximately 30 computers can be connected to the projector wirelessly at the same time. However, the number of connectable...
Page 27
![Page 27
EN-27
ENGLISH
How to use the administration screen (continued)
Changing the network settings For the setting items, ask your network administrator.
1. Click Network Setup.
2. Change the settings, then click the [Apply] button. You can change the following settings.
When using multiple units of the wireless projector, do not
overlap the settings for SSID in Wireless Setup.
3. Check the displayed settings, then click the [OK] button.
4. Reboot the system.
The specified settings can be applied.
It takes...](http://img.usermanuals.tech/thumb/3285/91631/w300_mitsubishi-xd530e-manual_d-26.png "Page 27
EN-27
ENGLISH
How to use the administration screen (continued)
Changing the network settings For the setting items, ask your network administrator.
1. Click Network Setup.
2. Change the settings, then click the [Apply] button. You can change the following settings.
When using multiple units of the wireless projector, do not
overlap the settings for SSID in Wireless Setup.
3. Check the displayed settings, then click the [OK] button.
4. Reboot the system.
The specified settings can be applied.
It takes...")
EN-27 ENGLISH How to use the administration screen (continued) Changing the network settings For the setting items, ask your network administrator. 1. Click Network Setup. 2. Change the settings, then click the [Apply] button. You can change the following settings. When using multiple units of the wireless projector, do not overlap the settings for SSID in Wireless Setup. 3. Check the displayed settings, then click the [OK] button. 4. Reboot the system. The specified settings can be applied. It takes...
Page 28
![Page 28
EN-28
How to use the administration screen (continued)
Glossary
Changing the settings for the projectionYou can change the settings for the number of colors and the login
code.
1. Click Projection Setup.
2. Change the settings, then click the [Apply] button. You can change the following settings.
3. Check the displayed settings, then click the [OK] button.
4. Reboot the system.
The specified settings can be applied.
It takes approximately one minute to reboot the system.
Changing the passwordYou can...](http://img.usermanuals.tech/thumb/3285/91631/w300_mitsubishi-xd530e-manual_d-27.png "Page 28
EN-28
How to use the administration screen (continued)
Glossary
Changing the settings for the projectionYou can change the settings for the number of colors and the login
code.
1. Click Projection Setup.
2. Change the settings, then click the [Apply] button. You can change the following settings.
3. Check the displayed settings, then click the [OK] button.
4. Reboot the system.
The specified settings can be applied.
It takes approximately one minute to reboot the system.
Changing the passwordYou can...")
EN-28 How to use the administration screen (continued) Glossary Changing the settings for the projectionYou can change the settings for the number of colors and the login code. 1. Click Projection Setup. 2. Change the settings, then click the [Apply] button. You can change the following settings. 3. Check the displayed settings, then click the [OK] button. 4. Reboot the system. The specified settings can be applied. It takes approximately one minute to reboot the system. Changing the passwordYou can...
Page 29
![Page 29
EN-29
ENGLISH
Uninstalling the connection software
This section describes the procedure for uninstalling the connection
software.
1. Click the Start button, then select [All Programs] → [Wireless
Projector] → [Uninstall].
2. Click the [Yes] button.
The uninstallation of the connection software Wireless Pro-
jector starts.
3. Click the [OK] button.](http://img.usermanuals.tech/thumb/3285/91631/w300_mitsubishi-xd530e-manual_d-28.png "Page 29
EN-29
ENGLISH
Uninstalling the connection software
This section describes the procedure for uninstalling the connection
software.
1. Click the Start button, then select [All Programs] → [Wireless
Projector] → [Uninstall].
2. Click the [Yes] button.
The uninstallation of the connection software Wireless Pro-
jector starts.
3. Click the [OK] button.")
EN-29 ENGLISH Uninstalling the connection software This section describes the procedure for uninstalling the connection software. 1. Click the Start button, then select [All Programs] → [Wireless Projector] → [Uninstall]. 2. Click the [Yes] button. The uninstallation of the connection software Wireless Pro- jector starts. 3. Click the [OK] button.
Page 30
EN-30 How to use wired LAN connection The function described in the previous section for the wireless connection can be applied also to the wired LAN connection similarly. When the wireless connection is poor and the network settings cannot be configured, use the function. For Ethernet connection 1. Connect one end of the Ethernet cable to the LAN terminal of the projector. Use a cross cable. Use a Category 5 cable. 2. Connect the other end of the Ethernet cable to the Ethernet port of the computer....