Home > Netgear > NAS Systems > Netgear Rn316 Readynas 600 Series 6 Bay Hardware Manual

Netgear Rn316 Readynas 600 Series 6 Bay Hardware Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Netgear Rn316 Readynas 600 Series 6 Bay Hardware Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 137 Netgear manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Power On
    To power on the system:
    1.Connect the system to a power supply.
    Depending on the system's last power state, the system might power on automatically.
    For more information, see Power State on page 51.
    Note
    2.If necessary, press the Power button.
    The system powers on.
    Preferred Shutdown
    You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
    For information about how to gracefully shut down your system using the ReadyNAS local admin page, see
    the ReadyNAS OS 6 Software Manual, which is available at support.netgear.com/product/ReadyNAS-OS6.
    To gracefully shut down your system using the Power button:
    1.Press the Power button.
    The Power LED blinks, prompting you to confirm the shutdown.
    2.Press the Power button again.
    The system shuts down gracefully.
    Forced Shutdown
    Perform a forced shutdown only if the storage system is not responding.
    To perform a forced shutdown:
    •Unplug the system from the power supply.
    Power State
    If the power supply is interrupted due to a power failure, the system returns to its last state when the power
    supply is restored:
    •If the system was powered on at the time of the power failure, the system powers on when the power
    supply is restored.
    •If the system was powered off at the time of the power failure, the system remains off when the power
    supply is restored.
    NETGEAR ReadyNAS 212
    51
    ReadyNAS OS 6.5 
    						
    							Boot Menu
    Use the boot menu to restart or troubleshoot your ReadyNAS storage system.Your storage system has the
    following boot modes:
    •Normal. Initiates a normal boot process, just like booting using the Power button.
    •Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a
    10-minute time-out period begins.
    WARNING:
    The factory default reboot process resets the storage system to factory
    settings, erases all data, resets all defaults, and reformats the disk to X-RAID.
    -If you want to cancel the factory default process, power off the storage system before the 10-minute
    time-out ends.The system powers down safely without causing any data loss.
    -If you want to reset the system to factory default settings, do not power off your system. After the
    10-minute time-out period, the factory default process begins.
    To start the factory default process immediately, press the Backup button during the
    10-minute time-out period.
    Tip
    •OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
    when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
    some settings on your storage system, such as Internet protocol settings and the administrator password,
    to defaults.
    •Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a
    NETGEAR technical support representative instructs you to do so.
    •Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
    data off a disk during a disaster recovery.
    •Memory test. Performs a memory test.The memory test runs for eight hours.The current status and
    the pass or fail result is reported using the storage system LEDs, as described in the following table:
    Figure 17. Memory Test Status
    Backup LEDDisk 2 LEDDisk 1 LEDPower LEDMemory Test State
    BlinkingOffOffOffFirst hour
    OffBlinkingOffOffSecond hour
    OffOffBlinkingOffThird hour
    BlinkingBlinkingBlinkingOffForth hour
    BlinkingOffOffOnFifth hour
    NETGEAR ReadyNAS 212
    52
    ReadyNAS OS 6.5 
    						
    							(Continued)
    Backup LEDDisk 2 LEDDisk 1 LEDPower LEDMemory Test State
    OffBlinkingOffOnSixth hour
    OffOffBlinkingOnSeventh hour
    BlinkingBlinkingBlinkingOnEigth hour
    BlinkingBlinkingBlinkingBlinkingResult: fail
    OnOnOnOnResult: pass
    •Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
    the size of your disks. Any problems are reported in the system logs. For more information about viewing
    the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
    support.netgear.com/product/ReadyNAS-OS6.
    To access the boot menu:
    1.Power off your storage system.
    2.Using a straightened paper clip, press and hold the Reset button.
    3.Press the Power button.
    The system powers on.
    4.Continue to press the Reset button until the Power button LED, USB and backup status LED, disk 1
    LED, and disk 2 LED light.
    5.Press the Backup button to scroll through boot mode options.
    The storage system shows the boot mode options using the LEDs, as described in the following table:
    Status IndicatorBoot Mode
    USB and
    Backup
    LED
    Disk 2
    LED
    Disk 1
    LED
    Power
    LED
    Description
    All four LEDs light.Boot menu
    Power LED lights.Normal
    Disk 1 LED lights.Factory default
    Disk 2 LED lights.OS reinstall
    USB and backup status LED lights.Tech support
    Power LED and disk 1 LED light.Volume read only
    NETGEAR ReadyNAS 212
    53
    ReadyNAS OS 6.5 
    						
    							(Continued)
    Status IndicatorBoot Mode
    USB and
    Backup
    LED
    Disk 2
    LED
    Disk 1
    LED
    Power
    LED
    Description
    Power LED and disk 2 LED light.Memory test
    Power LED and USB and backup status LED
    light.
    Test disk
    Legend:
    •On:
    •Off:
    6.Press and release the Reset button to confirm your boot menu selection.
    The system boots in the selected boot mode.
    NETGEAR ReadyNAS 212
    54
    ReadyNAS OS 6.5 
    						
