NEC Neax 2400 Ipx Wireless System Manual

							CHAPTER 5 NDA-24301
Pag e 2 94
Revision 1.0
2. COMMANDS FOR OPERATION AND MAINTENANCE
[Contents of Command Description]
Each command is explained dividing into the following parts.
 Command Name
Explained here are the command names to be entered via the keyboard and its full command names.
 General
General functions of each command are explained.
 Precaution
Cautions to be made when using each command are explained.
 Parameters
Parameters (data) assigned by each command are shown.
 How to Use
Usage of each command is explained.
 Related Commands
Related commands are shown. 
						

							NDA-24301 CHAPTER 5
Page 295
Revision 1.0
ATRF  : Assignment of Traffic Measurement Order
1. GENERAL
This command is used to assign and delete traffic measurement programs. A request for traffic measurement is
performed when a traffic measurement instruction has been assigned by this command. The collected traffic
measurement data can be output from the MAT printer or stored on the HD of the MAT, which can be designated
on the basis of traffic measurement type.
2. PRECAUTIONS
None
3. PARAMETERS
Input Data
TYPE : Type of Traffic Measurement (1-16)
Note:Refer to the “Operation & Maintenance Manual” for information about this data.
PORT : Traffic Information Output Terminal Number (0-7)
INTERVAL : Output interval (0-120)
Interval must be assigned in 10 minute increments or 0 can be assigned
which will require that an output time is assigned to “OUTPUT HOUR/
MINUTE”.
START HOUR
START MINUTE
END HOUR
END MINUTE
OUTPUT HOUR :This data is valid only when “INTERVAL” = 0.
OUTPUT MINUTE :This data is valid only when “INTERVAL” = 0.
SRT : Start External Route Number
ERT : End External Route Number
DATA MEANING DATA MEANING
1~16Note 17 ZT peg count 
						

							CHAPTER 5 NDA-24301
Pag e 2 96
Revision 1.0
AZARL  : Assignment of ZT Area Information for Local Data Memory
1. GENERAL
This command is used to assign and delete the Zone Transceiver Area information in the Local Node (LN).
2. PRECAUTIONS
1. This command is used for the Local Node.
2. All PSs data must be re-download, if control carrier data is changed via this command.
3. The parameters, WTZNSL, WTZNKL, RCHOOL, RCHOSL, RCHFE, CCHGFE, should not be changed
from default setting.
4. ZT must be restarted after using this command.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ZSL (ZONE SELECT LEVEL) : 0-255
ZKL (ZONE KEEP LEVEL) : 0-255
HOL (HAND-OVER OPERATION LEVEL) : 0-255
HSL (HAND-OVER SELECT LEVEL) : 0-255
HFT (HAND-OVER FOR THRESHOLD) : 0-255
CCFT (CHANNEL CHANGE FOR THRESHOLD) : 0-255
NCCR (NUMBER OF CONTROL CARRIER) : 0-5
CCR 1-5 (CONTROL CARRIER 1-5) : 0-20
If this is not assigned, the default setting is below.
ZSL = 67 (33dB µ V)
ZKL = 56 (22dB µ V)
HOL = 59 (25dB µ V)
HSL = 67 (33dB µ V)
HFT = 10 frame error/240 frame (1.2 sec)
(This is effective for mode2 ZT.)
CCFT = 24 frame error/240 frame (1.2 sec)
NCCR = 3
CCR 1 = 2 Channel
CCR 2 = 4 Channel
CCR 3 = 6 Channel
CCR 4 = 0 None
CCR 5 = 0 None 
						

