NEC Gt6000 Lcd Projector Users Manual

							3-6
The confirmation screen is displayed.
On the Cornerstone adjustment screen, select
“Exit” and then “OK”, or press the CANCEL but-
ton on the remote control. 8. Use the SELECT 

button to select another icon which points in
the direction.
Screen
9. Press the SELECT 
orbutton to highlight the [OK] and press the
ENTER button.
This completes the keystone correction.
Selecting “Cancel” will return to the adjustment screen without saving
changes (Step 3).
Selecting "Reset" will return to the factory default.
Selecting "Undo" will exit without saving changes.
NOTE: To return the 3D Reform correction setting values to the factory default,
press and hold the 3D REFORM button on the projector cabinet or the KEYSTONE
button on the remote control for a minimum of 2 seconds.
NOTE: During 3D Reform adjustment, "Aspect Ratio" and "Screen" may not be avail-
able. Should this happen, first reset the 3D Reform data and then do each setting.
Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/or Screen
setting can limit 3D Reform in its adjustable range.
The adjustable ranges for 3D Reform are as follows:
Horizontal ........... Max ±30° approx.
Ver tical ............... Max ±40° approx.
* The following are conditions at the above maximum angle when all of
the following are met
• Image is projected in Wide (Zoom)
• The lens is positioned at the center (when not, adjustable range in-
creases or decreases)
• Resolution is XGA
Higher resolution than XGA limits 3D Reform in its adjustable range.
• Menu items should be set as follows:
Aspect Ratio ............................... 1.33:1 (4:3)
Screen Type ................................ 1.33:1  (4:3)
• Horizontal and Vertical are adjusted separately.
A combination of both adjustments limits 3D Reform in its adjustable
range.
• When “Native” is selected in “Resolution”, “3D Reform” is not available.
3. Projecting an Image
b Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing RGB image automatically
Press the Auto Adjust button to optimize an RGB image automatically.
[Poor picture]
[Normal picture]
Press the AUTO ADJUST or AUTO button to fine-tune the computer im-
age or to remove any ver tical banding that might appear and to reduce
video noise, dot interference or cross talk (this is evident when part of your
image appears to be shimmering). This function adjusts the clock frequen-
cies that eliminate the horizontal banding in the image. This function also
adjusts the clock phase to reduce video noise, dot interference or cross
talk. (This is evident when part of your image appears to be shimmering.)
This adjustment may be necessary when you connect your computer for
the first time.
NOTE:
• Some signals may not be displayed correctly or take time.
• The Auto Adjust function does not work for component or video signals.
• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock
and Phase manually. See page 8-10.
n Turning Up or Down VolumeSound level from the speaker and the AUDIO OUT jack (RCA) on the
projector can be adjusted.
increase volume
Volume bardecrease volume
+-
3D REFORM3D A
SELECT
STATUSLAMP 2 POWER
ON/STAND BY
AUTO ADJUST
MENU
ENTERCANCEL
JKL MNO PQR
STU
,.
UNDO CANCEL
TEST HELPINFO.
POSITION AUTOPIXELVWX YZ /456
7
089
LENS
NOTE: The SELECT 
orbutton works as a volume control only when no menuappears.
NOTE: The volume bar can be dis-
played by selecting “Sound” from “Ba-
sic Menu” or “Advanced Menu”. 
						

							3-7
m Turning off the Projector
To turn off the projector:
First press the POWER (ON/STAND BY) button on the projector cabinet
or the POWER OFF button on the remote control for a minimum of two
seconds. The POWER indicator will glow orange. After the projector turns
off, the cooling fans keep operating for 90 seconds (2 minutes in the op-
tional extended life lamp GT60LPS) (Cooling-off time).
Second, turn off the Main Power switch. The power indicator will go out.
Last unplug the power cable.
NOTE: You cannot turn off the projector for 1 minute immediately after turning onthe projector.
CAUTION
Do not unplug the power cable from the wall outlet or do not turn off
the main power under any one of the following circumstances. Doing
so can cause damage to the projector:
• While the Hour Glass icon appears.
• While the message "Please wait a moment." appears. This mes-
sage will be displayed after the projector is turned off.
• While the cooling fans are running. (The cooling fans continue to
work for 90 seconds (2 minutes in the optional extended life lamp
GT60LPS) after the projector is turned off).
• While accessing a PC card or LAN card. (The PC Card Access in-
dicator lights.)
3. Projecting an Image
OFF
+-
ON POWER
MENU
ENTER
ADDRESSBS
POWERPOWER POWERON/STAND BY
Power onFan working
Standby or Idle
Steady green
lightFlashing orange
lightSteady orange
light 
						

