Namco Ace Driver Deluxe Installation Commissioning Manual

							Part No. 90500031
ACE DRIVER
DELUXE
Installation and Commissioning
Manual
IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN
CUSTOMER
 SAFETY AT ALL TIMES, AND IT IS IMPERATIVE THAT
THE
 DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY. 
						

							© 1994Ltd - all rights reserved.
Published by:
BRENT LEISURE Ltd.
Unit 1 Brent Crescent,
London. NW10 0QT
Phone:- 0181-965-0550
Fax:- 0181-961-0574 No part of this publication may be reproduced by any mechanical, photographic or electronic
process, or in the form of phonographic recording, nor may it be stored in a retrieval system,
transmitted or otherwise copied for public or private use, without permission from 
 Ltd.
While the information contained in this manual is given in good faith and was accurate at the
time of publication, BRENT LEISURE LIMITED reserve the right to make changes and
alterations without notice.
This machine has been manufactured in accordance with European Community directives (1st.
January 1995), and as such bears the 
 marking. Any changes or modifications to this
machine must be in accordance with European Community directives (1st. January 1995).
If you make any unauthorised changes to this product, you may contravene European
Community directives (1st. January 1995) 
						

							This machine is designed for indoor use only. Do not install the machine in the following places. 
						

							SAFETY WARNING
In Order to Use This Machine Safely
In order to use this machine safely, be sure to read this  Installation and
Commissioning manual and the Operators Manual carefully before installation and use
of the machine.
Whenever the owner of this machine entrusts disassembly, installation, adjustment,
routine maintenance or trouble shooting to another person, the owner should ensure
that they read the appropriate precautions and relevant sections of this manual before
starting work.
In order that no accidents occur when the machine is in operation, 
strictly
follow the notes on safety described below.
Do not turn the machine ON until it has been correctly installed.
Warnings for Operation
NOTE:Only operate this machine after checking that it has been installed correctly
in accordance with this Installation and Commissioning manual.
NOTE:Parts of this machine move during game play, so there are places where the
distance between the stationary section and moveable section changes.
There are warning stickers to keep hands and feet clear of moving parts,
however if the operator feels that a customer playing the game is in any
danger, he should warn the customer accordingly.
NOTE:The warning stickers must always be kept in good condition and replaced if
worn so that the customer can read them clearly.
NOTE:If there is an error or problem with this machine, operation must be
stopped immediately.
Warnings for Disassembly, Installation, Routine Maintenance and Troubleshooting
DANGER:Namco Ltd. bears absolutely no responsibility for accidents or injuries
resulting from unauthorized changes to the machine.
DANGER:Ensure that the machine has been turned OFF before making adjustments
or carrying out maintenance. Also ensure only qualified personnel carry out
maintenance or turn the power ON  to this machine.
DANGER:The power supply and inside the monitor will remain hot and have areas of
high voltage even though the machine has been turned OFF, and there is a
possibility of burns or electric shock. Be careful not to touch these areas.
DANGER:In order to avoid injuries due to mis-operation, be sure that the voltage of the
power supply is within the prescribed limits. Also to prevent possible electric
shocks due to failure, this machine MUST be fitted with a securely
connected earthed plug.
NOTE:Do not turn the main power switch ON until the machine has been installed
correctly. 
						

							Contents
1. INSTALLATION........................................................................................... 7
1-1 Installing the Sign Assembly .................................................................................. 8
1-2 Installing the Sign Boards (L), (R) ......................................................................... 9
1-3 Connecting the Seat Assemblies to the Tower Assembly ................................... 10
1-4 Removing the Shipping Brackets ........................................................................ 12
1-5 Installing the Guard Fence ................................................................................... 14
1-6 Applying the Number Stickers .............................................................................. 15
1-7 Linking Two or More Machines. ........................................................................... 16
1-7-1 Setting the Link Switches ...................................................................... 17
2 ADJUSTMENTS....................................................................................... 18
2-1 Turning on the Power .......................................................................................... 18
2-2 Adjustment Switches ........................................................................................... 18
2-3 Test Mode ............................................................................................................ 19
2-3-1 Coin Options .......................................................................................... 20
2-3-2 Game  Options ...................................................................................... 21
2-3-3 I/O Test .................................................................................................. 23
2-3-4 Switch Test ............................................................................................ 24
2-3-5 Motor Test .............................................................................................. 25
2-3-6 Motion Stop Test .................................................................................... 25
2-3-7 Lamp Test .............................................................................................. 26
2-3-8 LED Test ................................................................................................ 26
2-3-9 Sound Test ............................................................................................ 27
2-4 Adjustments When Replacing Parts (Initialization) ............................................. 28
3. DISASSEMBLY......................................................................................... 29
3-1. Removing the Monitor Assy (L), (R) ..................................................................... 30
3-2 Disassembling the Upper Seat Assy from the Seat Base Assy .......................... 31 
						

