OKI C130n User Manual
Here you can view all the pages of manual OKI C130n User Manual. The Oki manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 161
161 - C130n User’s Guide 8Load paper into Tray 2. See “Tray 2” on page 65. 9Insert Tray 2 into the printer and reconnect all interface cables. 10Reconnect the power cord, and turn on the printer. 11Activate Tray 2 in the Windows printer driver (Properties/Configure tab, see page 17). Downloaded From ManualsPrinter.com Manuals
Page 162
162 - C130n User’s Guide Duplex Option Duplex printing (printing on both sides of the page) can be performed automatically with the duplex option installed. For more information, see “Duplexing” on page 68. Before installing the duplexer, you must first install one of the following on the printer: !Optional Tray 2 !The duplexing attachment (1) supplied with the Duplexer (2) Installing the Duplexing Attachment Important! If Tray 2 is installed, it is not necessary to install the duplex attachment. In...
Page 163
163 - C130n User’s Guide Important! Since the imaging drum and toners are installed in the printer, be sure to keep the printer level when moving it in order to prevent accidental spills. 1Turn off the printer and discon- nect the power cord and inter- face cables. 2Remove the dust cover from Tray 1. Downloaded From ManualsPrinter.com Manuals
Page 164
164 - C130n User’s Guide 3Close Tray 1 and the output tray. 4Unpack the duplexing attachment. NoteBe sure to place the attachment on a level surface. 5Lift the printer and place it on top of the attachment, making sure that the positioning pins on the attachment correctly fit into the holes on the bottom of the printer. 6Open Tray 1 and the output tray, and reattach the dust cover. Downloaded From ManualsPrinter.com Manuals
Page 165
165 - C130n User’s Guide Installing the Duplexer NoteThe illustrations in the following installation procedure show the printer with Tray 2 installed; however, the installation procedure would be the same if the attachment was installed. 1Turn off the printer and discon- nect the power cord and inter- face cables. 2Remove the tape affixed to the rear cover. 3Unpack the duplexer. Downloaded From ManualsPrinter.com Manuals
Page 166
166 - C130n User’s Guide 4Install the duplexer. Align the duplex option with its installation position, and then push down on the bottom of the duplex option until it locks into place. Important! When attaching the duplex option, attach the bottom of the option first. If the duplex option is attached incorrectly, it may be damaged. Downloaded From ManualsPrinter.com Manuals
Page 167
167 - C130n User’s Guide 5Open the duplex cover. While holding the duplex option against the printer, tighten the screws inside the cover to complete the installation of the duplex option. 6Reconnect all interface cables. 7Reconnect the power cord, and turn on the printer. 8Activate the duplexer in the Windows printer driver (Properties/Configure tab, see page 17). Downloaded From ManualsPrinter.com Manuals
Page 169
169 - C130n User’s Guide Printer Specifications Ty p eDesktop full color laser beam printer Printing systemDual laser diode with polygon mirror Developing systemMono component development system Fusing systemHeat roller system Resolution600 dpi × 600 dpi × 4 bits or 600 dpi × 600 dpi × 1 bit First printSimplex Monochrome: 13.0 seconds for A4, Letter (plain paper) Full color: 22.0 seconds for A4, Letter (plain paper) Duplex Monochrome: 26.0 seconds for A4, Letter (plain paper) Full color: 35.0...
Page 170
170 - C130n User’s Guide Media sizesTray 1 Paper width: 92 to 216 mm (3.6 to 8.5) Paper length: Plain paper: 195 to 356 mm (7.7 to 14.0) Thick stock 1/2: 184 to 297 mm (7.25 to 11.7) Tray 2 (Optional) A4/Letter Paper/MediaPlain paper (60 to 90 g/m2; 16 to 24 lb bond) Thick stock 1 (91 to 163 g/m2) Thick stock 2 (164 to 209 g/m2) Postcard Letterhead Label sheet Input capacityTray 1 Plain paper: 200 sheets Label/Letterhead/Postcard/Thick Stock: 50 sheets Tray 2 (Optional) Plain paper: 500 sheets Output...