NEC Gt1150 Lcd Projector Users Manual

E Ð 42
Noise Reduction  (not available for RGB and PC Card Viewer)
You can select three levels video noise reduction.
NOTE: The lower the Noise Reduction level, the better the image quality by wayof higher video bandwidth.
Image Options
Keystone
This feature corrects the keystone (trapezoidal) distortion to make
the top of the screen longer or shorter to be the same as the bottom.
Use the 
§ or © buttons on the slide bar to correct the keystone
(trapezoidal) distortion.
Keystone distortionNormal
NOTE:
1)...

E Ð 43
First select an appropriate color matrix to fit your component signal for
HDTV or SDTV. Then select an appropriate matrix type from B-Y/R-Y,
Cb/Cr or Pb/Pr.
White Balance (not available for PC Card Viewer)
This allows you to adjust the white balance. Brightness for each color
(RGB)is used to adjust the black level of the screen;
Contrast for each color (RGB)to adjust the white level of the screen.
First use the s or t buttons to select R, G, or B for the brightness and
the contrast. Next use the...

E Ð 44
Factory Default
Changes all adjustments and setting to the factory preset for each
source individually except Lamp Hour Meter, Projector Usage, Lan-
guage and Communication Speed. (To reset the lamp usage time, see
Clear Lamp Hour Meter on page E-48.)
All Data ............... Reset all the settings for all the signals to the factory
preset.
Current Signal ..... Resets the adjustments for the current signal to the fac-
tory preset levels.
The items that can be reset for the currently projected...

E Ð 45
1. Open the On/OFF Timer window.
2. Select EDIT and press ENTER on the remote control to open the
EDIT window.
3. Set the Week, Day, On-Time and Off-Time using the Select buttons
and Source buttons (1 thru 10). To cancel the on-time or off time,
use Delete.
4. Select Set and press the ENTER button on the remote control to
complete the setting. To close, select Close.
5. To enable your setting, select Active on the Execute Switch.
6. Select OK and press the ENTER button on the remote control to...

E Ð 46
[Page 3]
Projector Pointer:
This option is avaiable on the optional presentaion remote control
(PR50KIT) only.
This enables you to select from eight different Pointer icons for the
Pointer button on your remote control.
After moving your Pointer icon to the area you want on the screen,
press the Magnify button on the remote control to enlarge the se-
lected area on the screen.
NOTE: There may be cases where the Pointer function is not available (ex. Anon-interlace signal at 15kHz such as video...

E Ð 47
Setup
Enables you to set operating options.
Press OK to save your changes for all the features of Page1, Page2,
Page3, Page 4, Page5 and Page6.
[Page 1]
Orientation:
This reorients your image for your type of projection.
The options are: desktop front projection, ceiling rear projection,
desktop rear projection, and ceiling front projection.
Background:
Use this feature to display a blue/ black screen or logo when no
signal is available. The default background is blue. You can change
the logo...

E Ð 48
[Page 4] Signal Select (RGB connector):
Allows you to choose VIDEO or S-VIDEO for RGB 1 or 2 con-
nector.
Normally select Auto. [Page 3]
Auto Adjust (RGB Only):
When Auto Adjust is set to On, the projector automatically de-
termines the best resolution for the current RGB input signal to
project an image using NECs Advanced AccuBlend Intelligent Pixel
Blending Technology.
The image can be automatically adjusted for position and stability;
Horizontal Position, Vertical Position, Clock, Phase, and...

E Ð 49
[Page 5]
Remote Sensor:
This option determines which remote sensors on the projector are
enabled in wireless mode.
The options are: front, rear, right, or left. All checked boxes indicate
that they can accept the infrared signal from the supplied remote
control.
S-Video Mode Select:
This feature is used to select the S-Video signal detection mode.
This allows identifying of the S-Video signals with different aspect
ratio (Zoom signal 16:9, Wide Zoom signal 4:3).
S2 ................ Identifies Zoom...

E Ð 50 Tools
Provides tools for capturing images and displaying files in a PC Card.
NOTE: The Capture and PC Card Files features are required for a PC card.
Capture:
Allows you to capture an image from a source that is currently be-
ing displayed. The image is saved as JPEG in the PC card.
When you select Capture from the menu, you will get a tool bar. You
can capture an image directly using the tool bar when the menu is
not displayed.
Freeze
Exit
Capture
The tool bar includes the following buttons:...

E Ð 51 Help
Contents:
Provides an online help about how to use the menus. An under-
lined link means that you can move to an adjustment item directly.
Selecting the underlined link and pressing ENTER moves to the
corresponding adjustment item.
NOTE: The Help Menu may not be displayed correctly when a UXGA signalis displayed.
Information:
Displays the status of the current signal, and the lamp and the pro-
jector usage hours.
This dialog box has six pages.
[Page 1]
Source Name
Input Terminal
Entry No....