							4
Convenient Features
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
zTurning Off the Image and Sound ............................. 4-2
x Enlarging and Moving a Picture ................................ 4-2
c Getting the On-line Help and Information ................. 4-2
v Using a USB Mouse ................................................. 4-3
b Using a USB HUB Function ...................................... 4-3
n Changing Background Logo ..................................... 4-4
m Making Freehand Drawings on
a Projected Image (ChalkBoard) .............................. 4-4
, Lens Memory ............................................................ 4-5 
						

							4-2
z Turning Off the Image and Sound
Press the MUTE PICTURE button to turn off the image and sound for a
short period of time. Press again to restore the image and sound.
x Enlarging and Moving a Picture
You can enlarge the area you want up to 400 percent.
To do so:
Press the MAGNIFY button.
Enlarge the selected area.
When the MAGNIFY (+) button is pressed, the image is magnified. To
move the magnified image, use the SELECT button.
cGetting the On-line Help and Information
You get the contents about Help.
Display Help
Exit Help
SELECT
Return the image to the original size.
HELP
4. Convenient Features
MAGNIFY
+
-
ZOOM
MAGNIFY
+
-
ZOOM
INFO.
You get the source and projector information.
Press this button once to display “Source Information” and press twice to
display “Projector Information”.
Press third time to close it. Press the MUTE SOUND button to turn off the sound for a short period of
time. Press again to restore the sound.
Press the MUTE OSD button to turn off the on-screen display. Press again
to restore the on-screen display.
PICTURE SOUND OSD
MUTE
PICTURE SOUND OSD
MUTE
NOTE: You can also turn off the on-screen display forcibly by pressing and holding
CTL and then pressing MUTE OSD (Forced On-Screen Mute Mode) ; doing this
again restores it. In this case any adjustment will still change the projector's memory
settings. This mode is available even when switching inputs or the main power is
turned off.
PICTURE SOUND OSD
MUTE 
						

							4-3
v Using the USB Mouse
Using a commercially available USB mouse gives you smooth operation.
NOTE: There may be some brands of USB mouse that the projector does not sup-port.
Operate the Projector Menus using the USB mouse
Mouse CursorWhen connecting a USB mouse to the projector, you get a
mouse cursor on the screen.
Unless you use your USB mouse within 10 seconds, the mouse
cursor disappears.
Menu DisplayClicking with a mouse button displays the menu.
Clicking displays the pull-down menu. To close the menu,
click anywhere in the background.
Adjusting and Setting DisplayYou can select a menu item and click with a mouse button to
make adjustments and settings.
ExamplesClick (or press and hold) the mouse button orto adjust
the brightness. Or click and drag the mouse button on the slide
bar horizontally to adjust it.
To save the adjustments, click 
. This closes the menu. If you
click anywhere in the background while displaying an adjust-
ment and setting menu or dialog box, you will go to the main
menu after clicking with the mouse.
Clicking 
 displays help.
Using the Middle Button/Wheel on a Mouse (when avail-
able)
The projector supports the middle button/wheel on a mouse. With
the middle button/wheel you can use a scroll bar or click the middle
button/wheel to display or hide the Chalkboard toolbar.
b Using the USB HUB Function
When using the projector with a PC via the supplied USB cable, both the
USB port(type A) on the projector can be connected to a USB-supported
scanner or other USB-supported device. (USB Hub Function)
Example: When connecting a PC and a scanner to each USB port respec-
tively
An example of how a scanned image is projected
1. Install the Dynamic Image Utility on your PC.
NOTE: The Dynamic Image Utility is contained on the supplied CD-ROM. See“6-b Software Installation” for the installation procedure.
2. Use your scanner to scan an image.
NOTE: A scanner driver must be installed on your PC before use.
3. Load the scanned image on your PC using the Dynamic Image Utility.
4. Transmit the scanned image from your PC to the projector via the USB
cable and project the image on the screen.
NOTE:
• The USB HUB function is effective only when “Auto” is selected in Operation
Mode Select.
• The PCs using the USB Host Controller may not be available.
• When connecting a USB hub to the USB port (type B) on the projector, be sure
to use a USB hub capable of supplying 500mA per port of downstream current.
IN
USB (MOUSE/HUB)USB (PC)PC CARD2
1
PC CONTROL
IN OUT
OUT SC TRIGGER REMOTE 2REMOTE 1LAN
AC IN 
AUDIO
AUDIOAUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/HV
RL/MONO
RL/MONORL/MONOL/MONO
OPTION 1 OPTION 2DVI
RGB OUT
RGB 1
RGB 2
VIDEOS-VIDEO
USB(MOUSE/HUB)
4. Convenient Features
IN
USB (MOUSE/HUB)USB (PC)PC CARD2
1
PC CONTROL
IN OUT
OUT SC TRIGGER REMOTE 2REMOTE 1LAN
AC IN 
AUDIO
AUDIOAUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/HV
RL/MONO
RL/MONORL/MONOL/MONO
OPTION 1 OPTION 2DVI
RGB OUT
RGB 1
RGB 2
VIDEOS-VIDEO
USB(PC)
Operate the PC mouse using the USB mouse
NOTE: You can select the operation mode of the USB mouse connected to the USBport of the projector.
INUSB (MOUSE/HUB)USB (PC)PC CARD2
1
PC CONTROL
IN OUT
OUT SC TRIGGER REMOTE 2REMOTE 1LAN
AC IN 
AUDIO
AUDIOAUDIO OUTR
R/Cr
G/Y
B/Cb
V
H/HV
RL/MONO
RL/MONORL/MONOL/MONO
OPTION 1 OPTION 2DVI
RGB OUT
RGB 1RGB 2VIDEOS-VIDEO
USB(
PC)
USB(
MOUSE/HUB) 
						

