Multitech Multivoip 100 Model Mvp120 Voice/fax Over Ip Networks User Guide

41 Chapter 5 - Configuring the Slave MultiVOIPs
Multi-Tech Systems, Inc. MultiVOIP User GuideCall Duration defines the maximum length of time (in seconds) that a call remains
connected before the call is automatically disconnected. The default setting is 180 seconds.
A call limit of three minutes may be too short for most configurations. Therefore, you may
want to increase this default value.
14. You can set billing options for inbound and/or outbound calls by selecting them in the Billing
Options group...

42 Chapter 5 - Configuring the Slave MultiVOIPs
Multi-Tech Systems, Inc. MultiVOIP User Guide
Note: After you have enabled the Slave option, the Slave Status button is replaced by the
Update button. Once your Phone Directory database has been established, you can click
this button to refresh the entries in the Phone Directory Database window.
18. Enter the IP address (204.022.122.118) of the New York Office MVP120 in the Master IP
Address box and enable the Send Status Report to Master so that status...



	


Chapter 6
Deploying the VOIP Network 

44 Chapter 6 - Deploying the VOIP Network
Multi-Tech Systems, Inc. MultiVOIP User Guide
Chapter 6 - Deploying the VOIP Network
For a Proprietary Phone Directory database, the VOIP administrator can deploy the pre-
configured slave MVP120s to their remote sites. The remote site administrators need only
connect power to the pre-configured MVP120, connect the MVP120 to the Ethernet LAN and
predefined telephone equipment, and then wait for the phone directory database to be
downloaded.
With the Gatekeeper...



	


Chapter 7
 Using the MultiVOIP Software 

46 Chapter 7 - Using the MultiVOIP Software
Multi-Tech Systems, Inc. MultiVOIP User Guide
Chapter 7 - Using the MultiVOIP Software
This chapter describes various features of the MVP120 software that enable you to change
the configuration of your MVP120. The default configuration parameters were entered during
the loading of the software. The MVP120 software and configuration utilities described in this
chapter enable you to change that initial configuration as necessary.
The primary interface to the...

47 Chapter 7 - Using the MultiVOIP Software
Multi-Tech Systems, Inc. MultiVOIP User Guide
MVP120 Configuration
The MVP120 Setup menu consists of 10 buttons, an Events window in the middle of the
menu, and a status bar at the bottom of the menu. The 10 buttons allow you to display and
change the voice channels and IP protocol parameters, display and manage the Phone Book
listing, view statistics and call progress, and change features such as SNMP Agent, Telnet
Server, WEB Server, and assign a MVP120...

48 Chapter 7 - Using the MultiVOIP Software
Multi-Tech Systems, Inc. MultiVOIP User Guide
Changing Channel Parameters
The channel parameters include the interface type and its options, voice and fax settings,
billing and security, and voice communications for the country and region in which the
MVP120 is operating. The Channel Setup dialog box, accessed by clicking Voice Channels
on the Setup menu, has four tabs that display the following categories of channel information
-- Interface, Voice/Fax,...

49 Chapter 7 - Using the MultiVOIP Software
Multi-Tech Systems, Inc. MultiVOIP User GuideFor FXO-to-FXO communications, you can enable a specific kind of FXO Disconnect Options:
Current Loss, Tone Detection, or Silence Detection.  Check with your in-house phone
personnel to verify the type of disconnect to use. If current lossis checked, the VOIP will hang up
when it detects a loss of current on the FXO (phone) port. For tone detection, select from the
lists one or two tones that will cause the line to...

50 Chapter 7 - Using the MultiVOIP Software
Multi-Tech Systems, Inc. MultiVOIP User GuideThe Fax group enables a fax machine to transmit and receive faxes through the MVP120. If a
fax machine is connected to the via PBX port or PTSN, the Max Baud Rate should be set to
match the baud rate of the fax machine (refer to user documentation). The Fax Volume setting
controls the output level of the fax tones, and this setting should be changed only under the
direction of Multi-Tech’s Technical Support...