NEC Gt2000 Lcd Projector Users Manual

E-31
Operating Multiple Projector with Remote Control
You can operate as many as 64 projectors with the same remote control in wireless operation.
To do so:
1. Select [Settings Menu]®[Projector ID] under the main menu and assign an ID number to each projector.
2. Specify the remote ID number to the projector to be used. To do, press and hold the CTL and press Adr button to enter the ID
number.
You can operate the projector assigned the same ID number as the remote address.
Projector ID= 01Projector ID=...

E-32
EX CO
8/
EX C1
EXT-CTL3
15
EX ENPOWER
14
EX PW
1ch
2ch 3ch 5
Console Control Unit Setup Example
* This example is when power is ON and channel 1, 2, and
3 switching is activated. The circuit setup is valid when
the contacts of any of the switches are closed.
Small signal Silicone diodes are used.
* Switchs cannot be pressed simultaneously.
* Channel number means slot number on the ISS-6020.
EMOTE 1B 1 AUDIO
REMOTE 2/PC
EXT-CTLREMOTE
OUTPUT REMOTE
INPUT NO R
51423
10
11 12 13 14 156 978
External...

E-33
Setting The Data
When the EX PW pin is low, the power is on; when high, the
power is off.
When the EX MT pin is low, Picture Mute is on; when high,
Picture Mute is off.EX PW
Low
High Power
ON
OFF
Note: Channel settings are only valid when the ISS-6020 is connected.
Note: If a channel is switched to another using the remote control when the external control is valid, the channel is forced to switch to
the one set by the external control.
Connecting A Single ISS-6020 Switcher
Slot
1
2
3
4
5
6
7
8
9...

E-34
OPERATION4
(OFF) (ON)
STATUS
POWER
ON / OFF
STATUS
POWER
ON / OFF
OFF
ON POWER
RGB1 RGB2VIDEO/S-VIDEO
Each press toggles between S-
VIDEO and VIDEO.
VOLUME
The volume increases.
The volume decreases.
Volume
Ð+  32
General Controls
Getting started
This section describes the basic operation of the projector.
The operation may differ depending on the makeup of the
projector system; therefore, please follow the directions of
your system administrator.
Operation using the remote control is described...

E-35
+
-
FOCUS ZOOM
W
T
OFF
ON POWER
STATUS
POWER
ON / OFF
(OFF) (ON)
STATUS
POWER
ON / OFF
5. Adjust the Screen Size and then Adjust the Focus
When the projector is set up permanently, there is no need to
make the usual adjustments.
(The Zoom and Focus buttons do not function on GT2000R.)
A) Press the ZOOM W/T button and adjust the screen size.
B) Press the FOCUS +/- button and adjust the focus.
6. Adjust the Screen and Picture (Only When Required)
When the screen is not displayed properly, adjust the...

E-36
Main Menu
Picture
Alignment
Memory
Switcher
Display Menu
Settings Menu
SourceSettings Menu
Language
Background
Auto Start
Auto Save
Onscreen Mute
Switcher Control
Ext. Control
Projector ID
Sync Termination
Projection
Keystone
Keystone Save
English
Currently selected
item Setting at Time of
Factory Shipping
English
Blue back
Off
Off
Off
Standalone
Off
00
Hi-impedance
Front Floor
00
Off
Language
English
Deutsch

Italianno
Espanol
Svenska
SETUP (Various Settings)
Please make settings in conjunction...

E-37
Background
Blue
Black
Auto Start
On
Off
Auto Save
On
Off
Onscreen Mute
On
Off
Selecting the Background Color When There Is
No Signal [Background]
This is the setting of the background color when there is no input
signal.
1. Select [Settings Menu] ® [Background] from the main menu.
2. Press the cursor s/t button and select the background color, then
press the ENTER button to set.
Blue...The background color will be blue.
Black...The background color will be black.
Selecting Auto Start [Auto Start]...

E-38
The term switcher refers to the NEC ISS-6020 Switcher.
Switcher Control
Standalone
SW 1 Level
SW 2 Level
Ext. Control
On
Off
Projector ID
No.0 - 64
Selecting the Switcher Control Method [Switcher
Control]
The switcher is a unit that switches the input equipment when a
number of different video devices or computers are connected.
When the REMOTE 1 connector is used, input selection and
adjustment are permitted by the projector. See Using User
Memory and Channel Memory on Page E-56.
See (Connections...

E-39
Sync Termination
75W
Hi-Z
Projection
Front Floor
Rear Ceiling
Rear Floor
Front Ceiling
Sync Signal Termination Setting
[Sync Termination]
This sets the impedance of the RGB/YCbCr Input 1 connector.
This function sets whether or not the unit will accommodate a 75
ohm output (specification) impedance of the video or personal
computer equipment.
1. Select [Settings Menu] ® [Sync Termination] from the main
menu.
2. Press the cursor s/t button and select the termination resistance
value, then press the...

E-40
[Keystone distortion] [No distor tion]
Keystone Save
On
Off Settings Menu
Language
Background
Auto Start
Auto Save
Onscreen Mute
Swithcer Control
Ext. Control
Projector ID
Sync Termination
Projection
Keystone
Keystone Save
Ð+  Ð10
Normalize?
Keystone
Ye s
No
Selecting Correction and Storage of Keystone
Distortion [Keystone]
Keystone distortion arises when the angles are off between the
projector and screen in the vertical orientation at the time of setting
up the projector. The keystone function is...