NEC Neax 2400 Ipx Wireless System Manual

							CHAPTER 5 NDA-24301
Pag e 1 94
Revision 1.0
COMMANDS
*ANSDNAssignment of Number Sharing Data for Network Data Memory
APMDAssignment of Trunk Line Appearance Maximum Necessary Digit for DM
APMLLAssignment of PS Multiline Data for Local Data Memory
APMLNAssignment of PS Multiline Data for Network Data Memory
APSPAssignment of Trunk Line Appearance for DM
AZDLZT Program Download
AHLGAssignment of CFT Hot Line Group
AHLGLAssignment of CFT Hot Line Group for LDM
AHLGNAssignment of CFT Hot Line Group for NDM
*AT R FAssignment of Traffic Measurement Order
AZARLAssignment of ZT Area Information for Local Data Memory
AZARNAssignment of ZT Area Information for Network Data Memory
COCS1LControl of CS/ZT Status Read for Local Data Memory
COCS1NControl of CS/ZT Status Read for Network Data Memory
COCS2LChange of CS/ZT Operation Parameter for Local Data Memory
COCS2NChange of CS/ZT Operation Parameter for Network Data Memory
COCS3LControl of CS/ZT Reset for Local Data Memory
COCS3NControl of CS/ZT Reset for Network Data Memory
DLINDisplay of a List of Roaming PS
DPSNDisplay of PS Station Data
DRPSDisplay of Reverse Develop PS Data
DTFPDisplay of CS/ZT Peg Count Data
MBCSLMake Busy of CS/ZT for Local Data Memory
MBCSNMake Busy of CS/ZT for Network Data Memory
Table 5-1  List of Commands  (Continued)
COMMAND 
NAMEFULL COMMAND NAME
Note:
An asterisk (*) indicates the commands whose contents are given slight addition or amendment in the PCS
system. This manual only describes the parts revised from the previous ones. Additionally, for more detail,
refer to “Office Data Specification” or “System Operations and Maintenance Manual” for the PBX for
commands marked with an asterisk (*). 
						

							NDA-24301 CHAPTER 5
Page 195
Revision 1.0
COMMANDS
1. COMMAND DESCRIPTION AND DA T A   S H E E T   F O R   A S S I G N M E N T
This chapter explains assignment commands and their parameters for this system. The contents of each
assignment command description are illustrated in Figure 5-1.
Figure 5-1  Command Descriptions
Command name
The assigned data dump  into the designated file by the 
list up command shown here.Command name (full name)
The purpose of command and the related service
feature are explained here.
Peripheral notice necessary to create the office data
which may include the following:
The related command and parameters
The related service feature
MAT operation instructions 
The system hardware operation to be affect the data
The data storage node within the fusion network          
The required parameters, the applicable data range and
parameter descriptions are explained here.     
AFDD
List Up: LFDD
1. GENERAL
2. PRECAUTIONS
3.DATA ENTRY INSTRUCTIONS
DISP
DISPLAY MESSAGE ON LCD (DISP) FUNCTION KEY CODE (FKY)1-320
FKY FKYService name Service nameD efa ult display Defau lt d is pla y
Assignment of Function Display Data
This command is used to assign the characters of software key indication on a D      Series E.
When this command is not assigned, the default(which shows on FKY parameter description on this command)
are displayed.
The LCD is 24 digits wide, and there are four of software keys, hence a maximum of 6 characters can be assigned
for each software key indication.
Displayed characters (Max. 6 characters of alphabet and numbers)
1FWD-BY
FKY(1-320) Note:The default displayed characters are shown in the parenthesis
1
2
3
4
5
6
7Call Forwarding-Busy Line
Call Forwarding-All Calls
Executive Right of Way
Call Waiting
CAll Back
-
Save  and Repe atFDB
FDA
BV
CW
CB
-
S&R
-60
61-82
83
84
85
86
87Manual Signaling Key
-
Retain Conference
Serial Call
Internal Zone Paging (Not released
for U.S.A.  an d Ca na da)
-
W ake  Up SetSIG
-
KEEP
S_CAL
IZP
-
WUS
term 
						

