NEC Gt6000 Lcd Projector Users Manual

							1-7
3D REFORM3D A
SELECT
LENS SHIFT
FOCUS ZOOMDOWN LEFT RIGHTUP
Z
STATUS PC CARD 2 PC CARD 1 LAMP 1 LAMP 2 POWER
ON/STAND BY
AUTO ADJUST
MENU
ENTERCANCEL
F
1 7
2 3 546 13 14 118 9 12
10
Top Features
1. POWER Button (ON / STAND BY)(  )Use this button to turn the power on and off when the main
power is supplied and the projector is in standby mode or idle
mode.
NOTE: To turn on or off the projector, press and hold this button for a minimumof two seconds.
2. POWER IndicatorWhen this indicator is green, the projector is on; when this
indicator is orange, it is in standby or idle mode. See the Power
Indicator section on page 10-3 for more details.
3. STATUS IndicatorIf this light blinks red rapidly, it indicates that an error has oc-
curred, the lamp cover is not attached properly or the projector
has overheated. If this light remains orange, it indicates that
you have pressed a cabinet key while the Control Panel Key
Lock is enabled. See the Status Indicator section on page 10-
3 for more details.
4. LAMP Indicator 1/2If this light blinks red rapidly, it's warning you that the lamp has
reached the end of its usable life. After this light appears, re-
place the lamp as soon as possible (See page 9-2). See the
Lamp Indicator section on page 10-3 for more details.
5. PC CARD Access Indicator 1/2Lights while accessing a PC card.
6. 3D REFORM ButtonPress this button to enter 3D Reform mode to correct the key-
stone (trapezoidal) distortion, and make the image square.
Press to toggle between Cornerstone and Keystone adjust-
ment mode.
NOTE: Pressing and holding this button for a minimum of 2 seconds will reset3D Reform correction setting values to zero.
7. AUTO ADJUST ButtonUse this button to adjust Position-H/V and Pixel Clock/Phase
for an optimal picture. See page 3-6.
8. MENU ButtonDisplays the menu.
9. SELECT 
 (+) (–) / Volume Buttons
 : Use these buttons to select the menu of the item you
wish to adjust. When no menus appear, these buttons
work as a volume control.
: Use these buttons to change the level of a selected menu
item. A press of the button executes the selection. When
the menus or the Viewer tool bar is not displayed, these
buttons can be used to select a slide, or to move the
cursor in Folder List or Slide List.
10. ENTER ButtonExecutes your menu selection and activates items selected
from the menu.
11. CANCEL ButtonPress this button to exit "Menus". Press this button to return
the adjustments to the last condition while you are in the ad-
justment or setting menu.
12. LENS SHIFT 
ButtonAdjust the lens offset by shifting the projected image position
horizontally and / or vertically.
13. ZOOM Button (+/-)Zoom the lens in and out.
14. FOCUS Button (+/-)Adjust the lens focus.
1. Introduction 
						

							1-8
1. Introduction
AUDIO
AUDIO
AUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/
   HV
R
L/MONO
R
L/MONO
R
L/MONO L/MONO
SLOT 1 SLOT 2
DVI
RGB OUT
RGB 1
RGB 2
VIDEOS-VIDEO
3
8 1 2
4
56 7
Terminal Panel Features
1. RGB 1 Connectors [R/Cr, G/Y, B/Cb, H/V, V] (BNC)
Connect R,G,B,H (Horizontal sync) and V (Vertical sync) out-
puts of external equipment.
If using a component with a combined sync (SYNC) output,
connect it to the H/V terminal. When using luminance and color-
difference signals of HDTV and DVD, connect Pr/Cr to the R, Y
to the G and Pb/Cb to the B input of the projector.
RGB 1 Audio Input Jacks (RCA)
L/MONO: This is your left channel audio input for stereo sound
coming from the RGB Input 1 source.
This also serves as your monaural audio input.
R: This is your right channel audio input for stereo sound from
the RGB Input 1 source.
2. RGB 2 Connector (Mini D-sub 15 Pin)
Connect your computer or other analog RGB equipment such
as IBM compatible or Macintosh computers. This also serves
as a component input connector that allows you to connect a
component video output of component equipment such as a
DVD player. This connector also supports SCART output sig-
nal. See page 2-9 for more details.
