Netgear 5port Gigabit Ethernet Switch Manual

							Installation GuideGigabit Ethernet Switch
10/100/1000 Mbps 
GS605 / GS608 
						

							Unpack the Box and Verify the Contents
When you open the box, verify that you received everything. The package includes:
•5/8-port Gigabit Ethernet Switch GS605/GS608
•Power adapter
•Vertical stand
•Installation guide
•Warranty/Support information card
Prepare to Install the Switch
Decide where you want to place the switch. Find a flat horizontal surface — such as a table,
desk or shelf.
Make sure the selected location is:
•  Not in direct sunlight or near a heater or heating vent.
•  Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all
sides of the switch.
2
Introduction
The NETGEAR®5/8-Port Gigabit Ethernet Switch Model GS605 / GS608 provides you with
a high-speed, reliable, easy-to-use switch to connect up to five or eight different Ethernet
enabled devices (such as computers, file servers, print servers, printers, routers and hubs).
You use the GS605 / GS608 switch to build a small network that enables you to have 10
Mbps, 100 Mbps and 1000 Mbps connections to other devices on the network.  Using Gigabit
Ethernet (1000 Mbps), you will be sending files across your network at speeds up to 2,000
Mbps due to the full-dulpex nature of Gigabit Ethernet.  This enables you to move large
amounts of data up to 10 times faster than a Fast Ethernet switch.  Also, with this switch, you
can add extra computers to your cable or DSL router. 
Ethernet cables come as either straight-through or crossover cables—depending on whether
you’re connecting to a device (computer, server, or printer) or networking equipment (hub,
switch, or router). With the Auto Uplink™ feature, you don’t have to worry about which one
you use. Each port on the GS605/GS608 switch automatically configures itself correctly when
you plug in a device’s cable.
Installation Overview
Estimated Time: 5–10 minutes
1.  Unpack the box and verify the contents.
2.  Prepare to install the switch.
3.  Install the switch and connect the other devices.
1
Installation guide, Warranty/
Support information card
Power adapter Gigabit Ethernet Switch GS605/GS608 Vertical stand 
Gigabit Ethernet Switch GS605 / GS608
1  1 
2  2  
						

							Note:If you have more than 5 or 8 devices to connect to this switch, you must connect
them to a hub or other switch and then connect that hub or switch to this switch. See the
note about placing several switches near each other in section 2.
3.  Connect the power adapter’s cord into the back of the switch and then plug the adapter
into a power source (such as a wall socket or power strip).
The Power light should light up.
The corresponding port number for each connected and powered device should light when
link (connection), and flash when activity occurs.
Troubleshooting
The Power light is not lit
The switch has no power.
•Make sure the power cord is properly connected to the switch.
•Make sure the power adapter is properly connected to a functioning power outlet. If it’s in
a power strip, make sure the power strip is turned on. If the socket is controlled by a light
switch, make sure the switch is in the on position.
•Make sure you are using the NETGEAR power adapter supplied with your switch.
The Port number light is not lit for a connected device or
stays on continuously
There’s a hardware connection problem.
•Make sure the cable connectors are securely plugged in at the switch and the device.
•Make sure the connected device is turned on.
•If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card
or adapter is installed correctly and is working.
•Make sure the cable is less than 328 feet (100 meters). •  Well ventilated (especially if it is in a closet).
Note: Neither the GS605 nor GS608 are designed to be stacked on top of other GS605 or
GS608 switches. If you need several units in one location, use the vertical stand to position
several units near each other.
Also, you’ll need one Enhanced Category 5 (Cat 5e) Ethernet cable with RJ-45 connectors for
each device you want to connect to the switch. Each Ethernet cable must be less than 328 feet
(100 meters).
Install the Switch and Connect the
Other Devices
1. Place the switch on a flat surface.
2.  For each device, insert one end of an Ethernet cable into the port in the device and insert
the other end into one of the Ethernet ports on the switch.
43
Broadband
modem
Apple G4 PC with GA311 
Gigabit PCI AdapterPC with
FA 311 PCI
Adapter
GS608 8-port Gigabit Ethernet Switch
WGT624 108 Mbps WIreless Firewall Router
3  3  
						

							Statement of ConditionsIn the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the product described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Certificate of the Manufacturer/ImporterIt is hereby certified that the NETGEAR Model GS605/608 Gigabit Ethernet Switch has been suppressed in
accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some
equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain
restrictions. Please refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and
has been granted the right to test the series for compliance with the regulations.
Federal Communications Commission (FCC) Compliance Notice: Radio 
Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
•  This device may not cause harmful interference.
•  This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.
EN 55 022 Declaration of ConformanceThis is to certify that the NETGEAR Model GS605/608 Gigabit Ethernet Switch is shielded against the generation of
radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a.
Conformity is declared by the application of EN 55 022 Class A (CISPR 22).
Canadian Department of Communications Radio Interference RegulationsThis digital apparatus (NETGEAR Model GS605/608 Gigabit Ethernet Switch) does not exceed the Class A limits for
radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian
Department of CommunicationsRèglement sur le brouillage radioélectrique du ministère des Communications Cet appareil numérique (NETGEAR
Model GS605/608 Gigabit Ethernet Switch) respecte les limites de bruits radioélectriques visant les appareils
numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications
du Canada.
6
Technical Specification
Standards Compatibility:Specifications IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u, 
100BASE-TX Fast Ethernet, IEEE 802.3ab 1000BASE-T
Gigabit Ethernet, IEEE 802.3x Flow Control, IEEE 802.1p 
Priority Tags; compatible with Windows
®, Mac®OS, 
NetWare®, Linux®
Network Interface:RJ-45 connector for 10BASE-T, 100BASE-TX, or 1000BASE-T
Ethernet interface
DC Power:12W max and 12 V @ 1A DC input
Physical Dimensions (h x w x d):1.2 x 7 x 4.6 in (31 x 177 x 117 mm) 
Weight:GS605: 0.63 lbs (0.28  kg) / GS608: 0.69 lbs (0.31 kg)
Operating Temperature:0 to 40° C (32 to 104° F)
Electromagnetic Compliance:CE mark, Commercial; FCC Part 15, Class A; EN 55 022 
(CISPR 22) Class A, VCCI Class A, C-Tick
Safety Agency Approvals forCE mark, Commercial UL listed (UL 1950), C-Tickthe Power Adapter: 
Performance Specifications
Frame Filter Rate:14,800 frames/sec max for 10M port/148,800 frames/sec max 
for 100M port/1,488,000 frames/sec max for 1000M port
Frame Forward Rate:14,800 frames/sec max for 10M port / 148,800 frames/sec max 
for 100M port/1,488,000 frames/sec max for 1000M port
Network Latency:1000 Mbps to 1000 Mbps: 20 µs max(using 64-byte packets)
Address Database Size:
4000 MAC addresses
Addressing:48-bit MAC address
Packet Buffer Memory:1 Mb
5 
						

							Technical Support
PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH
YOUR PRODUCT. 
By registering your product at 
www.NETGEAR.com/register, we can provide you with faster
expert technical support and timely notices of product and software upgrades.
©2004 NETGEAR, Inc. NETGEAR, the Netgear logo, Auto Uplink, ProSafe and Everybody's
connecting are trademarks or registered trademarks of Netgear, Inc. in the United States and/or
other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation in
the United States and/or other countries. Other brand and product names are trademarks or
registered trademarks of their respective holders. Information is subject to change without
notice. All rights reserved.
May 2004201-10159-02