							CHAPTER 5 NDA-24301
Pag e 1 96
Revision 1.0
ACSDL  : Assignment of CS/ZT Data for Local Data Memory
1. GENERAL
This command is used to assign, delete, and display the CS/ZT-related data. A CSINT circuit card can
accommodate four CSs/ZTs, allowing each two groups of the Levels 0 and 4 to be assigned for one circuit card.
List Up Command: LCSDL
2. PRECAUTIONS
1. This command is used for the Local Node.
2. When assigning LENS, CS/ZT should be assigned in the Group of less than 24 and the Levels to be available
are 0 and 4.
3. While the CS/ZT is busy, the data cannot be deleted.
3. DATA ENTRY INSTRUCTIONS
PCN
GRNEnter the PCN (PHS Community Number)
Note: Group NO. available for inter-node
          of the Fusion Network
Enter the GRN (Group
Number)TN
Enter the TN (Tenant Number)
ERN
Enter the ERN (Calling 
Area Number)CSN / ZTN
Enter the CS / ZT number
1 = V1CS (Not used)
2 = V2CS (Not used)
3 = ZT1
4 = ZT2KIND
PHS
COMMUNITY
NUMBER
(PCN )
1 - 1024CALLING AREA
NUMBER
 (ERN )
1 - 32GROUP
NUMBER
 (GRN )
1 - 8TENANT
NUMBER
(TN )
1 - SYSTEM MAXEQUIPMENT
NUMBER
(LENS ) CS / ZT  NUMBER
 (CSN / ZTN )
1 - 32CS / ZT  KIND
 (KIND )
1 - 4 
						

							NDA-24301 CHAPTER 5
Page 197
Revision 1.0
4. DATA SHEET
CS/ZT Data Assignment Sheet
PHS 
COMMUNITY 
NUMBER
(PCN)
1-1024CALLING 
AREA NO.
(ERN)
1-32GROUP 
NO.
(GRN)
1-8CS/ZT 
NO.
(CSN/
ZTN)
1-32TENANT 
NUMBER
(TN)
1-
SYSTEM 
MAXLENS
CS/ZT 
KIND
(KIND)
3, 4 MG 
00-07U
0-3G
00-23LV  
0/4 
						

							CHAPTER 5 NDA-24301
Pag e 1 98
Revision 1.0
ACSDN  : Assignment of CS/ZT Data for Network Data Memory
1. GENERAL
This command is used to assign, delete and display the CS/ZT-related data of the Network Control Node (NCN).
A CSINT circuit card can accommodate four CSs/ZTs, allowing each two groups of the Levels 0 and 4 to be
assigned for one circuit card.
List Up Command: LCSDN
2. PRECAUTIONS
1. This command is used for the Network Control Node.
2. When assigning LENS, CS/ZT should be assigned in the Group of less than 24 and the Levels to be available
are 0 and 4.
3. The same ERN cannot be assigned to multiple nodes.
4. When you want to move ERN from A node to B node, you must delete each CS/ZT in the ERN of A node.
5. When assigning/deleting the CS/ZT-related data of the NCN, you must back up the Office data of the NCN
and the LN that mounts the CS. 
						

							NDA-24301 CHAPTER 5
Page 199
Revision 1.0
3. DATA ENTRY INSTRUCTIONS
PCN
GRN
Enter the PCN (PHS Community Number)
Note: Group NO. available for inter-node
           of the Fusion Network
Enter the GRN (Group 
Number)TN
Enter the TN (Tenant Number)
PHS
COMMUNITY
NUMBER
 ( PCN )
1 - 1024FUSION
POINT CODE
( FPC )
1 - 253CALLING 
AREA
NUMBER
 ( ERN )
1 - 32GROUP
NUMBER
 ( GRN )
1 - 8TENANT
NUMBER
( TN )
1-SYSTEM MAX
EQUIPMENT
NUMBER
( LENS ) CS / ZT  
NUMBER
 ( CSN / ZTN )
1 - 32CS / ZT  KIND
 ( KIND )
1 - 4
FPC
Enter the FPC in the
 Fusion NetworkERN
Enter the ERN (Calling 
Area Number)CSN / ZTN
Enter the CS / ZT number
1 = V1CS (Not used)
2 = V2CS (Not used)
3 = ZT1
4 = ZT2KIND 
						

							CHAPTER 5 NDA-24301
Pag e 2 00
Revision 1.0
4. DATA SHEET
CS/ZT Data Assignment Sheet
PHS 
COMMUNITY
NUMBER
(PCN)
1-1024FUSION
POINT CODE
(FPC)
1-253CALLING 
AREA 
NO.
(ERN)
1-32GROU
P NO.
(GRN)
1-8CS/
ZT 
NO.
(CSN
/
ZTN)
1-32TENANT 
NUMBER
(TN)
1-
SYSTEM 
MAXLENS
CS/
ZT
KIND
(KIND)
3, 4 MG 
00-07U
0-3G
00-23LV
0/4 
						