RGB 2 Audio Iput Mini Jack (Stereo Mini)
This is where you connect audio output from your computer or
DVD player connected to the RGB2 input. A commercially avail-
able audio cable is required.
3. DVI IN Connector (DVI-D 24 Pin)
This connector can be used to accept digital signal output from
a computer with a DVI connector.DVI AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your com-
puter when connected to the DVI input. A commercially avail-
able audio cable is required.
4. RGB OUT Connector (Mini D-Sub 15 Pin)
You can use this connector to loop your computer image to an
external monitor from the RGB 1 or 2 input source.
5. VIDEO IN Connector (BNC)
Connect a VCR, DVD player, laser disc player, or document
camera here to project video.
VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo
sound from a Video source.
6. S-VIDEO IN Connector (Mini DIN 4 Pin)
Here is where you connect the S-Video input from an external
source like a VCR.
NOTE: S-Video provides more vivid color and higher resolution than the tradi-tional composite video format.
S-VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo
sound from an S-Video source.
7. AUDIO OUT Jacks R/L (RCA)
You can use this connector to output sound from the currently
selected input source (RGB 1, RGB 2, DVI (DIGITAL), Video
or S-Video).
Output sound level can be adjusted in accordance with the
sound level of the internal speaker.
8. Slot 1/2
For optional RGB, SDI or DVI board. 
						

							1-9
USB (MOUSE/HUB)USB (PC)PC CARD2
1
PC CONTROL
IN
IN OUT
OUT SC TRIGGER REMOTE 2REMOTE 1LAN
AC IN 
12 3
7 4
8
9
10 11 5
6
1. USB Port [MOUSE/HUB] (Type A)
Connect a USB mouse. You can operate the menu or Viewer
with a USB mouse via this port.
• A USB-supported scanner or PC peripheral can be connected
to this port. (USB Hub Function. See page 4-3)
2. USB Port [PC] (Type B)
Connect this port to the USB port (type A) of your PC using a
USB cable. This port also serves as a PC Control port by using
Dynamic Image Utility 2.0 included on the supplied CD-ROM.
3. PC CARD Slot 1/2
Insert a PC card, commercially available flash memory card or
NEC optional wireless LAN card here.
There are two slots: Slot 1 and Slot 2.
4. PC CARD Eject Button 1/2
Press to eject a PC card partially. Each slot has its own eject
button: 1 and 2.
5. PC CONTROL Connectors (D-Sub 9 pin)
For system expansion such as PC-Control using Dynamic Im-
age Utility included on the supplied User Supportware CD-
ROM or RS232C control from an external control system.
IN: connect to the external equipment such as a PC or control
system.
OUT: for daisy-chaining multiple projectors and operating them
with the same external equipment. To do so, connect to a sec-
ond projector’ s IN terminal to relay the input at the IN terminal
of the first projector until all the projectors are connected.6. SC. TRIGGER Mini Jack
When the projector is powered ON the screen trigger output
sends a low voltage trigger to the screen controller and the
screen will go down. When the projector is powered OFF the
screen trigger stops sending a low voltage trigger to the screen
controller and the screen will go up.
NOTE: To use this feature, you must turn on the Screen Trigger function. Seepage 8-17.
Terminal Panel Features
1. Introduction
Tip (12V)
Ring (0V)
Sleave (ground. 0V) Stereo mini cable
(not supplied)
NOTE: Screen controllers are supplied and supported by screen manufacturers.
NOTE: Do not use this jack for anything other than intended use. Connecting the
wired remote control to the SC. TRIGGER Mini Jack causes damage to the re-
mote control.
7. LAN Port (RJ-45)
This port is typically used for UTP Ethernet/Fast Ethernet. Use
this connector to control the projector on a LAN. See page
2-12.
8. REMOTE 1 (Mini D-Sub 15 Pin)
This terminal allows external control of the projector by use of
contact closure. See page 10-9.
9. REMOTE 2 Mini Jacks (IN/OUT)
IN: wired remote control input.