							4-4
n Changing Background Logo
You can change the default background logo using the PC Card Files
feature.
NOTE: File size must be 256KB or less. File formats other than JPEG and BMP arenot available.
1. From the menu, select [Tools] 
→[PC Card Files] to display a list of all
the files stored in the PC card so that you can select a file you want to
use as a background logo.
2. The Logo button allows you to select a background logo from graphic
files on a PC card and change to it as the background logo.
3. Use the SELECT 

orbutton to select a JPEG or BMP file for your
background logo.
4. Use the SELECT 
 and then  button to select "Logo".
5. Press the ENTER button on the remote control or the cabinet. You
will get the confirmation dialog box.
6. Select "OK" and press the ENTER button. This completes changing
a logo for the background.
* Once you have changed the background from the NEC logo to an-
other, you cannot return the logo to background even by using Fac-
tory Default. To do so, repeat the above steps. The NEC logo file is
included on the supplied CD-ROM NEC Projector User Supportware
(“/Logo/nec_bb_x.jpg” for GT5000 and “/Logo/nec_bbsx.jpg” for
GT6000).
mMaking Freehand Drawings on a Projected
Image (ChalkBoard)
The ChalkBoard feature allows you to write and draw messages on a pro-
jected image.
NOTE: The ChalkBoard feature is available only when a USB mouse is used.
From the menu, select [Tools] → [ChalkBoard] to display the ChalkBoard
tool bar that contains the following icons.
NOTE: You can also display the ChalkBoard tool bar by clicking the scroll button onyour USB mouse.
PenEraser Drive
Exit
Clear Color
Pen .............. Left-click and drag to draw. Left-click [
] or right-click the
pen icon to display the pen palette containing four lines of
different thickness from which you can select a line you pre-
fer by left-clicking.
Color ........... Selects a color. Left-click to display the color palette from
which you can select a color you prefer by left-clicking.
Capture ....... Left click to capture and save freehand drawings in the PC
card. (GT5000 only)
Eraser ......... Left-click and drag to erase part of a drawing. Left-click [
]
or right-click the eraser icon to display the eraser palette
containing four eraser of different thickness from which you
can select an eraser you prefer by left-clicking.
Clear ...........Left-click to clear the drawing completely from the
ChalkBoard screen.
Drive ............ Switches between PC Card slot. (GT5000 only)
Hide ............. Hides the tool bar by left-clicking. Right-clicking anywhere
on the screen displays the ChalkBoard tool bar again.
Exit .............. Clears the complete drawing and exits the ChalkBoard.
NOTE:
• The menu is not available while you display the ChalkBoard screen.
• Switching slides clears a drawing completely.
CaptureHide
4. Convenient Features 
						

