NEC Ht1000 Entertainment Projector Users Manual

							HT1000
Entertainment Projector
User’s Manual 
						

							LIMITED WARRANTYExcept as specified below, the warranty that may be provided by the
dealer covers all defects in material or workmanship in this product.
The following are not covered by the warranty:
1. Any product on which the serial number has been defaced, modified
or removed.
2. Damage, deterioration or malfunction resulting from;
a. Accident, misuse, abuse, neglect, fire, water, dust, smoke, lightning or
other acts of nature, unauthorized product modification, or failure to fol-
low instructions supplied with the product.
b. Repair or attempted repair by non-authorized persons.
c. Any shipment of product (claim must be presented to the carrier).
d. Removal  or installation of the product.
e. Any other causes which do not relate to a product defect.
3. Cartons, carrying cases, batteries, external cabinets, CDROM, or
anyaccessories used in connection with the product.
4. Removal or installation charges.
5. Cost of initial technical adjustments (set-up), including adjustment
of user controls. These costs are the responsibility of the dealer from
whom the product was purchased.
6. Payment of shipping charges.
GARANTIE LIMITEEMis à part les point indiqués ci-dessous, la garantie pouvant être
couverte par le revendeur comporte l’ensemble des défauts se
rapportant au matériel ou aux travaux d’assemblage sur ce produit.
Les points suivants ne sont pas couverts par la garantie:
1. Les produits dont les numéro de série a été effacé, modifié ou retiré.
2. Dommages, dégâts ou dysfonctionnement suite à;
a. Un accident, mauvaise utilisation, abus, négligences, incendies, dégats
dûs aux eaux, à la poussière, à la fumée, aux éclairs ou autres phénomènes
naturels, à une modification non autorisée du produit, ou à la non-
conformité aux instructions fournies avec le produit.
b. Réparation ou tentative de réparation par des personnes non autorisées.
c. Toute expédition du produit (les plaintes doivent être adressées à la société
de frêt).
d. Démontage ou installation du produit.
e. Toute autre cause ne se rapportant pas à un défaut du produit.
3. Les cartons, boîtes, piles, caissons externes, CDROM, ou tout au-
tre accessoire utilisé avec ce poduit.
4. Prix de démontage ou d’installation.
5. Coût des réglages techniques de base (mise au point), incluant les
réglages des commandes utilisateurs. Ces coûts sont placés sous
la responsabilité du revendeur auprès duquel le produit a été acheté.
6. Paiement des frais de transport.
BESCHRÄNKTE GARANTIEAußer in den unten beschriebenen Fällen deckt die vom Händler unter
Umständen gewährte Garantie alle Material- oder Herstellungsfehler
dieses Produktes ab. In den folgenden Fällen wird keine Garantie
gewährt:
1. Wenn die Seriennummer des Produktes unleserlich gemacht,
geändert oder entfernt worden ist.
2. Bei einer Beschädigung, Beeinträchtigung oder Funktionsstörung,
die aus folgenden Fällen resultiert:
a. Unfall, falscher Gebrauch, Missbrauch, Fahrlässigkeit, Feuer, Wasser,
Staub, Rauch, Blitzeinschlag oder andere Naturereignisse, nicht
autorisierte Veränderungen des Produktes oder die Missachtung der dem
Produkt beigefügten Anleitung.
b. Reparatur oder der Versuch einer Reparatur durch nicht autorisierte
Personen.
c. Jeglicher Transport des Produktes (die Haftung liegt in diesem Fall bei
der den Transport durchführenden Person).
d. Entfernung oder Installation des Produktes.
e. Jegliche andere Ursachen, die nicht mit einem Defekt dieses Produktes
zusammenhängen.
3.
Verwendung von Kartons, Transportkisten, Batterien, Außengehäusen,CD-ROMs oder anderem Zubehör zusammen mit diesem Produkt.
4. Entfernungs- oder Installationsforderungen und –kosten.
5. Kosten der technischen Anfangseinstellungen (Setup), einschließlich
der Einstellungen der Benutzersteuerungen. Diese Kosten sind vom
Händler zu tragen, von dem das Produkt erworben wurde.