OUT: for daisy-chaining multiple projectors and operating them
with the same remote control. To do so, connect to a second
projector’ s IN terminal to relay the input at the IN terminal of
the first projector until all the projectors are connected.
10. Main Power Switch
When you plug the supplied power cable into an active wall
outlet and turn on the Main Power switch, the POWER indica-
tor turns orange and the projector is in standby mode. See
page 3-2.
11. AC IN
Connect the supplied power cable’s three-pin plug here.
Three types of power cable are supplied with this projector:
three-pin type for U. S. A. and Canada. Two-pin type for Europe
and Japan. 
						

							1-10
1. Introduction
OFF
+-
PICTUREADJUSTABC DEFGHI
JKL MNO PQR
STU
,.
UNDO CANCEL
TEST
PICTUREKEYSTONE AMPLITUDE ENTRYLISTSOUND OSD
MUTE
MAGNIFYHELP INFO.
POSITION AUTOPIXELVWX YZ/
WHITE BAL.IMAGE
ON POWER
MENU
ENTER
123
456
7
089
ADDRESS
PROJECTOR
RGB
LENS
SHUTTER
BS
+
-
+
-
FOCUSZOOM
CTLLENS
2
5
6
7
9
10
12
13
17
20
21
22
24
262
5
23
19
18
16
15
14
11 8 4 3 1
v Remote Control Features1. POWER ON
Press and hold this button for a minimum of two seconds to
turn on the projector when the main power is supplied and the
projector is in standby mode or idle mode.
2. POWER OFF
Press and hold this button for a minimum of two seconds to
turn off the projector.
3. MENU
Press to display the main menu.
While pressing and holding CTL, press this button to display
the Remote Control ID dialog box to specify the remote control
ID. See page 7-2.
4. ENTER
Executes the menu selection and activates items selected from
the menu. When the slider or dialog box is displayed:
Pressing this button confirms adjustments/setting and returns
to the previous menu display.
5. Select (Up/Down/Left/Right)

: Use these buttons to select the menu of the item you
wish to adjust.
When no menus appear, these buttons work as a volume
control.
: Use these buttons to change the level of a selected
menu item.
A press of the  button executes the selection.
Pressing and holding CTL, then pressing button works as a
Back Space key in the entry screen.
Pressing and holding CTL, then pressing this button moves
the menu, slider, toolbar or dialog box.
6. ADJUST WHITE BAL.
Press to display the Picture Management screen.
7. ADJUST PICTURE
Press to display the Picture adjustment screen. Pressing this
button sequentially selects adjustment screens.
8. IMAGE/PROJECTOR
Press to display the Image Option screen. Pressing this button
sequentially selects Image Options screens.
While pressing and holding CTL, pressing this button rotates
Projector Options screens.
9. Source / Input
Press to select input or to name a signal.
1 Selects RGB 1 input.
2 Selects RGB 2 input.
3 Selects DVI (DIGITAL) input.
4 Selects VIDEO input.
5 Selects S-VIDEO input.
6 Selects Viewer input
7 Selects LAN input
8 Selects OPTION SLOT 1* (available for optional SDI board)
9 Selects OPTION SLOT 2* (available for optional SDI board)
0 Sequentially selects: RGB1 (VIDEO) 
→RGB1 (S-VIDEO) .
* This button toggles between input 1 and 2.
NOTE: While pressing and holding CTL, pressing this button switches to theselected signal found in the Entry List. 
						

							1-11
1. Introduction
OFF
+-
ICTUREADJUSTBCDEFM
WHITE BAL.IMAGE
ON POWER
MENU
ENTER
2
ADDRESS
PRO
BS
27
28
10. UNDO
Press to return the adjustments and settings to the previous
condition. While pressing and holding CTL, pressing this but-
ton clears the entire menus or adjustment/setting screen. At
this time the adjustments/settings are stored in memory ex-
cept the items on the setting screen with "OK" and "Cancel"
buttons such as the Menu and the Setup screen.
11. CANCEL
Press to exit the menu.
Press this button with CTL to return to the previous menu with-
out closing adjustment/setting screen while the menus appear.
This feature allows you to adjust or set several items concur-
rently.
12. INFO
Displays the "Source Information" or "Projector Information"
window. This button toggles between these two windows.