							NDA-24301 CHAPTER 5
Page 297
Revision 1.0
AZARN  : Assignment of ZT Area Information for Network Data Memory
1. GENERAL
This command is used to assign and delete the Zone Transceiver Area information in the Network Control Node
(NCN).
2. PRECAUTIONS
1. This command is used for the Network Control Node.
2. All PSs data must be re-download, if control carrier data is changed via this command.
3. The parameters, WTZNSL, WTZNKL, RCHOOL, RCHOSL, RCHFE, CCHGFE, should not be changed
from default setting.
4. ZT must be restarted after using this command.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ZSL (ZONE SELECT LEVEL) : 0-255
ZKL (ZONE KEEP LEVEL) : 0-255
HOL (HAND-OVER OPERATION LEVEL) : 0-255
HSL (HAND-OVER SELECT LEVEL) : 0-255
HFT (HAND-OVER FOR THRESHOLD) : 0-255
CCFT (CHANNEL CHANGE FOR THRESHOLD) : 0-255
NCCR (NUMBER OF CONTROL CARRIER) : 0-5
CCR 1-5 (CONTROL CARRIER 1-5) : 0-20
If this data is not assigned, the default setting is below.
ZSL = 67 (33dB µ V)
ZKL = 56 (22dB µ V)
HOL = 59 (25dB µ V)
HSL = 67 (33dB µ V)
HFT = 10 frame error/240 frame (1.2 sec)
(This is effective for mode 2 ZT.)
CCFT = 24 frame error/240 frame (1.2 sec)
NCCR = 3
CCR 1 = 2 Channel
CCR 2 = 4 Channel
CCR 3 = 6 Channel
CCR 4 = 0 None
CCR 5 = 0 None 
						

							CHAPTER 5 NDA-24301
Pag e 2 98
Revision 1.0
COCS1L  : Control of CS/ZT Status Read for Local Data Memory
1. GENERAL
This command is used to read the status of the CS/ZT in the Local Node (LN).
2. PRECAUTIONS
This command is used for the Local Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
GRN (GROUP NUMBER) : 1-8
CSN (CS/ZT NUMBER) : 1-32
After the assignment data is processed between PBX and MAT; following parameter is automatically
assigned
LENS (EQUIPMENT NUMBER) : Line Equipment Number
TN (TENANT NUMBER) : 1-6
CS-ID (CS/ZT-IDENTIFY) : CS/ZT-Identify
MAIN (MAIN CONDITION OF CS/ZT : Main Condition of CS/ZT Management
MANAGEMENT FOR DEVICE SIDE) For Device Side
SUB (CONTROL CONDITION OF CS/ZT : Control Condition of CS/ZT Management
MANAGEMENT FOR DEVICE SIDE) For Device Side
CS/ZT TYPE (CS TYPE) : Control (Control CS/ZT)
General (Control CS/ZT)
CS STATUS (CS/ZT STATUS) : CS/ZT status (If parameter can be changed)
NON-OP (Non Open)
CLOSE (Close)
OPERATE (Operating Now)
LINK STATUS (DATA LINK STATUS) : Data Link Status (If parameter can be changed)
UNLINK (Data Link Break)
OPEN (Data Link Open)
CLOSE (CS/ZT Fault After Return)
FAULT (CS/ZT Fault)
BCH B2 (B2CH STATUS) : B2ch Status (If parameter can be changed)
IDLE (B2ch Idle)
BUSY (B2ch Busy)
CLOSE (B2ch Close)
BCH B3 (B4CH STATUS) : B3ch Status (If parameter can be changed)
IDLE (B3ch Idle)
BUSY (B3ch Busy)
CLOSE (B3ch Close)
BCH B4 (B4CH STATUS) : B4ch Status (If parameter can be changed)
IDLE (B4ch Idle)
BUSY (B4ch Busy)
CLOSE (B4ch Close)
FLT (NG CAUSE) : 0-FF (Only Display)
Only
Display 
						