6. Bezahlung von Transportkosten.
GARANZIA LIMITATAA parte la specificazione seguente, la graanzia che potrebbe essere
fornita dal rivenditore copre tutti i difetti di materiali o nella lavorazione
in questo prodotto. I seguenti non sono coperti dalla garanzia :
1. Ogni prodotto che ha il numero seriale difettoso, modificato o rimosso.
2. Danni, deterioramento o malfunzionamento risultanti da;
a. Incidenti, abuso, cattivo uso, negligenza, fuoco, acqua, polvere, fumo,
fulmini o altri atti naturali di tipo naturale, modifiche inautorizzate del
prodotto, o errori nel seguire le istruzioni fornite con il prodotto.
b. Riparazioni o tentativi di riparazioni effettuati da persono non autorizzate.
c. Qualsiasi trasporto del prodotto (i reclami devono essere presentati dal
corriere).
d. Rimozione o installazione del prodotto.
e. ogni altra causa non relativa ad un deficit del prodotto.
3. Cartoni, scatole di trasporto, batterie, armadietti esterni, CDROM, o
qualsiasi altro accessorio annesso al prodotto.
4. Carichi di rimozione o installazione.
5. Costi di aggiustamenti tecnici iniziali  (set-up), includendo i comandi
di regolazione. Il rivenditore dal quale avete acquistato il prodotto è
responsabile di ciò.
6. Pagamento delle spese di consegna.
GARANTÍA LIMITADAA excepción de lo que se especifica abajo, la garantía que puede ser
suministrada por el distribuidor cubre todos los defectos en material o
elaboración en este producto. Lo siguiente no es cubierto por la garantía:
1. Cualquier producto en el cual el número serial haya sido desfigurado,
modificado o removido.
2. Daños, deterioro o malfuncionamiento resultado de;
a. Accidente, mal manejo, abuso, negligencia, fuego, agua, polvo, humo,
relámpagos u otros fenómenos naturales, modificaciones del producto
sin autorización, fallas en el seguimiento de las instrucciones
suministradas con el producto.
b. Reparación o intentos de reparación por personas no autorizadas.
c. Cualquier envío del producto (el reclamo debe presentarse al
transportador).
d. Remoción o instalación del producto.
e. Cualquier otra causa que no este relacionada con un defecto del producto.
3. Cartones, estuches de transporte, pilas, gabinetes externos,
CDROM, o cualquier accesorio utilizado en conexión con el producto.
4. Costos por instalación o remoción.
5. Costo de los ajustes técnicos iniciales (configuración), incluyendo
el ajuste de los controles de usuario. Estos costos son
responsabilidad del distribuidor donde se adquirió el producto.
6. Pago de los costos de envío.
BEGRÄNSAD GARANTIGarantin som ges av återförsäljaren täcker alla brister i material och
utförande med undantag av vad som anges nedan. Följande täcks inte
av garantin:
1. Produkter vars serienummer har blivit oläsligt, modifierats eller tagits
bort.
2. Skador, försämring eller felfunktion som beror på:
a. Olyckor, fel bruk, missbruk, vanskötsel, brand, vatten, rök, stoft, åska
eller annan orsak som beror på naturen, icke auktoriserad modifikation
av produkten samt underlåtenhet att följa anvisningarna som lämnas med
produkten.
b. Reparationer eller försök på reparation av icke auktoriserade personer.
c. Transportskador (dessa bör riktas till transportföretaget).
d. Avmontering eller installation av produkten.
e. Övriga orsaker som inte har något samband med produktens fel.
3. Förpackningslådor, bärväskor, batterier, externa höljen, CD-ROM-
skivor samt andra tillbehör som används tillsammans med produkten.
4. Avmonterings- och installationskostnader.
5. Kostnader för tekniska justeringar (inställning), inklusive justering
av användarreglagen. Dessa kostnader är återförsäljarens ansvar
där produkten köpts.
6. Betalning för transportkostnader. 
						

							NEC SOLUTIONS’ PROJECTOR PRODUCTSNEC Solutions (America), Inc. (hereafter NEC Solutions) warrants
this product to be free from defects in material and workmanship
under the following terms.