While pressing and holding CTL, pressing this button stores
lens position settings.
13. TEST
Press to display the test pattern. Pressing this button sequen-
tially selects test patterns.
14. HELP
Provides online help.
15. PIXEL
Displays the Position/Clock screen to adjust the clock and
phase.
16. AUTO (RGB only)
Press to adjust Position-H/V and Pixel Clock for an optimal
picture.
17. POSITION
Press to display the Position screen; press again to display the
Blanking screen.
While pressing and holding CTL, pressing this button displays
the Lens Shift adjustment screen.
18. MUTE SOUND
Turns off the sound for a short period of time. Press again to
restore the sound.
19. MUTE OSD
Press to turn off the on-screen display. Press again to restore
the on-screen display.
NOTE: You can also turn off the on-screen display forcibly by pressing and
holding CTL and then pressing MUTE OSD (Forced On-Screen Mute Mode) ;
doing this again restores it. In this case any adjustment will still change the
projector's memory settings. This mode is available even when input is switched
to another or the power is turned off the main power.
20. MUTE PICTURE
Press to turn off the picture for a short period of time. Press
again to restore the picture.
21. KEYSTONE (R)
Press to display the Keystone Correction (3D Reform) screen.
This button toggles between “Cornerstone” and “Keystone”.
When the test pattern is displayed, while pressing and holding
CTL, pressing this button displays a red test pattern.
NOTE: Pressing and holding this button for a minimum of two seconds willreset 3D Reform correction setting values to zero.
22. AMPLITUDE (G)
Service personnel only.
When the test pattern is displayed, while pressing and holding
CTL, pressing this button displays a green test pattern.
23. ENTRY LIST (B)
Press to display the Entry List screen.
Pressing and holding CTL and then ENTRY LIST buttons si-
multaneously, enters a signal in the Entry List when you are
not displaying a test pattern.
When the test pattern is displayed, while pressing and holding
CTL, pressing this button displays a blue test pattern.
24. FOCUS (+/–)
While pressing and holding CTL, pressing this button allows
you to adjust the lens focus.
25. MAGNIFY/ZOOM (+/–)
Magnify the size of a target por tion.
While pressing and holding CTL, pressing this button allows
you to zoom the lens in and out.
26. CTL
Used in conjunction with other buttons, similar to a shift key on
a computer.
27. Remote Jack
Connect your remote cable here for wired operation.
28. Infrared Transmitter
Direct the remote control toward the remote sensor on the pro-
jector cabinet. 
						

							1-12
1. Introduction
7m30˚
30˚
Remote Control Precautions
• The remote control system may not function when direct sunlight or
strong illumination strikes the remote control sensor of the main unit, or
when there is an obstacle in the path.
• When remote control buttons are pressed and held, projector’s function
keys may not operate.
• Do not subject to strong shock.
• Do not allow water or other liquid to splash on the remote control. If the
remote control gets wet, wipe it dry immediately.
• Avoid exposure to heat and steam.
• Remove the batteries from the remote control when the remote control
is not going to be used for a long period.
Remote Control Battery Installation
Installing the Remote Control Batteries
When it comes time to replace the batteries, two "AAA" type will
be required.
1. Press and open the cover.
2. Align and insert the batteries according to the (+) and (-) indications
inside the case.
3. Replace the cover.
Operating Range for Wireless Remote Control
The infrared signal operates by line-of-sight up to a distance of
approximately 7m (20 feet) and a 60 degree angle of the remote
sensor.
The projector will not function if there are objects between the
remote sensor and the remote control or if strong light falls on
the remote sensor. Weak batteries will also prevent the projector
from operating properly.
Remote sensors on the
projector cabinet Side View
7m
Remote control
NOTE: You cannot operate the projector using the remote control if:
• The remote control ID is not set to [None].
• The remote ID is not the same as the projector ID.
See page 7-2 for setting remote ID and projector ID. 
