Namco Ace Driver Deluxe Installation Commissioning Manual

Part No. 90500031
ACE DRIVER
DELUXE
Installation and Commissioning
Manual
IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN
CUSTOMER
 SAFETY AT ALL TIMES, AND IT IS IMPERATIVE THAT
THE
 DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY. 

© 1994Ltd - all rights reserved.
Published by:
BRENT LEISURE Ltd.
Unit 1 Brent Crescent,
London. NW10 0QT
Phone:- 0181-965-0550
Fax:- 0181-961-0574 No part of this publication may be reproduced by any mechanical, photographic or electronic
process, or in the form of phonographic recording, nor may it be stored in a retrieval system,
transmitted or otherwise copied for public or private use, without permission from 
 Ltd.
While the information contained in this manual is given in good faith and was...

This machine is designed for indoor use only. Do not install the machine in the following places. 

SAFETY WARNING
In Order to Use This Machine Safely
In order to use this machine safely, be sure to read this  Installation and
Commissioning manual and the Operators Manual carefully before installation and use
of the machine.
Whenever the owner of this machine entrusts disassembly, installation, adjustment,
routine maintenance or trouble shooting to another person, the owner should ensure
that they read the appropriate precautions and relevant sections of this manual before
starting work.
In order that...

Contents
1. INSTALLATION........................................................................................... 7
1-1 Installing the Sign Assembly .................................................................................. 8
1-2 Installing the Sign Boards (L), (R) ......................................................................... 9
1-3 Connecting the Seat Assemblies to the Tower Assembly ................................... 10
1-4 Removing the Shipping Brackets...

1. INSTALLATION
Notes on installation
DANGER: NEVER turn the power to the machine ON until installation has been
completed.
DANGER: In order to avoid injury or damage to the machine due to mis-operation,
ensure that the voltage of the mains in supply is 220-240volt AC. Also,
in order to prevent possible electric shocks, be sure that the machine is
connected to the mains in supply with a securely connected earthed
plug.
NOTE: When installing the machine, in order to maintain customer safety, be
sure to...

Page
1-1 Installing the Sign Assembly
For your convenience, the sign assembly has already been fitted to the tower unit.
NOTE: The weight of the Sign Assembly (not including the sign board) is 32kg. The
centre of gravity of the Sign Assembly is to the front , making it unstable, and
as assembly involves lifting the Sign Assembly above head height, at least
two people should be used to install the Sign Assembly.
1) Remove the two security screws (M5x12), and remove the harness cover.
2) Make sure that...

Page 1-2 Installing the Sign Boards (L), (R)
The overall height of the machine can be adjusted by altering the position at which the
sign boards are fitted.
Normal Height (Total height: 2,200mm)
1) Bring the Sign Boards (L), (R) close to the fixing position, and connect the
connectors.
2) Hang the Sign Boards (L) (R) on the side joints (L) (R).
3) Slide the Sign Boards (L) (R) to the back, and fasten to the cabinet using two
security screws (M6x20).
Lower Height (Total height: 2,140mm)
1) Remove the two...

Page 1-3 Connecting the Seat Assemblies to the Tower Assembly
1) Insert the seat assembly from the side of the tower unit so that the front legs of
the tower unit are underneath the seat assembly.
2) Remove the four security screws (M5x12) from the bottom front of the tower unit,
and remove the lower front cover (F). Temporarily fasten the seat unit with two
hex head bolts (M10x25), flat washers and safety washers. (Do not tighten)
3) Remove the four security screws (M5x12) from the bottom rear of the...

Page 8) Insert the front rubber brackets (L), (R) of the tower unit in the side panel of the
seat assembly, and fasten them with two security screws (M5x16) and two
No6X½ pozi flange head screws.
9) Remove the five security screws (M5x16) from the tower side support.
10) Fit the rear safety rubbers to the tower unit with the retaining bracket and the five
security screws (M5x16) previously removed from the tower side support.
11) Place the left, centre, and right safety warning mats in their correct...