HOW LONG IS THE WARRANTYNEC Solutions’ HT1000 projector is covered by a two (2) year
limited parts and labor warranty from the date of the first cus-
tomer purchase. The lamp when used under normal operating
conditions is warranted for 1000 hours or six months, whichever
comes first.
WHO IS PROTECTEDThis warranty may be enforced only by the first purchaser, and is
not transferable.
WHAT IS COVERED AND WHAT IS NOT COVEREDExcept as specified below, this warranty covers all defects in
material or workmanship in this product.
NEC SOLUTIONS’ LIABILITY FOR ANY DEFECTIVE PRODUCT IS
LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT
AT NEC SOLUTIONS’ OPTION. REPLACEMENT PRODUCTS MAY
BE NEW OR ‘LIKE NEW’. The following are not covered by the
limited warranty and NEC Solutions shall not be liable for:
1. Any product which is not distributed in the U.S.A. or Canada
by NEC Solutions or which is not purchased, installed, and
operated in the U.S.A or Canada.
2. Any product on which the serial number has been defaced,
modified or removed.
3. Normal decrease in lamp light output over time.
4. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, abuse, neglect, improper ventilation, fire,
dust, smoke, water, lightning or other acts of nature, unau-
thorized product modification, or failure to follow instruc-
tions supplied with the product.
b. Repair or attempted repair by anyone other than a NEC
Solutions authorized service center.
c. Any shipment of the product (claims must be presented to
the carrier).
d. Removal or installation of the product.
e. Any other cause which does not relate to a product defect.
f. Use of the product beyond normal operating conditions.
Normal operating conditions are defined as product use
not in excess of 8 hours per day and 260 days per year.
5. Cartons, carrying cases, shipping cases, batteries, external
cabinets, magnetic tapes, or any accessories used in connec-
tion with the product.
6. Service required as a result of third party components.
WHAT NEC SOLUTIONS WILL PAY FORNEC Solutions will pay labor and material expenses for covered
items, but NEC Solutions will not pay for the following:
1. Removal or installation charges.
2. Costs of technical adjustments, set-up, maintenance, or adjust-
ment of user controls.
3. Payment of shipping and related charges incurred in returning
the product for warranty repair.
LIMITED WARRANTY (USA and Canada only)
HOW YOU CAN GET WARRANTY SERVICE1. To obtain service on your product, consult the dealer from whom
you purchased the product.
2.
Whenever warranty service is required, the original dated invoice
(or a copy) must be presented as proof of warranty coverage. In
order to obtain warranty service, you may be required to describe
and demonstrate the problem to your dealer or to NEC Solutions.
3. All products returned to NEC Solutions for service MUST have
prior approval. To receive approval or for the name of the
nearest NEC Solutions authorized service center, call NEC
Solutions at 800-836-0655.
4. It shall be your obligation and expense to ship the product,
freight prepaid, or to deliver it to a NEC Solutions authorized
service center, in either the original package or a similar pack-
age affording an equal degree of protection.
5.
In the event a product is returned to NEC Solutions for warranty
service, and it is determined that there is no product defect or that
the product condition is not covered by this limited warranty, a
diagnostic service fee may be charged to the customer.
LIMITATION OF IMPLIED WARRANTIESEXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY,
NEC SOLUTIONS MAKES NO OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. ANY IMPLIED WARRAN-
TIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS
AND DURATION OF THIS LIMITED WARRANTY.
EXCLUSION OF DAMAGESNEC SOLUTIONS’ LIABILITY FOR ANY DEFECTIVE PRODUCT IS
LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT
AT NEC SOLUTIONS’ OPTION. NEC SOLUTIONS SHALL NOT
BE LIABLE FOR:
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS
IN THIS PRODUCT, DAMAGES BASED UPON INCONVE-
NIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME,
COMMERCIAL LOSS; OR
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSE-
QUENTIAL OR OTHERWISE.
HOW STATE LAW RELATES TO THE WARRANTYSOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG
AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLU-
SIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
FOR MORE INFORMATION, CONTACT:
NEC SOLUTIONS (AMERICA), INC.