						

							1-13
AUDIO
AUDIOAUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/
  HV
RL/MONO
RL/MONORL/MONOL/MONO
SLOT 1 SLOT 2DVI
RGB OUT
RGB 1
RGB 2
VIDEOS-VIDEO
USB (MOUSE/HUB)USB (PC)PC CARD2
1
PC CONTROL
IN
IN OUT
OUT SC TRIGGER REMOTE 2REMOTE 1LAN
AC IN 
REMOTE 2 
IN
OFF+-PICTUREADJUSTABC DEFGHI
JKL MNO PQR
STU
,.
UNDO CANCEL
TESTPICTUREKEYSTONE AMPLITUDE ENTRYLISTSOUND OSDMUTE
MAGNIFYHELP INFO.
POSITION AUTOPIXELVWX YZ /WHITE BAL.IMAGEON POWERMENU
ENTER123
456
7
089ADDRESSPROJECTORRGB
LENSSHUTTERBS+-+-
FOCUSZOOMCTLLENS
Using the Remote Control in Wired Operation
Connect one end of the supplied remote cable to the REMOTE 2 IN
mini jack and the other end to the remote jack on the remote control.
NOTE: Do not use this jack for anything other than intended use. Connecting the wiredremote control to the SC. TRIGGER Mini Jack causes damage to the remote control.
Terminal panel (Right)
Remote cable (supplied)
1. Introduction 
						

							2-1
2
Installation
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
z Setting Up Your Projector .......................................... 2-2
Screen Size and Projection Distance .................................................................. 2-2
x Lens Shift Adjustable Range .................................... 2-4
c Optional Lens Installation ......................................... 2-6
v Making Connections ............................................... 2-13
Connecting Your PC or Macintosh ..................................................................... 2-13
To connect Scart Output ............................................................................... 2-14
Connecting an External Monitor ........................................................................ 2-14
Connecting Your DVD Player ............................................................................. 2-15
Connecting Your VCR or Laser Disc Player ....................................................... 2-16
Connecting to a Network ................................................................................... 2-17
Connecting the Supplied Power Cable .............................................................. 2-18 
						

							2-2
List of Screen Sizes
Screen size Width (H) Height (V)m inch m inch40" 0.8 31.5 0.6 23.660" 1.2 47.2 0.9 35.480" 1.6 63.0 1.2 47.2100" 2.0 78.7 1.5 59.1120" 2.4 94.5 1.8 70.9150" 3.0 118.1 2.3 90.6200" 4.1 161.4 3.0 118.1250" 5.1 200.8 3.8 149.6300" 6.1 240.2 4.6 181.1400" 8.1 318.9 6.1 240.2500" 10.2 401.6 7.6 299.2
Formulas: Screen width H (m)= Screen size
4/5
0.0254
Screen height V (m)= Screen size
3/5
0.0254
Screen width H (inch)= Screen size
4/5
Screen height V (inch)= Screen size
3/5Width Height
Screen size (Diagonal) Screen Size and Projection Distance
Applicable lens and throw distance/ List of screen sizes This chapter describes how to set up your projector and how to connect video and audio sources.
z Setting Up Your Projector
Your Projector is simple to set up and use. But before you get started, you must first:
1. Determine the image size
2. Set up a screen or select a non-glossy white wall onto which you can
project your image.