    							7
    NETGEAR ReadyNAS 214
    This chapter provides an overview of the physical features of the ReadyNAS 214 and includes the following
    sections:
    •Front and Side Panels on page 56
    •Drive Bays on page 56
    •Rear Panel on page 57
    •Status Information on page 58
    •Power On and Shut Down on page 59
    •Boot Menu on page 61
    55 
    						
    							Front and Side Panels
    The following figure shows the front and side panels of the ReadyNAS 214.
    Figure 18. ReadyNAS 214 front and side panels
    1.Exhaust vents
    2.USB 2.0 port
    3.Backup button and LED
    4.Disk LEDs
    5.Disk activity LED
    6.Power button and LED
    7.Drive bay door
    8.Status display screen
    Drive Bays
    The following figure shows the drive bays of the ReadyNAS 214.
    NETGEAR ReadyNAS 214
    56
    ReadyNAS OS 6.5 
    						
    							Figure 19. ReadyNAS 214 drive bays
    1.Drive bay door
    2.Disk tray handle
    3.Recessed disk tray handle lock
    4.Disk tray release latch
    5.Drive bays
    Rear Panel
    The following figure shows the rear panel of the ReadyNAS 214.
    NETGEAR ReadyNAS 214
    57
    ReadyNAS OS 6.5 
    						
    							Figure 20. ReadyNAS 214 rear panel
    1.eSATA port
    2.Reset button
    3.USB 3.0 ports
    4.LAN ports with LED status indicators
    The two LAN ports are equivalent.They can be used as two separate Ethernet
    connections, or can be configured as a single, bonded port with a 2 Gbps potential
    speed. For information about how to configure a bonded port, and the network
    configuration requirements needed to support 2 Gbps, see the ReadyNAS OS 6
    Software Manual, which is available at support.netgear.com/product/ReadyNAS-OS6.
    Note
    5.Power cable socket
    6.Exhaust fan
    7.Kensington lock
    Status Information
    You can obtain information about the status of your storage system by reviewing the indicators listed in the
    following table.
    NETGEAR ReadyNAS 214
    58
    ReadyNAS OS 6.5 
    						
    							Table 6. ReadyNAS 214 indicator descriptions
    DescriptionIndicator
    Press this button to turn on the ReadyNAS.The LED indicates these states:
    •On. Powered on.
    •Blinking. Booting or shutting down.
    •Off. Powered off.
    Power button and LED
    An LED on the top of the front panel is associated with each drive bay. LEDs are in
    numerical order from left to right.The disk LEDs indicate these states:
    •On. Power is on and the disk is operating normally.
    •Blinking.The disk was removed, failed, or is resynchronizing. See the display
    screen for details.
    •Off.The drive bay is empty.
    Disk LEDs (1, 2, 3, 4)
    The disk activity LED indicate these states:
    •Blinking. A disk is being accessed.
    •Off. All disks are idle.
    Disk activity LED
    Two LED status indicators are built into each port, one off or green and one showing
    three states: off, amber, or green.They indicate port speed and activity as follows:
    •Green, green. 1000 Mbps connection speed, no activity.
    •Green blinking, green. 1000 Mbps connection speed, activity.
    •Green, amber. 100 Mbps connection speed, no activity.
    •Green blinking, amber. 100 Mbps connection speed, activity.
    •Green on, off. 10 Mbps connection speed, no activity.
    •Green blinking, off. 10 Mbps connection speed, activity.
    •Off, off. No connection.
    Rear panel Ethernet port
    LEDs
    Displays messages about the status of your storage system. Note that the status
    display screen goes to sleep to prevent burn-in.To wake it, press the Power button
    once. If the storage system reports an abnormal operation or error, the status display
    screen stays on.
    Status display screen
    Power On and Shut Down
    This section describes how to power on and shut down your system. If you must shut down the system, use
    one of the preferred shutdown methods whenever possible.
    NETGEAR ReadyNAS 214
    59
    ReadyNAS OS 6.5 
    						
    							Power On
    To power on the system:
    1.Connect the system to a power supply.
    Depending on the system's last power state, the system might power on automatically.
    For more information, see Power State on page 61.
    Note
    2.If necessary, press the Power button.
    The system powers on.
    Preferred Shutdown
    You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
    For information about how to gracefully shut down your system using the ReadyNAS local admin page, see
    the ReadyNAS OS 6 Software Manual, which is available at support.netgear.com/product/ReadyNAS-OS6.
    To gracefully shut down your system using the Power button:
    1.If the status display screen is not lit, do the following:
    a.Press the Power button.
    The status display screen wakes.
    b.Press the Power button a second time.
    Instructions for graceful shutdown display on the status display screen.
    c.Press the Power button a third time.
    The system shuts down gracefully.
    2.If the status display screen is lit, do the following:
    a.Press the Power button.
    Instructions for graceful shutdown display on the status display screen.
    b.Press the Power button again.
    The system shuts down gracefully.
    Forced Shutdown
    Perform a forced shutdown only if the storage system is not responding.
    To perform a forced shutdown:
    •Unplug the system from the power supply.
    NETGEAR ReadyNAS 214
    60
    ReadyNAS OS 6.5 
    						
    All Netgear manuals Comments (0)

    Related Manuals for Netgear Rn316 Readynas 600 Series 6 Bay Hardware Manual