							1. INSTALLATION
Notes on installation
DANGER: NEVER turn the power to the machine ON until installation has been
completed.
DANGER: In order to avoid injury or damage to the machine due to mis-operation,
ensure that the voltage of the mains in supply is 220-240volt AC. Also,
in order to prevent possible electric shocks, be sure that the machine is
connected to the mains in supply with a securely connected earthed
plug.
NOTE: When installing the machine, in order to maintain customer safety, be
sure to attach the supplied rear fence and safety warning mats.
NOTE: In order to prevent customer injury when the machine is being played,
make sure that the space between the side of the machine and a wall
or other machine is at least 30cm.
NOTE: In order that the PCB rack or power supply can be removed for service,
make sure that the rear of the machine is separated from a wall or other
machine by a distance of at least 50cm.
[NOTE]
The shipping brackets that are removed during installation will be required
to be refitted for moving, shipping, and for maintenance when the drive
castor is worn. They should be stored safely and not lost or thrown away.
Page 1 
						

							Page
1-1 Installing the Sign Assembly
For your convenience, the sign assembly has already been fitted to the tower unit.
NOTE: The weight of the Sign Assembly (not including the sign board) is 32kg. The
centre of gravity of the Sign Assembly is to the front , making it unstable, and
as assembly involves lifting the Sign Assembly above head height, at least
two people should be used to install the Sign Assembly.
1) Remove the two security screws (M5x12), and remove the harness cover.
2) Make sure that there are no wires or connectors on top of the main tower assy. If
there is, drop them in to the tower.
3) NOTE: The Sign Assembly is unstable. Ensure that one person maintains the
balance of the sign assembly during installation.
4) Place the Sign Assembly on top of the tower, making sure that the Sign
Assembly is forward of the tab at the top rear of the tower. Centre the Sign
Assembly left to right and push the assembly back until the base board engages
in to the tab.
5) Using the four hex head bolts (M10x30) and washers supplied, secure the Sign
Assembly to the main tower assembly.
6) Feed the harness through from the tower assembly and connect the connectors.
Refit the harness cover using the two security screws (M5x12) removed in step 1.
2 
						

							Page 1-2 Installing the Sign Boards (L), (R)
The overall height of the machine can be adjusted by altering the position at which the
sign boards are fitted.
Normal Height (Total height: 2,200mm)
1) Bring the Sign Boards (L), (R) close to the fixing position, and connect the
connectors.
2) Hang the Sign Boards (L) (R) on the side joints (L) (R).
3) Slide the Sign Boards (L) (R) to the back, and fasten to the cabinet using two
security screws (M6x20).
Lower Height (Total height: 2,140mm)
1) Remove the two hex head screws (M6x20), and remove the side joints (L) (R).
2) Turn the side joint top to bottom, and refit the side joint using the lower two of the
three fixing holes.3 
						

							Page 1-3 Connecting the Seat Assemblies to the Tower Assembly
1) Insert the seat assembly from the side of the tower unit so that the front legs of
the tower unit are underneath the seat assembly.
2) Remove the four security screws (M5x12) from the bottom front of the tower unit,
and remove the lower front cover (F). Temporarily fasten the seat unit with two
hex head bolts (M10x25), flat washers and safety washers. (Do not tighten)
3) Remove the four security screws (M5x12) from the bottom rear of the tower unit,
and remove the lower rear cover (S). Temporarily fasten the ride unit with four
hex head bolts (M10x25), flat washers and security washers.
4) Tighten all of the hex head bolts (M10x25).
5) Connect the connectors between the seat assembly and tower unit.
6) Connect the other seat assembly in the same way.
7) Replace the front and rear covers (F), (S)  taking care not to trap or pinch any
wiring.
[NOTE]: When connecting the seat asseblies to the tower unit take care not to
trap any wires.
4 
						

							Page 8) Insert the front rubber brackets (L), (R) of the tower unit in the side panel of the
seat assembly, and fasten them with two security screws (M5x16) and two
No6X½ pozi flange head screws.
9) Remove the five security screws (M5x16) from the tower side support.
10) Fit the rear safety rubbers to the tower unit with the retaining bracket and the five
security screws (M5x16) previously removed from the tower side support.
11) Place the left, centre, and right safety warning mats in their correct positions.
12) When the machine is in its final location, lower the level adjusters (17 adjusters)
with a spanner so that all castors are raised from the floor.
13) Tighten the lock nuts with a spanner to ensure that the level adjusters not move.5