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
TELEPHONE 800-836-0655
www.necvisualsystems.com
Customers are cautioned that product performance is affected by
system configuration, software, the application, customer data,
and operator control, among other factors. While NEC Solutions’
products are considered to be compatible with many systems, the
specific functional implementation by the customers of the prod-
uct may vary. Therefore, the suitability of a product for a specific
purpose or application must be determined by the customer and
is not warranted by NEC Solutions.
Printed in Japan
7N8P1722 
						

							DECLARATION OF CONFORMITY
U.S. Responsible Party:
Address:
Tel. No.:NEC Solutions (America), Inc.
1250 N. Arlington Heights Road
Itasca, Illinois 60143
(630) 467-5000
Type of Product:
Equipment Classification:
Models:Projector
Class B Peripheral
HT1000
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules. 
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. 
(1) This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation. 
						

							HT1000
Entertainment Projector
User’s Manual
English
Deutsch
Français
Italiano
Español
Svenska 
						

							E-2
Safety Cautions
Precautions
Please read this manual carefully before using your NEC HT1000 Pro-
jector and keep the manual handy for future reference. Your serial num-
ber is located on the bottom of your projector. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power
outlet.
The power outlet socket should be installed as near to the
equipment as possible, and should be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SERVICE PER-
SONNEL.
This symbol warns the user that uninsulated voltage within the
unit may be sufficient to cause electrical shock. Therefore, it is
dangerous to make any kind of contact with any part inside of
the unit.
This symbol alerts the user that important information con-
cerning the operation and maintenance of this unit has been
provided.
The information should be read carefully to avoid problems.
WARNINGTO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTEN-
SION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS
CAN BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COM-
PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALI-
FIED NEC SERVICE PERSONNEL.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Acoustic Noise Information Ordinance -3. GSGV:
The sound pressure level is less than 70 dB (A) according to ISO 3744
or ISO 7779.
RF Interference
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified
by NEC Soluctions (America), Inc. in this manual. Failure to com-
ply with this government regulation could void your right to
operate this equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio / TV technician for
help.
In UK, a BS approved power cable with moulded plug has a Black (five
Amps) fuse installed for use with this equipment. If a power cable is not
supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector
and to prevent fire and shock. Please read them carefully and heed all
warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from
dust and moisture.
3. Do not place your projector in direct sunlight, near heaters or heat
radiating appliances.
4.Exposure to direct sunlight, smoke or steam can harm internal com-
ponents.
5. Handle your projector carefully. Dropping or jarring can damage in-
ternal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b.The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
c.In addition, the ceiling must be strong enough to support the
projector and the installation must be in accordance with any
local building codes.
d. Please consult your dealer for more information.
IMPORTANT INFORMATION 
						

							E-3
For Europe only
SCART adapter
(7N520018)
Fire and Shock Precautions
1.Ensure that there is sufficient ventilation and that vents are unob-
structed to prevent the build-up of heat inside your projector. Allow at
least 3 inches (10 cm) of space between your projector and a wall.
2. Prevent foreign objects such as paper clips and bits of paper from
falling into your projector.
Do not attempt to retrieve any objects that might fall into your projec-
tor. Do not insert any metal objects such as a wire or screwdriver
into your projector. If something should fall into your projector, dis-
connect it immediately and have the object removed by a qualified
NEC service personnel.
3. Do not place any liquids on top of your projector.
4. Do not look into the lens while the projector is on. Serious damage
to your eyes could result.
5.Keep any items such as magnifying glass out of the light path of the
projector. The light being projected from the lens is extensive, there-
fore any kind of abnormal objects that can redirect light coming out
of the lens, can cause unpredictable outcome such as fire or injury
to the eyes.
6. Do not cover the lens with the supplied lens cap or equivalent while
the projector is on. Doing so can lead to melting of the cap and
possibly burning your hands due to the heat emitted from the light
output.
7. The projector is designed to operate on a power supply of 100-120
or 200-240 V 50/60 Hz AC. Ensure that your power supply fits this
requirement before attempting to use your projector.
8.Handle the power cable carefully and avoid excessive bending.
A damaged cord can cause electric shock or fire.
