Multitech Multivoip 100 Model Mvp110 Voice/fax Over Ip Networks User Guide

31 Chapter 3 - Software Loading and Configuration
30. The Description box is optional, but can be useful in associating the channel to the extension. If
you wish, enter a description of your local phone number. This description serves to identify the
phone number you entered in the previous step.  Normally the “Master” MVP110 resides at the
entity’s main office; therefore, for this example you could enter a description such as “New York
Office”).
31. The Station Identification group includes a Hunt Group...

32 Chapter 3 - Software Loading and Configuration
34. Enter the phone number for the MultiVOIP in the Station Information group Phone Number
box.
35. Click inside the Description box and enter a description for the remote MVP110 phone number
for the Voice/Fax Channel.
36. In the Station Identification group, select HUNT GROUP #2 from the Hunt Group list, enter the
London Office’s IP Address (202.056.039.100), and accept the H.323 industry standard Port
value (1720) used to communicate with other H.323...

33 Chapter 3 - Software Loading and Configuration
42. Click OK and you are returned to the Phone Directory Database dialog box which now includes
the stand-alone phone number and related information in the Phone Number list.
43. When you have finished, click OK to download the setup configuration to the MVP110.
44. Click OK.  After the setup is written to the MVP110, the unit reboots.
45. Verify that the BOOT LED on the MVP110 is off after the download is complete. This may take
several minutes as the...

34 Chapter 3 - Software Loading and Configuration
Configuring Your Slave MVP110s
If the Proprietary Phonebook option on the Phone Directory Database dialog box was enabled,
then you will need to configure all remote H.323 endpoints as “Slave” units. For example, the
MVP110 at the company’s subsidiary office in London would need to be configured as a “Slave.”
CAUTION: If you are installing a MVP110 behind a Firewall, the Firewall must support H.323. Refer
to your Firewall user documentation to enable...

35 Chapter 3 - Software Loading and Configuration
The IP Address is the unique IP address that you assign to the MVP110, and the Gateway
Address is the IP address of the device (such as a network router) connected to the Internet/
Intranet.
Click OK when you are finished. The Main menu displays.
5. From the Main menu, click Voice Channels to display the Channel Setup dialog box. The
Channel Setup dialog box displays. The four tabs in this dialog box define the channel interface,
voice/fax parameters,...

36 Chapter 3 - Software Loading and Configuration
valid range  is +31dB to –31dB with a recommended/default value of 0.
You can also set up the DTMF gain (or output level in decibels - dB) for the higher and lower
frequency groups of the DTMF tone pair.  Make your selections in the lists in the DTMF Gain
group.
Note: Only change the DTMF gain under the direction of Multi-Tech Technical Support.
9. To change the voice coder, select the Manual in the Coder group. Select the appropriate coder
from the...

37 Chapter 3 - Software Loading and Configuration
12. If you want to dedicate a local voice/fax channel to a remote voice/fax channel (so you will not
have to dial the remote channel), click the Auto Call Enable option in the Auto Call group. Then
enter the phone number of the remote MVP110 in the Phone Number box.
13. The Automatic Disconnection group provides three options to be used singly or in combination.
The Jitter Value defines the average inter-arrival packet deviation (in milliseconds) before...

38 Chapter 3 - Software Loading and Configuration
Make certain the Proprietary Phonebook option is enabled and in the Database Type group,
click the Slave option. The Master IP Address field becomes active.
Note: After you have enabled the Slave option, the Slave Status button is replaced by the
Update button. Once your Phone Directory database has been established, you can click this
button to refresh the entries in the Phone Directory Database window.
18. Enter the IP address (204.022.122.118) of the...

39 Chapter 3 - Software Loading and Configuration
Deploying the VOIP Network
For a Proprietary Phone Directory database, the VOIP administrator can deploy the pre-configured slave
MVP110s to their remote sites. The remote site administrators need only connect power to the pre-configured
MVP110, connect the MVP110 to their Ethernet LAN and predefined telephone equipment, and then wait for the
phone directory database to be downloaded.
With the Gatekeeper option enabled on the Phone Directory Database...



	


Chapter 4 - MVP110 Software