Multitech Multivoip 100 Model Mvp110 Standalone Voice/ip Gateway Quick Start Guide



	


Standalone Voice/IP Gateway
Model MVP110
Proprietary Mode
Quick Start Guide 

Quick Start Guide
82050750 Revision A
MultiVOIP 100 (Model MVP110)
This publication may not be reproduced, in whole or in part,
without prior expressed written permission from Multi-Tech
Systems, Inc.  All rights reserved.
Copyright © 2001, by Multi-Tech Systems, Inc.
Multi-Tech Systems, Inc. makes no representations or warranties
with respect to the contents hereof and specifically disclaims any
implied warranties of merchantability or fitness for any particular
purpose.  Furthermore, Multi-Tech...

iii
Contents
Introduction ................................................................................... 4
Related Documentation ................................................................. 5
Installing Your MultiVOIP ............................................................... 6
Unpacking Your MultiVOIP ............................................................ 8
Safety Warnings ............................................................................ 8
Cabling Your MultiVOIP...

MultiVOIP Quick Start Guide
4
Introduction
Welcome to Multi-Techs stand-alone Voice/IP Gateway, the
MultiVOIP model MVP110.  The MultiVOIP enables FXS-only
analog voice and fax communication over an IP network. Multi-
Tech’s new voice/fax gateway technology allows voice and fax
communication to ride, with no additional expense, over your
existing IP network, which has traditionally been data-only.  To
access this free voice and fax communication, all you have to do
is connect the MultiVOIP to your...

5 Introduction
Related Documentation
The MVP110 Quick Start Guide is intended to be used by
qualified systems administrators and network managers.  This
quick start provides the necessary information for a qualified
person to unpack, cable, load software, and configure the unit
for proper operation.
A detailed MVP110 User Guide is also provided on the system
CD with your unit and provides in-depth information on the
features and functionality of Multi-Tech’s MultiVOIP.
The User Guide is produced using...

MultiVOIP Quick Start Guide
6
Installing Your MultiVOIP
The basic steps of installing your MultiVOIP network involve
unpacking the units, connecting the cables, and configuring
the units using the included management software (MultiVOIP
Configuration).  The recommended installation process
includes three phases that, when completed, result in a fully
functional Voice Over IP network.  A general description of
each phase is provided below, and detailed instructions follow
throughout the rest of this...

7 Introduction
Deploy the VOIP Network
The final phase of the installation is deployment of the
network.  Through the first two phases, the VOIP administrator
controls configuration, so when the Client MultiVOIPs are sent
to their remote sites, the remote site administrators need only
to connect the units to their LAN and telephone equipment.  A
full Phone Directory Database (supplied by the Host
MultiVOIP) will be loaded into their unit within minutes of being
connected and turned on.
The final task of...

MultiVOIP Quick Start Guide
8
Unpacking Your MultiVOIP
Remove all items from the box (See Figure 4).



	


	




Figure 4.  Unpacking
Safety Warnings
Caution: Danger of explosion if battery is incorrectly replaced.
A lithium battery on the voice/fax channel board provides
backup power for the time keeping capability.  The battery has
an estimated life expectancy of ten years.
When the battery starts to weaken, the date and time may be
incorrect....

9 Cabling
Cabling Your MultiVOIP
Cabling your MultiVOIP involves making the proper Power,
Command Port, phone system, and Internet connections.
Figure 5 shows the back panel connectors and the associated
cable connections.  The following procedure details the steps
necessary for cabling your MultiVOIP.
1. Connect the power supply to a live AC outlet, then connect
it to the MultiVOIP as shown in Figure 5.









Figure 5.  Cable Connections
2....

MultiVOIP Quick Start Guide
10Voice/Fax Channel connector on the back of the
MultiVOIP and the other end to the station device.
5. Turn on power to the MultiVOIP by setting the power
switch on the right side panel to the On position.  Wait for
the Boot LED on the MultiVOIP to go off before
proceeding.  This may take a couple of minutes.
Proceed to the Software Loading section to load the MultiVOIP
software.