9.If the projector is not to be used for an extended period of time,
disconnect the plug from the power outlet.
10. Do not touch the power plug during a thunderstorm. Doing so can
cause elecrical shock or fire.
CAUTION
1. Do not try to touch the ventilation outlet on the front and side as it
can become heated while the projector is turned on.
2.Do no use the tilt-foot for purposes other than originally intended.
Misuses such as gripping the tilt-foot or hanging on the wall can
cause damage to the projector.
3. Enable High-Speed Fan mode if you continue to use the projector
for consecutive days. (From the Advanced menu, select [Projector
Options] → [Setup] → [Page 4] → [High Speed Fan Mode].)
4.Do not unplug the power cable from the wall outlet under any one of
the following circumstances.
Doing so can cause damage to the projector:
*While the Hour Glass icon appears.
*While the message Please wait a moment. appears. This mes-
sage will be displayed after the projector is turned off.
*While the cooling fans are running. (The cooling fans continue to
work for 90 seconds after the projector is turned off).
5.Do not eject the PC card while its data is being accessed. Doing so
can damage your PC card data.
6.Do not hold the lens part with your fingers. Doing so could pinch
fingers or hands causing injury.
Lamp Replacement
•To replace the lamp, follow all instructions provided on page E-48.
•Be sure to replace the lamp when the message The lamp has
reached the end of its usable life. Please replace the lamp.
appears. If you continue to use the lamp after the lamp has reached
the end of its usable life, the lamp bulb may shatter, and pieces of
glass may be scattered in the lamp case. Do not touch them as the
pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replacement.
•Allow a minimum of 90 seconds to elapse after turning off the pro-
jector. Then turn off the main power switch, disconnect the power
cable and allow 60 minutes to cool the projector before replacing
the lamp.
Whats in the Box?Make sure your box contains everything listed. If any pieces are miss-
ing, contact your dealer.
Please save the original box and packing materials if you ever need to
ship your HT1000 Projector.
Lens cap
(24FT8661)
Remote control
(7N900371)
Power cable
(7N080204: North America)
(7N080003: G model)Projector
Soft carrying case
(24BS7111)OFF
VIDEOAUTO ADJ.COMPONENTRGB
DVI POWERONS-VIDEO
ASPECT3
D
 R
E
F
O
R
ME
F
F
E
C
T
O
RPICTU
REVOLUMEMAG
NIFYHELPVIEW
ER
PIC-MUT
ES
L
ID
EF
OLD
ER
SLIDEL
I
S
T
SELECT
FREE
ZEPO
SITIO
N
Batteries
S
E
L
E
C
TCNACELTERNEEMNUS
O
U
R
C
E
A
U
T
O
 
A
D
J
U
S
T
O
N S
T
A
N
D
 B
YSTATUS
POW
ER LAMP3
D
 
R
E
F
O
R
MP
C
-
C
A
R
D
RGB signal cable
(7N520001)
Audio cable
(7N520014)
S-Video cable
(7N520015)
Composite video cable
(7N520016)
Component video cable
(RCA
3-to-RCA
3)
(7N520017)
Quick
Connect
Guide
User’s 
manual
For North America only
Registration card
Limited warranty
For Europe only
Guarantee policy
String and rivet
(24C05051)     (24C04531) 
						

							E-4
TA B LE OF CONTENTS
IMPORTANT INFORMATION ........................................... E-2Safety Cautions ........................................................................................... E-2
Whats in the Box? ...................................................................................... E-3
INTRODUCTION ......................................................... E-5Introduction to the Projector ....................................................................... E-5
Part Names of the Projector ........................................................................ E-6
Attaching the lens cap .............................................................................. E-6
Top Features ............................................................................................. E-7
Terminal Panel Features ........................................................................... E-8
Part Names of the Remote Control ........................................................... E-9
Battery Installation .............................................................................. E-10
Remote Control Precautions ............................................................... E-10
Operating Range ................................................................................. E-10
INSTALLATION AND CONNECTIONS .................................. E-11Setting Up the Screen and the Projector ................................................... E-11
Selecting a Location ............................................................................... E-11
Throw Distance and Screen Size ............................................................ E-12
Making Connections .................................................................................. E-13
Wiring Diagram ...................................................................................... E-13
Connecting Your VCR or Laser Disc Player ............................................ E-14
Connecting Your DVD Player .................................................................. E-15
Connecting Your PC or Macintosh Computer ......................................... E-16
When Viewing a DVI Digital Signal ......................................................... E-17
Connecting the Supplied Power Cable .................................................... E-17
PROJECTING AN IMAGE (BASIC OPERATION) ...................... E-18Turning on the Projector ............................................................................ E-18
Selecting a Source ..................................................................................... E-19
Adjusting the Picture Size and Position ..................................................... E-19
Correcting the Horizontal and Vertical Keystone Distortion (3D Reform) .. E-20
Optimizing RGB Picture Automatically ...................................................... E-21
Turning Up or Down Volume ..................................................................... E-22