							NDA-24301 CHAPTER 5
Page 201
Revision 1.0
ACSEL  : Assignment of Expansion CS/ZT System Data for Local Data Memory
1. GENERAL
This command is used to assign, delete and display the expansion CS/ZT System data in Local Node.
List Up Command : LCSEL
2. PRECAUTIONS
1. This command is used to the Local Node.
2. Enter “0” when you make the corresponding parameter invalid (NWNO., ADERA, CTRN).
3. This command can be used to change the data.
3. DATA ENTRY INSTRUCTIONS
 
PCN
ADERAEnter the PCN (PHS Community
 Number)
Note: Group NO. available for
 inter-node of the Fusion
 NetworkADERA. is Maximum 2 digits.
00 : Additional Area Number is Not Exist
1 - FF : Additional Area Number is ExistNPCD
0 : PHS - Manager Code is Not Exist
1 : PHS - Manager Code - A is Exist
2 : PHS - Manager Code - A, B is Exist
3 : PHS - Manager Code - A, B, C is 
     Exist
4 : PHS - Manager Code - A, B, C, D is
     Exist
Note:  Fixed to 0
CTRN
CTRN is Maximum 4 digits.
0000 : Country Number is Not Exist
0001 - FFFF : Country Number is  Exist
  PHS COMMUNITY
NUMBER 
( PCN )
1 - 1024NETWORK
NUMBER
 ( NWNO. )
MAXIMUM 4 DIGITSADDITIONAL AREA
NUMBER
 ( ADERA )
MAXIMUM 2 DIGITSCOUNTRY
NUMBER
 ( CTRN )
MAXIMUM 4 DIGITSNUMBER OF PHS - 
MANAGER CODE
 ( NPCD )
0 - 4
NWNO.
NWNO. is Maximum 4 digits.
0000: Network Number is Not Exist
0001 - FFFF: Network Number is  Exist
  
						

							CHAPTER 5 NDA-24301
Pag e 2 02
Revision 1.0
4. DATA SHEET
Expansion CS/ZT System Data Assignment Sheet
PHS COMMUNITY 
NUMBER
(PCN)
1-1024NETWORK NO.
(NWNO.) 
0001-FFFFADD AREA
(ADERA) 
01-FFCOUNTRY NO. 
(CTRN)NUMBER OF
PHS-MANAGER CODE 
(NPCD)
0-4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 
						

							NDA-24301 CHAPTER 5
Page 203
Revision 1.0
ACSEN  : Assignment of Expansion CS/ZT System Data for Network Data Memory
1. GENERAL
This commands is used to assign, delete, and display the expansion CS/ZT System data in Network Data
Memory.
2. PRECAUTIONS
1. This Command is used for the Network Control Node.
2.  Enter “0” when you make the corresponding parameter invalid (NWNO, ADERA, CTRN).
3. This command can be used to change the data.
3. DATA ENTRY INSTRUCTIONS
PCN
ADERAEnter the PCN (PHS Community
Number)
Note: Group NO. available for
inter-node of the Fusion
NetworkADERA Has a Maximum of 2 digits.
00 : Additional Area Number Does 
1 - FF : Additional Area Number ExistsNPCD
0 : PHS - Manager Code Does Not Exist
1 : PHS - Manager Code - A Exists
2 : PHS - Manager Code - A, B Exists
3 : PHS - Manager Code - A, B, C  
     Exists
4 : PHS - Manager Code - A, B, C, D 
     Exists
Note:   Fixed to 0
CTRN
CTRN has a Maximum of 4 digits.
0000 : Country Number Does Not Exist
0001 - FFFF : Country Number Exists
  PHS COMMUNITY
NUMBER 
( PCN )
1 - 1024NETWORK
NUMBER
 ( NWNO )
MAXIMUM 4 DIGITSADDITIONAL AREA
NUMBER
 ( ADERA )
MAXIMUM 2 DIGITSCOUNTRY
NUMBER
 ( CTRN )
MAXIMUM 4 DIGITSNUMBER OF PHS - 
MANAGER CODE
 ( NPCD )
0 - 4
NWNO.
NWNO has a Maximum of 4 digits.
0000: Network Number Does Not Exist
0001 - FFFF: Network Number Exists
 
Not Exist