MSI C 770-c45 Manual


MS-7599

ConnectorsBack panel PS/2 mouse port 
 PS/2 keyboard port
 Serial port
6 uSB 2.0 Ports
 Lan jack
6 flexible audio jacks
on-Board  uSB 2.0 connectors 
 SPdiF-out connector
 Front Panel audio connector
 Chassis intrusion connector
 Cd-in connector
 tPM connector
Slots  PCi express x6 slot, supports PCie Gen2.0
2 PCi express x slots, supports PCie Gen2.0
 PCi slots, support .V/ 5V PCi bus interface
Form...

2

ReaR PaneL
the rear panel provides the following connectors:
HaRdWaRe SetuP
this  chapter  tells  you  how  to  install  the  CPu,  memory  modules,  and  expansion 
cards, as well as how to setup the jumpers on the mainboard. it also provides the 
instructions on connecting the peripheral devices, such as the mouse, keyboard, etc. While doing the installation, be careful in holding the components and follow the installation procedures.
CPu & Cooler installation for aM
When you are...


MS-7599

Pull  the  lever  sideways  away  from  the  socket.  Make  sure  to  raise  the  lever  up  to  a  90-degree angle.
Look  for  the  gold  arrow  of  the  CPu. the  gold 
arrow  should  point  as  shown  in  the  picture.  the 
CPu can only fit in the correct orientation.
if the CPu is correctly installed, the pins should be 
completely embedded into the socket and can not be seen. Please note that any violation of the cor-rect installation procedures may cause permanent damages to...

4

installing Memory Modulesthe memory module has only one notch on the center and will only fit in the 
right orientation.
insert  the  memory  module  vertically  into  the  diMM  slot. then  push  it  in  until 
the golden finger on the memory module is deeply inserted in the  diMM slot. 
the plastic clip at each side of the  diMM slot will automatically close when the 
memory module is properly seated. you can barely see the golden finger if the memory module is properly inserted in the diMM...

5
MS-7599

atX 24-Pin Power Connector: atX
this connector allows you to connect an atX 24-pin power supply. to connect the 
atX  24-pin  power  supply,  make  sure  the  plug  of  the  power  supply  is  inserted  in 
the proper orientation and the pins are aligned.  then push down the power supply 
firmly into the connector.
1 3 . + 3 . 3V
1 . + 3 . 3V
1 4 . - 1 2 V
2 . + 3 . 3V
1 5 . G r o u n d
3. G r o u n d
1 6 . P S - O N
#
4 . + 5V
1 7 . G r o u n d
5. G r o u n d
1 8 . G r o u n d
6 ....

6

ide Connector: ide
this  connector  supports ide  hard  disk  drives,  optical  disk  drives  and  other  ide 
devices.
iMPoRtant
if  you  install  two  ide  devices  on  the  same  cable,  you  must  configure  the  drives 
to  cable  select  mode  or  separately  to  master  /  slave  mode  by  setting  jumpers. 
Refer  to  ide  device  documentation  supplied  by  the  vendors  for  jumper  setting 
instructions.
Serial ata Connector: Sata ~ 6
this  connector  is  a  high-speed...

7
MS-7599

S/PdiF-out Connector: JSPd
this  connector  is  used  to  connect  S/PdiF  (Sony  &  Philips digital interconnect 
Format) interface for digital audio transmission.
1.VCC2.SPDIF3.Ground
Cd-in Connector: Cd_in
this connector is provided for external audio input.
4.R3.Ground
2.Ground
1.L
Front Panel Connectors: JFP, JFP2
these  connectors  are  for  electrical  connection  to  the  front  panel  switches  and 
Leds. the  JFP  is  compliant  with  intel
®  Front  Panel...

8

Front uSB Connector: JuSB/ JuSB2/ JuSB
this  connector,  compliant  with intel® i/o  Connectivity  design  Guide,  is  ideal  for 
connecting high-speed  uSB interface peripherals such as uSB Hdd, digital cam-
eras, MP players, printers, modems and the like.
1 . V CC3 . U S B D-
1 0 . U S B OC
5 . U S B D+
7. G r o u n d9 . N oP in
8. G r o u n d6 . U S B D+4 . U S B D-2 . V CC
tPM Module connector: JtPM
this connector connects to a  tPM (trusted Platform Module) module....

9
MS-7599

Clear CMoS Jumper: JBat
there is a CMoS RaM onboard that has a power supply from an external battery 
to  keep  the  data  of  system  configuration.  With  the  CMoS  RaM,  the  system  can 
automatically  boot oS  every  time  it  is  turned  on.  if  you  want  to  clear  the  system 
configuration, set the jumper to clear data.
JBatkeep data
Clear data
111
iMPoRtant
you  can  clear  CMoS  by  shorting  2-  pin  while  the  system  is  off.  then  return  to 
-2...

20

PCi express Slot
the PCi express slot supports the PCi express interface expansion card.the PCi express 2.0 x6 slot sup
-ports up to 8.0 GB/s transfer rate.
the PCi express 2.0 x slot sup
-ports up to 500 MB/s transfer rate.
PCi Slot
the  PCi  slot  supports  Lan  card,  SCSi  card,  uSB  card,  and  other  add-on  cards 
that comply with PCi specifications.
iMPoRtant
Make sure that you unplug the power supply first. Meanwhile, read the documen-tation for the expansion card to configure...