Turning off the Projector ........................................................................... E-22
CONVENIENT FEATURES .............................................. E-23Using Sweet Vision function ...................................................................... E-23
Using Zoom Position ................................................................................. E-23
Turning Off the Image and Sound .............................................................. E-24
Freezing a Picture ...................................................................................... E-24
Enlarging and Moving a Picture ................................................................. E-24
Getting the On-line Help ............................................................................ E-24
Changing Background Logo ...................................................................... E-25
USING THE VIEWER ................................................... E-26Making the Most out of the Viewer Function ............................................. E-26
Operating the Viewer Function from the Projector (playback) ................... E-27
Projecting slides (Viewer) ...................................................................... E-27
Auto Play Mode ...................................................................................... E-28
Switching to Slides Directly from Other Input Modes ............................ E-28
Viewing Digital Images ........................................................................... E-28
Storing Images Displayed on the Projector on the PC card (Capture) .... E-28
Deleting Captured Images ...................................................................... E-29
Using the PC Card Files Fucntion (PC Card Files) ................................... E-29
USING ON-SCREEN MENU ............................................ E-30Basic Menu Operation ............................................................................... E-30
Using the Menus .................................................................................... E-30
Customizing the Menu ........................................................................... E-30
Menu tree .................................................................................................. E-31
Menu Elements .......................................................................................... E-34
Entering Alphanumeric Characters by Using the Menu .......................... E-35
Menu Descriptions & Functions ................................................................ E-35
Source Select ......................................................................................... E-35
Video/S-Video/Component/RGB/DVI (DIGITAL)/Viewer/Entry List
Image Options ........................................................................................ E-36
Selecting Aspect Ratio ........................................................................ E-36
Masking Unwanted Area (Blanking) .................................................... E-38
Adjusting Position and Clock .............................................................. E-38
Zoom Position .................................................................................... E-38
Selecting Resolution ........................................................................... E-38
Selecting Overscan Percentage ........................................................... E-38
Selecting Video Filter Level ................................................................. E-38
Selecting Noise Reduction Level ......................................................... E-38
Selecting Signal Type .......................................................................... E-38Picture Management .............................................................................. E-38
Picture ................................................................................................ E-39
User Adjust (when using User 1 to 4) ................................................. E-39
Selecting Reference Setting .......................................................... E-39
Selecting Gamma Correction Mode .............................................. E-39
Selecting Color Correction ............................................................ E-39
Adjusting Color Temperature and White Balance .......................... E-39
Picture Options ............................................................................. E-39
Sweet Vision/3D Y/C Separation/Deinterlace/Black Expansion/Con-
trast Enhancement
Projector Options ................................................................................... E-40
Using 3D Reform ................................................................................ E-40
Keystone ....................................................................................... E-40
Cornerstone .................................................................................. E-40
Menu [Page1] ..................................................................................... E-40
Selecting Menu Language/Selecting Menu Mode/Customizing the
Menu/Selecting Menu Display Time
Menu [Page 2] .................................................................................... E-40
Turning On / Off Source Display / Turning On / Off Message / Selecting
Menu Color
Setup [Page 1] .................................................................................... E-41
Setting Lamp Mode to Normal or Eco/Selecting Projector Orientation/
Selecting a Color or Logo for Background
Setup [Page 2] .................................................................................... E-41
Setting Viewer Options/Selecting Capture Options
Setup [Page 3] .................................................................................... E-41
Selecting Signal Format
Setup [Page 4] .................................................................................... E-41