3. Install the optional lens to the projector.4. Connect the supplied power cable.
5. Set up the projector.
6. Connect a PC, VCR, DVD player, or other equipment.
7. Make settings or adjustments on the projector.
Table of Throw Distances and Screen Sizes for Optional Lenses
2. Installation
40"
60"
67"
72"
80"
84"
90"
100"
120"
150"
180"
200"
210"
240"
250"
270"
300"
400"
500"0.44
0.70
0.78
0.85
0.95
1.00
1.07
1.20
1.4517.5
27.4
30.8
33.3
37.3
39.2
42.2
47.1
57.00.76
1.17
1.31
1.41
1.58
1.66
1.78
1.99
2.39
3.01
3.62
4.02
4.23
4.84
5.0430.0
46.1
51.7
55.7
62.1
65.3
70.2
78.2
94.2
118.3
142.4
158.5
166.5
190.6
198.60.91
1.39
1.57
1.69
1.88
1.98
2.13
2.37
2.86
3.59
4.33
4.82
5.06
5.79
6.04
6.53
7.26–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–1.33
2.03
2.27
2.45
2.73
2.87
3.08
3.43
4.13
5.18
6.23
6.93
7.28
8.33
8.68
9.38
10.4335.7
54.9
61.7
66.5
74.2
78.0
83.8
93.4
112.7
141.5
170.4
189.6
199.3
228.1
237.8
257.0
285.9–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–52.3
79.9
89.5
96.4
107.4
113.0
121.2
135.0
162.6
203.9
245.2
272.8
286.6
327.9
341.7
369.2
410.60.91
1.40
1.57
1.70
1.89
1.99
2.14
2.38
2.87
3.60
4.33
4.82
5.07
5.80
6.04
6.53
7.27–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–1.15
1.75
1.97
2.12
2.36
2.48
2.66
2.96
3.57
4.48
5.38
5.99
6.29
7.20
7.50
8.11
9.0136.0
55.2
62.0
66.8
74.5
78.3
84.1
93.7
112.9
141.8
170.6
189.9
199.5
228.4
238.0
257.2
286.1–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–45.2
69.0
77.4
83.3
92.9
97.6
104.8
116.7
140.5
176.2
212.0
235.8
247.7
283.4
295.4
319.2
354.91.30
1.99
2.23
2.40
2.68
2.82
3.02
3.37
4.06
5.10
6.14
6.83
7.17
8.21
8.56
9.25
10.28–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–1.74
2.65
2.97
3.19
3.56
3.74
4.01
4.47
5.38
6.74
8.11
9.02
9.47
10.84
11.29
12.20
13.5751.0
78.3
87.8
94.6
105.5
110.9
119.1
132.7
159.9
200.7
241.6
268.8
282.4
323.2
336.8
364.0
404.9–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–68.4
104.2
116.7
125.7
140.0
147.2
158.0
175.9
211.7
265.4
319.2
355.0
372.9
426.7
444.6
480.4
534.11.53
2.34
2.62
2.83
3.15
3.32
3.56
3.97
4.78
6.00
7.22
8.04
8.44
9.66
10.07
10.88
12.10–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–2.03
3.10
3.47
3.74
4.16
4.38
4.70
5.23
6.30
7.90
9.50
10.56
11.10
12.69
13.23
14.29
15.8960.1
92.1
103.3
111.3
124.1
130.6
140.2
156.2
188.2
236.3
284.3
316.3
332.4
380.4
396.4
428.5
476.5–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–80.0
122.0
136.7
147.2
164.0
172.4
185.0
205.9
247.9
310.9
373.9
415.8
436.8
499.8
520.8
562.8
625.72.58
2.90
3.12
3.48
3.66
3.93
4.38
5.28
6.64
7.99
8.89
9.34
10.69
11.14
12.04
13.40
17.90–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–3.86
4.32
4.66
5.19
5.45
5.85
6.52
7.84
9.83
11.83
13.15
13.82
15.81
16.47
17.80
19.79
26.43101.6
114.0
122.9
137.1
144.2
154.8
172.6
208.0
261.3
314.5
350.0
367.7
421.0
438.7
474.2
527.4
704.9–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–152.0
170.3
183.3
204.3
214.7
230.4
256.5
308.8
387.2
465.6
517.9
544.0
622.4
648.6
700.8
779.2
1,040.6
5.10
5.36
5.76
6.41
7.73
9.71
11.69
13.01
13.67
15.64
16.30
17.62
19.60
26.19
32.79–
–
–
–
–
–
–
–
–
–
–
–
–
–
–7.81
8.21
8.81
9.81
11.81
14.80
17.80
19.79
20.79
23.79
24.78
26.78