							4-5
This function serves to store the adjusted value when using the Shift, Focus, and
Zoom buttons of the projector or the remote control.
Reference memory:
Reference  Point ....... Adjusted settings are stored in memory as a reference com-
mon to all the input sources. If no setting is stored in Cus-
tom Point, the adjusted settings in Reference Point will be
applied.
Custom memory:
Custom Point ........... Adjusted settings are stored in memory for each input sig-
nal.
Usage Example
When you wish to display on a screen having a 4:3 aspect ratio an NTSC or other
4:3 aspect ratio signal and an SXGA or other 5:4 aspect ratio signal:
Perform shift, focus, and zoom adjustments to set the vertical screen size of the
vertically tall 5:4 aspect ratio signal to standard.
Both 4:3 apsect ratio signals and 5:4 aspect ratio signals can now be displayed.
Note that with these shift, focus, and zoom adjustments, the 4:3 aspect ratio signal
will become smaller on the screen.
To eliminate this size reduction, adjust the shift, focus and zoom to the optimum
condition for each of the 4:3 aspect ratio signal and the 5:4 aspect ratio signal.
Memory (storage) of each of these values will permit projection at an optimum con-
dition upon signal switching.
1. Perform Zoom, Focus and Lens Shift adjustments and store them in memory
using “Set Custom Point”.
Another way to store your adjustments is to use the CTL and INFO buttons on
the remote control.
2. When “Yes” is selected for “Use Point on Signal Change”, the adjustment is ap-
plied to the signal you switched.
3. Select “OK” and press the ENTER button for the change to take effect.
NOTE: The Lens Memory function is not available in Link mode.
NOTE:
* Settings for zoom and focus cannot be stored for the GT13ZL, GT24ZL and GT34ZL lens; settings for lens
shift, zoom and focus can be stored for the GT12ZLB, GT13ZLB, GT19ZLB, GT20ZL, GT34ZLB and GT48ZLB
lens.
* The Lens Memory function is not available for the GT06RLB and GT10RLB lens.
Picture Mute during Lens Shift?
To turn off the image and sound during lens shift, select "Yes".
NOTE: This option is only available when "Yes" is selected for "Use Point on Signal Change?".
, Lens Memory
4. Convenient Features 
						

							5-1
5
Using the Viewer
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
z Making the Most out of the Viewer Function ............. 5-2
x Operating the Viewer Function from the Projector
(playback) ................................................................. 5-3 
						

							5-2
P
C
C
O
N
T
R
O
L
I
N
I
N O
U
T
O
S
C
 
T
R
I
G
G
E
RR
E
M
O
T
E
2 R
E
M
O
T
E
1 L
A
N
U
S
B(MOUSE/HUB)U
S
B(P
C)P
C
C
A
R
D2
1
NOTE:
• To use the Viewer, first you need to create presentation materials on your PC
using the Dynamic Image Utility 2.0 contained on the supplied NEC Projector
User Supportware CD-ROM. For installation, see “6- 
bSoftware Installation”.
For creating presentation materials, see the Slide show function on the on-line
manual of the Dynamic Image Utility 2.0.
• Selecting Viewer sets the audio input for DVI input.
z Making the Most out of the Viewer Function
Features
You can view presentation data, capture (GT5000 only), and play
images on the projector. A PC card is used to view presentation
data prepared on the computer and to capture and play images
projected with the projector.
The Viewer feature allows you to view slides stored on a PC
memory card (referred to as PC card in this manual) on the pro-
jector. Even if no computer is available, presentations can be
conducted simply with the projector. This feature is convenient
for holding presentations at meetings and in offices, as well as
for playing images taken on digital cameras.
Easy to use
• Presentations can be started immediately simply by inserting a
PC card (not supplied)
• Easy slide switching
• Remote control operation
• Jumping to list of slides or any specific slide
High quality images
• High resolution up to 1024 x 768 dots
• 24-bit full color playback
• Viewing of digital camera images
Simple utility software (for computer)
• Dynamic Image Utility 2.0 operable on Windows 98/Me/XP/2000
• Slides can be created by capturing the currently displayed image
(GT5000 only)
• Control screen for displaying lists of slides and editing
* Microsoft, Windows and PowerPoint are registered trademarks of
Microsoft Corporation.
Removing the PC Card
Press the eject button slowly. The eject button card pops out a
little. Press the eject button slowly again. Grasp the edges of
the PC card and pull it out. Push and insert the eject button
fully until it stops.
Eject button
NOTE: Do not eject the PC card while its data is being accessed.
CAUTION: Make sure that the PC card or LAN card is removed
during Standby mode (NOT Idle mode)or with the main power
off.Failure to do so may cause damage to the data on your PC
card or LAN card,or may cause the projector to
malfunction.Should a malfunction occur, turn off the main power
and turn it back on.
Direction for Inserting the PC Card
The PC card has a top and bottom and must be inserted into the
PC card slot in a specific direction. It cannot be inserted back-
wards or upside-down. Attempting to force it into the slot in the
wrong direction may break the internal pin and damage the card
slot. Refer to the PC card's operating instructions for the proper
direction of insertion.
PC Card Type
The PC Card slot accepts PCMCIA Type II only.
NOTE: The projector does not support FAT32 or NTFS formatted flash memory
card or USB memory device.
Be sure to use a flash memory card or USB memory device formatted with the
FAT16 or FAT file system.
To format your flash memory card or USB memory device in your computer, refer
to the document or help file that comes with your Windows.
Inserting and Removing a PC Card
NOTE:
• Do not try to force the PC card into the slot.
PC CARD2
1
PC CONTROL
IN
IN OUT
OUT SC TRIGGER
REMOTE 2 REMOTE 1LAN
AC IN 
USB(MOUSE/HUB)USB(PC)PC CARD2
1
NOTE: When using two PC cards, do not insert both PC cards into the two PC card
slots simultaneously. Doing so may cause projector malfunction such as shutting
down. Each PC card must be inserted slowly one at a time.
Inserting the PC Card• Hold the PC card horizontally and inser t it slowly into PC card slot
1 or 2 with its top facing up.
5. Using the Viewer
PC card (not supplied) 
						

