Motorola Dp3400 3401 3600 3601 Mototrbo Basic 6866574d29 E Manual

Transceiver Performance Testing Display Model Test Mode 3-3
3.3 Display Model Test Mode
3.3.1 Entering Display Radio Test Mode
1. Turn the radio on.
2. Within 10 seconds after Self Test is complete, press  Side Button 2 five times in succession
3. The radio beeps and will show a series of disp lays that will give information regarding various 
version numbers and subscriber specific inform ation. The displays are described in Table 3-2.
NOTE: The radio  stops at each display for 2 seconds before  moving...

3-4Transceiver Performance Testing Display Model Test Mode
2. Each short press of Side Button 1 toggles the channel spacing between 25 kHz, 12.5 kHz 
and 20 kHz as. The radio beeps once when radi o toggles to 20kHz, beeps twice for 25 kHz 
and beeps three times for 12.5 kHz.
3. Turning of the  Channel Knob changes the test channel from 1 to 14 as described in 
Table 3-4. The radio beeps in each position. Table 3-3.  Test Environments
No. of 
Beeps Description Function
1Carrier Squelch
(CSQ)RX: if carrier...

Transceiver Performance Testing Display Model Test Mode 3-5
Table 3-5.  Transmitter Performance Checks
Te s t  N a m eCommunications 
Analyzer Radio Test Set Comments
Reference 
FrequencyMode: PWR MON
4th channel test 
frequency*
Monitor: Frequency 
error
Input at RF In/OutTEST MODE,
Test Channel 4 
carrier squelchPTT to 
continuously
transmit
(during the 
performance 
check)Frequency error to be 
±654 Hz for 
non-GPS models 
(UHF1)
±218 Hz for GPS 
models (UHF1)
±729 Hz for 
non-GPS models 
(UHF2)
±243...

3-6Transceiver Performance Testing Display Model Test Mode
* See Table 3-4 
* See Table 3-4Table 3-6.  Receiver Performance Checks
Te s t  N a m e
Communications 
Analyzer Radio Test Set Comments
Reference 
FrequencyMode: PWR MON
4th channel test
frequency*
Monitor: Frequency error
Input at RF In/OutTEST MODE,
Test Channel 4 
carrier squelch 
output at 
antennaPTT to 
continuously 
transmit
(during the 
performance 
check)Frequency error to be 
±654 Hz for 
non-GPS models 
(UHF1)
±218 Hz for GPS 
models...

Transceiver Performance Testing Display Model Test Mode 3-7
3.3.3 Display Test Mode
1. Press and hold Side Button 1 in RF Test Mode. The radio beeps once and momentarily 
displays “Display Test Mode”. 
2. Upon entering Display Test Mode, the radio di splays a horizontal line on row 8 (center row).
3. With each button/key press, the radio fills the screen up with 2  horizontal lines from the center 
row (1 line each above and below the center row)  until the top and bottom of the screen (row 
7-0 and row...

3-8Transceiver Performance Testing Display Model Test Mode
3.3.9 Battery Check Test Mode
1. Press and hold Side Button 1 after Audio Loopback Earpiece Test Mode. The radio beeps 
once and momentarily displays “Battery Check Test Mode”. 
2. The radio will display the following:
Figure 3-1.  Battery Check Test Mode Display
3.3.10 Button/Knob/PTT Test Mode
1. Press and hold  Side Button 1 after Battery Check Test Mode. The radio beeps once and 
displays “Button Test”(line 1). 
2. The radio also displays the...

Transceiver Performance Testing Display Model Test Mode 3-9
- Press OK, “85/1” appears & radio beeps; release, “85/0” appears & radio beeps.
- Press MENU , “139/1” appears & radio beeps; rel ease, “139/0” appears & radio beeps.
- Press BACK , “129/1” appears & radio beeps; release, “129/0” appears & radio beeps.
- Press 
W, “128/1” appears & radio beeps; release, “128/0” appears & radio beeps.
- Press 
X, “130/1” appears & radio beeps; release, “130/0” appears & radio beeps. 

3-10Transceiver Performance Testing Non–Display Model Test Mode
3.4 Non–Display Model Test Mode
3.4.1 Entering Non–Display Radio Test Mode
1. Turn the radio on.
2. Within 10 seconds after “Self Test” is complete, press  Side Button 2 five times in succession.
3. The radio beeps.
3.4.2 RF Test Mode
When the radio is operating in its normal environm ent, the radios microcontroller controls the RF 
channel selection, transmitter key-up, and receiv er muting, according to the customer codeplug...

Transceiver Performance Testing Non–Display Model Test Mode 3-11
3.4.5 Earpiece Tone Test Mode
1. Press and hold Side Button 1 after Speaker Tone Test Mode. The radio beeps once.
2. The radio generates a 1 KHz tone with the earpiece.
3.4.6 Audio Loopback  Earpiece Test Mode
1. Press and hold Side Button 1 after Earpiece Tone Test Mode. The radio beeps once.
2. The radio shall route any audio on the external mic to the earpiece. 
3.4.7 Battery Check Test Mode
1. Press and hold  Side Button 1 after Audio...

Notes
3-12Transceiver Performance Testing Non–Display Model Test Mode