29.78
39.76
49.74200.6
211.0
226.6
252.5
304.5
382.3
460.2
512.1
538.1
615.9
641.9
693.8
771.7
1,031.2
1,290.8–
–
–
–
–
–
–
–
–
–
–
–
–
–
–307.6
323.3
346.9
386.2
464.8
582.7
700.6
779.2
818.5
936.5
975.8
1,054.4
1,172.3
1,565.3
1,958.47.68
8.08
8.68
9.68
11.69
14.70
17.71
19.72
20.72
23.74
24.74
26.75
29.76
39.79
49.83–
–
–
–
–
–
–
–
–
–
–
–
–
–
–11.50
12.10
12.98
14.47
17.43
21.87
26.31
29.28
30.76
35.20
36.68
39.64
44.09
58.90
73.71302.3
318.1
341.8
381.3
460.3
578.9
697.4
776.4
815.9
934.5
974.0
1053.0
1171.5
1566.7
1961.8–
–
–
–
–
–
–
–
–
–
–
–
–
–
–452.9
476.2
511.2
569.5
686.1
861.0
1036.0
1152.6
1210.9
1385.8
1444.1
1560.8
1735.7
2318.8
2901.9
(m)0.6 1.0 1.2 – 1.7 1.2 – 1.5 1.7 – 2.2 2.0 – 2.6 2.2 – 3.2 3.2 – 4.8 4.8 – 7.1 GT06RLB GT10RLB GT12ZLB GT13ZLB GT19ZLB GT20ZL GT24ZLB GT34ZLB GT48ZLB
(inches) (m) (inches) (m) (m)(inches) (inches) (m) (inches) (m) (inches) (m) (inches) (m) (inches) (m) (inches) 
						

							2-3
GT34ZLB (H
3.2) - (H
4.8)
GT24ZLB (H
2.2) - (H
3.2)
GT20ZL (H
2.0) - (H
2.6)
GT13ZLB (H
1.2) - (H
1.5)
GT12ZLB (H
1.2) - (H
1.7)
GT10RLB (H
1.0) GT06RLB (H
0.6)
GT48ZLB (H
4.8) - (H
7.1)
GT19ZLB (H
1.7)
 (H
2.2)
Throw distance
For screen sizes between 40" and 500" not indicated on the above table, use formulas below.
Projection Distance= Screen Width (H) 
 Lens Magnification
Throw distance for GT06RLB (m/inch) = H 
 0.6  Distance from 0.4m to 1.5m / 17.5" to 57.00"
Throw distance for GT10RLB (m/inch) = H 
 1.0  Distance from 0.8m to 5.0m/30.0" to 198.6"
Throw distance for GT12ZLB (m/inch) = H 
 1.2 through H 
 1.7  Distance from 0.9m to 10.4m / 35.7" to 410.6"
Throw distance for GT13ZLB (m/inch) = H 
 1.2 through H 
 1.5  Distance from 0.9m to 9.0m/36.0" to 354.9"
Throw distance for GT19ZLB (m/inch) = H 
 1.7 through H 
 2.2  Distance from 1.3m to 13.6m/51.0" to 534.1"
Throw distance for GT20ZL (m/inch) = H 
 2.0 through H 
 2.6  Distance from 1.5m to 15.9m/60.1" to 625.7"
Throw distance for GT24ZLB (m/inch) = H 
 2.2 through H 
 3.2  Distance from 2.6m to 26.4m/101.6" to 1040.6"
Throw distance for GT34ZLB (m/inch) = H 
 3.2 through H 
 4.8  Distance from 5.1m to 49.7m/200.6" to 1958.4"
Throw distance for GT48ZLB (m/inch) = H 
 4.8 through H 
 7.1  Distance from 7.7m to 73.7m / 302.3" to 2901.9"
NOTE: Distances may vary +/-5%.
NOTE: GT10RLB and GT06RLB should be used only for “zero degree/no-offset” applications.
 To set zero degree/no-offset, reset the lens position by using "Return to  Factory Default" in "Ref. Lens Memory."
 See page 8-13 for using "Return to Factory Default" to reset the lens position.
 After resetting, perform fine adjustment on the lens position by using the LENS SHIFT button 
.
NOTE: When using the projector with either the GT13ZLB or GT12ZLB lens, it is recommended to select "Dual" in the Lamp Settingsmenu. This will provide the bestperformance when operating the projector.
2. Installation
Available combination of optional lens and lamp
* If you want to use the projector in the single lamp, please call for more information.
GT06RLB GT10RLB GT12ZLB GT13ZLB GT19ZLB GT20ZL GT24ZLB GT34ZLB GT48ZLB
Dual Yes Yes Yes Yes Yes Yes Yes Yes Yes
One lamp Yes Yes No No * Yes * * Yes
Lens No
Lamp selection