							NDA-24301 CHAPTER 5
Page 299
Revision 1.0
COCS1N  : Control of CS/ZT Status Read for Network Data Memory
1. GENERAL
This command is used to read the status of the CS/ZT status read in the Network Control Node (NCN).
2. PRECAUTIONS
This command is used for the Network Control Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
GRN (GROUP NUMBER) : 1-8
CSN (CS/ZT NUMBER) : 1-32
After the assignment data is processed between PBX and MAT; following parameter is automatically
assigned
LENS (EQUIPMENT NUMBER) : Line Equipment Number
TN (TENANT NUMBER) : 1-6
CS-ID (CS/ZT-IDENTIFY) : CS/ZT-Identify
MAIN (MAIN CONDITION OF CS/ZT : Main Condition of CS/ZT Management
MANAGEMENT FOR DEVICE SIDE) For Device Side
SUB (CONTROL CONDITION OF CS/ZT : Control Condition of CS/ZT Management
MANAGEMENT FOR DEVICE SIDE) For Device Side
CS/ZT TYPE (CS TYPE) : Control (Control CS/ZT)
General (Control CS/ZT)
CS STATUS (CS/ZT STATUS) : CS/ZT status (If parameter can be changed)
NON-OP (Non Open)
CLOSE (Close)
OPERATE (Operating Now)
LINK STATUS (DATA LINK STATUS) : Data Link Status (If parameter can be changed)
UNLINK (Data Link Break)
OPEN (Data Link Open)
CLOSE (CS/ZT Fault After Return)
FAULT (CS/ZT Fault)
BCH B2 (B2CH STATUS) : B2ch Status (If parameter can be changed)
IDLE (B2ch Idle)
BUSY (B2ch Busy)
CLOSE (B2ch Close)
BCH B3 (B4CH STATUS) : B3ch Status (If parameter can be changed)
IDLE (B3ch Idle)
BUSY (B3ch Busy)
CLOSE (B3ch Close)
BCH B4 (B4CH STATUS) : B4ch Status (If parameter can be changed)
IDLE (B4ch Idle)
BUSY (B4ch Busy)
CLOSE (B4ch Close)
FLT (NG CAUSE) : 0-FF (Only Display)
Only
Display 
						

							CHAPTER 5 NDA-24301
Pag e 3 00
Revision 1.0
COCS2L  : Change of CS/ZT Operation Parameter for Local Data Memory
1. GENERAL
This command is used to change the CS/ZT operation parameter in the Local Node (LN).
2. PRECAUTIONS
This command is used for the Local Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
MODE (GLOBAL DEFINITION : 1: NOR (Normal)
INFORMATION PATTERN NUMBER) 2: HBY (Heavy)
ZONE (ZONE KIND) : 1: LG (Large)
2: SM (Small)
PAS (POSITION ASSIGNMENT) : 1: SET
2: CANCEL 
						

							NDA-24301 CHAPTER 5
Page 301
Revision 1.0
COCS2N  : Change of CS/ZT Operation Parameter for Network Data Memory
1. GENERAL
This command is used to change the CS/ZT operation parameter in the Network Control Node (NCN).
2. PRECAUTIONS
This command is used for the Network Data Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
MODE (GLOBAL DEFINITION : 1: NOR (Normal)
INFORMATION PATTERN NUMBER) 2: HBY (Heavy)
ZONE (ZONE KIND) : 1: LG (Large)
2: SM (Small)
PAS (POSITION ASSIGNMENT) : 1: SET
2: CANCEL 
						

							CHAPTER 5 NDA-24301
Pag e 3 02
Revision 1.0
COCS3L  : Change of CS/ZT Reset for Local Data Memory
1. GENERAL
This command is used to control CS/ZT Reset for the Local Node (LN).
2. PRECAUTIONS
This command is used for the Local Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
GRN (GROUP NUMBER) : 1-8
CSN (CS/ZT NUMBER) : 1-32
  After the assignment data is processed between PBX and MAT; following parameter is automatically
assigned
TN (TENANT NUMBER) : 1-System Max.
LENS (EQUIPMENT NUMBER) : LENS EQUIPMENT NUMBER
FLT (NG CAUSE) : 0-FF (Only Display) 
						

							NDA-24301 CHAPTER 5
Page 303
Revision 1.0
COCS3N  : Control of CS/ZT Reset for Network Data Memory
1. GENERAL
This command is used to control CS/ZT Reset for the Local Node (LN).
2. PRECAUTIONS
This command is used for the Network Control Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
GRN (GROUP NUMBER) : 1-8
CSN (CS/ZT NUMBER) : 1-32
 After the assignment data is processed between PBX and MAT; following parameters are automatically
assigned
TN (TENANT NUMBER) : 1-System Max.
LENS (EQUIPMENT NUMBER) : LENS EQUIPMENT NUMBER
FLT (NG CAUSE) : 0-FF (Only Display)