Enabling Auto Adjust/Enabling Auto Start/Enabling Power Manage-
ment/Enabling Power Off Confirmation/Enabling Horizontal and Verti-
cal Keystone Correction Save/Enabling High Speed Fan Mode/Enabling
Idle Mode/Enabling Screen Trigger/Enabling 3D Surround/Clearing
Lamp Hour Meter
Setup [Page 5] .................................................................................... E-42
Selecting Communication Speed/Selecting Default Source/Disabling the
Cabinet Buttons
Selecting Aspect Ratio and Position for Screen .................................. E-43
Setting LAN Mode ............................................................................... E-43
IP Address .................................................................................... E-43
Mail .............................................................................................. E-44
Status ........................................................................................... E-44
Setting a Password ............................................................................. E-45
Security ............................................................................................... E-45
Tools ...................................................................................................... E-47
Using Sleep Timer ............................................................................... E-47
Using Capture ..................................................................................... E-47
Using PC Card Files ............................................................................ E-47
Help ........................................................................................................ E-47
Contents ............................................................................................. E-47
Information ......................................................................................... E-47
Returning to Factory Default .................................................................. E-47
MAINTENANCE ........................................................ E-48Replacing the Lamp ................................................................................... E-48
Cleaning .................................................................................................... E-49
Lens Protector ....................................................................................... E-49
TROUBLESHOOTING ................................................... E-50Power Indicator ......................................................................................... E-50
Status Indicator ......................................................................................... E-50
Lamp Indicator .......................................................................................... E-50
Common Problems & Solutions ................................................................ E-51
When using the Viewer function ................................................................ E-51
SPECIFICATIONS ...................................................... E-52
APPENDIX .............................................................. E-53
Cabinet Dimensions .................................................................................. E-53
Pin Assignments of D-Sub RGB Input Connector ...................................... E-53
Compatible Input Signal List ..................................................................... E-54
Compatible Input Signal List for DVI Signal (RGB only) ............................ E-55
PC Control Codes and Cable Connection ................................................... E-56
PC Control Connector (DIN-8P) ................................................................ E-56
Using Software Keyboard .......................................................................... E-56
Operation Using an HTTP Browser ............................................................ E-57
TravelCare Guide ....................................................................................... E-58 
						

							E-5
INTRODUCTION
Introduction to the ProjectorThis section introduces you to your new HT1000 Projector and describes
the features and controls.
Congratulations on Your Purchase of The HT1000 Pro-
jector
The HT1000 is our most sophisticated single chip DLP™ based projec-
tor for the commercial and residential entertainment user. With the
HT1000 you will enjoy projecting images up to 200 (measured diago-
nally) from your DVD player, VCR, satellite hookup, HDTV source, PC
or Macintosh computer (desktop or notebook) and images from you
digital camera. The HT1000 can be setup on a coffee table, tabletop,
cart, bookshelf or permanently installed*
1. With an extensive input panel,
quick connect guide and full function remote, you will be ready to im-
merse yourself in big screen enjoyment.
Features you’ll enjoy on the HT1000:
•Phenomenal 3000:1 contrast ratio with a variable IRIS that allows
you to fine-tune the image contrast
•3D Reform technology for positioning the projector in off center loca-
tions in the room and still get aligned images
•NEC designed and developed SweetVision™ technology for en-
hanced images, more vibrant colors and blacks richer with detail
•Faroudja
® DCDi™ video processing technology
•Ability to display 16:9 and 4:3 aspect ratio sources
•HDTV, SDTV compatibility
•3D 10-bit video decoder for expanded black levels and adaptive
gamma correction
•Digital photo viewer to display larger than life images from your digi-
tal cameras PC or compact flash card
•Built in speakers with 3D sound for an integrated audio solution
•Easy set up and operation
•High performance long life lamp for low total operating costs
•Eco-mode lamp technology for increased lamp life and energy sav-
ings
•Uncompromising display of video and data. Improves white level, color
accuracy, dynamic range, and display of varying levels of black in an
image.