							5-3
xOperating the Viewer Function from the
Projector (playback)
This section describes the operation for showing slides of pre-
sentation documents created using the Viewer function with the
projector. It is also possible to make slides directly from the im-
ages projected with the projector.
Projecting slides (Viewer)
1. Insert a PC card into the PC card slot.
Insert the PC card so that the end with the insertion direction arrow on
the top goes in first.
* Press the eject button to eject the card.
2. Select the "Viewer" from the Source Select menu.
3. Project slides.
Checking "Show Folder List", means that selecting Viewer input
displays a list of the folders in the PC card and if "Auto Play" is
checked the projector automatically starts to play slides at the
first slide of the folder you have selected.
A tool bar will appear when you press the MENU button on the
remote control or the projector cabinet or clicking with the right
button of a mouse.
The tool bar includes the following buttons:
Prev .......... Returns to the previous slide or folder. Or this lets
you play slides back in reverse.
Next .......... Advances to the next slide or folder. Or this lets you
play slides back.
Play .......... Plays back automatically or manually depending on
the setting on Viewer Options of the menu. This al-
lows you to move on to the next slide when "Manual
Play" is selected.
Stop .......... This allows you to stop Auto Play while you are play-
ing back and to resume playing from the selected
slide or folder when "Auto Play" is selected.
Jump ........ Displays a list of slides while you are playing back.
Select ....... Displays a list of folders while you are playing back.
Drive ......... Switches between PC Card slot.
Setup ........ Displays the Viewer Options dialog box on Page 2 of
the Setup dialog box.
Delete ....... Deletes a captured slide(s) or all the captured slides
in the Capture - specific folder. (GT5000 only)
View ......... Hides the tool bar while you are playing back. Press-
ing the MENU button or clicking with the right button
of a mouse shows it again.
NOTE: If no memory card is inserted in the PC CARD slot, there is no signal, and a
black, blue or logo background is displayed, depending on the setting.
Playback is stopped when 
button on the cabinet is pressed in Auto Play mode.
Up to 12 indexes can be displayed on the list of folders. The folder in the right
bottom is always a folder exclusively for captured images, but is only displayed
when images have been captured. (GT5000 only)
When the tool bar is not displayed:
You can use the andbutton on the cabinet to select folders
or slides.
Folder
02 : 0001 / 0008Folder Folder Folder
Folder
Multi cursor (blue marks)
Current folder number
Current slide
numberNumber of all slides in folder
SlideSlide Slide Slide
Slide
SlideSlideSlide
02 : 0004 / 0008
Slide(Table) cursor
(green marks)
Folder
Use the SELECT orbutton to advance to the next folder
or return to the previous folder.
Use the SELECT orbutton to advance to the next slide or
return to the previous slide.
Prev Play Jump Drive
View
Next Stop SelectDelete
Setup
5. Using the Viewer
3D REFORM3D A
SELECT
STATUS LAMP 2 POWER
ON/STAND BY
AUTO ADJUST
MENU
ENTERCANCEL
3D REFORM3D
SELECT
STATUS LAMP 2 POWER
ON/STAND BY
MENU
ENTERCANCEL