•Sealed optics for reduced maintenance and better performance in
dusty areas
•Wireless remote control operation
•Network capable with a wired card for the ability to maintain and
control your projector from your computer
•Smart security settings for password protection, control panel lock
and PC card protection key to help prevent unauthorized use
•Multiple video mode selections depending on your source.
•Control the unit with a PC using the PC Control port.
•NEC’s exclusive Advanced AccuBlend intelligent pixel blending tech-
nology - an extremely accurate image compression technology - of-
fers a crisp image with HTDV 1080p (1920
1080) resolution*
2.
•Supports most IBM VGA, SVGA, XGA, SXGA (with Advanced
AccuBlend)*
2, Macintosh, component signal (YCbCr/ YPbPr) or any
other RGB signals within a horizontal frequency range of 24 to 69 kHz
and a vertical frequency range of 48 to 88 Hz. This includes NTSC,
PAL, PAL-N, PAL-M, PAL60, SECAM and NTSC4.43 standard video
signals.
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in Western Europe.
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.
PAL-M: TV standard used in Brazil.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
•You can control the projector with a PC using the PC Control port
and wired LAN.
•The contemporary cabinet design is light, compact, easy to carry.
*
1Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
In addition, the ceiling must be strong enough to support the pro-
jector and the installation must be in accordance with any local
building codes. Please consult your dealer for more information.
*
2HDTV 1080p (1920
1080), HDTV 1080i (1920
1080) and
HDTV 720p (1280
720) are displayed with NEC’s Advanced
AccuBlend.
Digital Light Processing, DLP, Digital Micromirror Device and DMD are
trademarks of Texas Instruments.
The specifications are subject to change without notice.
Faroudja is a registered trademark of Faroudja Laboratories, Inc. DCDi
is a trademark of Faroudja Laboratories, Inc.
All other trademarks are the property of their respective owners.
All specifications subject to change without notice. 
						

							E-6
Part Names of the Projector
S
E
L
E
C
TCNACELTERNEEMNUS
O
U
R
C
E
A
U
T
O
 A
D
J
U
S
T
O
N S
T
A
N
D
 B
YSTATUS
POWER LAMP3
D
 
R
E
F
O
R
MPC-CARD
Ventilation (outlet)
Heated air is exhausted from here
*This security slot supports the MicroSaver® Security System. MicroSaver® is a registered trademark of Kensington Microware Inc. The logo is
trademarked and owned by Kensington Microware Inc.
Built-in Security Slot (  )*
Adjustable Tilt Foot Lever (See page E-19)
Attaching the lens cap
To attach the lens cap to the bottom with the supplied string and rivet:
Remote Sensor (See page E-10)Focus Ring (See page E-20)
Controls (See page E-7)
Ventilation (inlet)
Zoom Lever (See page E-20)
Carrying Handle
Lens CapLens
Adjustable Tilt Foot (See page E-19)
PC CONTROL
RGB INDVI-D IN SG TRIGGER
VIDEO IN
S-VIDEO INS
-V
ID
E
O S
-V
ID
E
OR
G
B
/D
V
I R
G
B
/D
V
I V
ID
E
O V
ID
E
O
A
U
D
IO
 IN A
U
D
IO
 INCOMPONENTY
C
b
/P
bC
r/P
r
Stereo Speaker (2W)
AC Input
Connect the supplied power cables three-pin plug here, and plug the
other end into an active wall outlet. (See page E-17)Main Power Switch
When you plug the supplied power cable into an active wall outlet and
turn on the Main Power switch, the POWER indicator turns orange and
the projector is in standby mode. (See page E-18)
Remote Sensor (See page E-10)
PC Card Slot
Rear Foot
Ventilation (outlet)
Heated air is exhausted from here
Lamp cover screw
Rear Foot
Rotate to make the projector level. (See page E-20)
PC Card Eject Button
1.Thread the string through the
hole on the lens cap and then
tie a knot in the string.2.Use the rivet to attach the
string to the bottom of the
projector.
Iris Lever (See page E-20)
Lamp cover (See page E-48)