OKI C5600N User Manual

							Menu functions> 71
TRAY2 
MEDIAWEIGHTLIGHT (64-
74g/m²)
MEDIUM (75-
90g/m²)
HEAVY (91-
176g/m²)Adjusts the printer for the weight of 
paper stock loaded in this tray (if 
installed).
MPT PAPERSIZE LETTER
EXECUTIVE
LEGAL14
LEGAL13.5
LEGAL13
A4 / A5 / A6 / 
B5
CUSTOM
COM-9 
ENVELOPE
COM-10 
ENVELOPE
MONARCH ENV
DL ENVELOPE
C5 ENVELOPESelects the size of paper to be fed 
from the multi purpose tray. For 
CUSTOM setting see X-DIMENSION 
and Y-DIMENSION later in this table.
MPT MEDIATYPEPLAIN
LETTERHEAD
TRANSPARENC
Y
LABELS
BOND
RECYCLED
CARD STOCK
ROUGH
GLOSSYSelects the type of media to be fed 
from the multi purpose tray so that 
the printer can adjust its internal 
parameters to better accommodate 
the selected type of media.
MPT 
MEDIAWEIGHTMEDIUM (75-
90g/m²)
HEAVY (91-
120g/m²)
ULTRA HEAVY 
(121-203g/m²)Selects the media weight to be fed 
from the multi purpose tray.
UNIT OF 
MEASUREMILLIMETRE
INCHSelects the unit of measure for the 
next two items.
X-DIMENSION 100-210-216 
MILLIMETRESelects the width of paper defined by 
the “CUSTOM” settings referred to in 
the foregoing PAPER SIZE settings.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 72
Y- D I M E N S I O N148-297-1200 
MILLIMETRESelects the length of paper defined 
by the “Custom” settings referred to 
in the foregoing PAPER SIZE 
settings. Note that media of up to 
1200mm in length can be fed from 
the multi purpose tray for banner 
printing.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 73
COLOUR MENU
The printer automatically adjusts colour balance and density at 
appropriate intervals, optimising the printed output for bright 
white paper viewed in natural daylight conditions. The items on 
this menu provide a means of changing the default settings for 
special or particularly difficult print jobs. Settings revert to their 
default values when the next print job is complete.
ITEMSETTINGSEXPLANATION
DENSITY 
CONTROLAUTO
MANUALIf set to AUTO, image density will be 
automatically adjusted at power on, 
when a new image drum or toner 
cartridge is installed, and at intervals 
of 100, 300 and 500 drum counts. If 
a 500 drum count interval occurs 
during a print job it will occur at the 
end of that job, and will take up to 
55 seconds. If set to manual, this 
adjustment will only be performed 
when initiated by the next menu 
item.
ADJUST 
DENSITYEXECUTESelecting this will permit adjustment 
of the colour density.
AJST 
REGISTRATIONEXECUTE Performs automatic colour 
registration adjustment. Normally 
this is done on power on and when 
the top cover is opened and then 
closed. This process accurately 
aligns the cyan, magenta and yellow 
images to the black image.
C REG FINE 
AJST
M REG FINE 
AJST
Y REG FINE 
AJST
-3~0~+3
-3~0~+3
-3~0~+3Performs fine adjustment of image 
timing in relation to the black image 
component.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 74
SYSTEM CONFIGURATION MENU
This menu adjusts general printer settings to suit the way you 
prefer to work.
ITEMSSETTINGSEXPLANATION
POW SAVE TIME 5
15
30
60
240Adjusts the idling time before the 
printer automatically switches into 
power saving mode. In this mode 
power consumption is reduced to a 
low level required to just keep the 
printer operating and ready to 
receive data. When a job is sent the 
printer will require a warm-up time 
o f  u p  t o  1  m i n u t e  b e f o r e  p r i n t i n g  c a n  
begin.
CLRABLE 
WARNINGON
JOBWhen ON, non-critical warnings, 
such as requests for a different 
paper size, can be cleared by 
pressing the 
ON LINE button. 
When set to JOB, they are cleared 
when the print job resumes.
MANUAL 
TIMEOUTOFF
30
60Specifies how many seconds the 
printer will wait for paper to be fed 
before cancelling the job.
WAIT TIMEOUT5~40~300Specifies how many seconds the 
printer will wait when received data 
pauses before forcing a page eject. 
In PostScript Emulation mode the 
job will be cancelled if timeout 
occurs.
LOW TONERCONTINUE
STOPSpecifies whether the printer should 
continue printing even after a low 
toner condition is detected.
JAM RECOVERYON
OFFSpecifies whether the printer should 
perform jam recovery after a paper 
jam has occurred. If ON, the printer 
will attempt to print again any pages 
lost due to a paper jam once the jam 
has been cleared.
ERROR REPORT ON
OFFIf ON, the printer will print error 
details when a PostScript Emulation 
error occurs.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 75
USB MENU
This menu controls the operation of the printer’s USB data 
interface.
NETWORK MENU
This menu controls the operation of the printer’s 10Base-T/
100Base-TX network interface.
ITEMSETTINGSEXPLANATION
SOFT RESET ENABLE / 
DISABLEEnables or disables the SOFT RESET 
command.
SERIAL NUMBERENABLE / 
DISABLE
SPEED 12 / 480 Mps Selects the interface speed
ITEMSETTINGSEXPLANATION
TCP/IPENABLE / 
DISABLEEnables or disables this network 
protocol.
NETBEUIENABLE / 
DISABLEEnables or disables this network 
protocol.
IP ADDRESS 
SETAUTO / MANUAL Specifies whether IP address 
allocation is automatic (DHCP) or 
manually assigned.
IP ADDRESSxxx.xxx.xxx.xxxCurrent assigned IP address. To 
change, press ENTER and use 
+/– 
keys to increment 1st octet, then 
press ENTER again to move on to 
next octet. When 4th octet has been 
set, press ENTER again to register 
new address.
SUBNET MASK xxx.xxx.xxx.xxx Current assigned subnet mask. To 
change, proceed as above.
GATEWAY 
ADDRESSxxx.xxx.xxx.xxxCurrent assigned gateway address. 
To change, proceed as above.
FAC TO RY 
DEFAULTSEXECUTE Reloads the settings present when 
the unit was setup by the 
manufacturer.
WEBENABLE / 
DISABLEEnables or disables Web config. 
facility.
TELNET ENABLE / 
DISABLEEnables or disables Telnet config. 
facility.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 76
MAINTENANCE MENU
This menu provides access to various printer maintenance 
functions.
FTPENABLE / 
DEFAULTEnables or disables communication 
via FTP.
SNMPENABLE / 
DISABLEEnables or disables SNMP protocol.
NETWORK 
SCALENORMAL / 
SMALLSelects network size.
HUB LINK 
SETTINGAUTO 
NEGOTIATE
100BASE-TX 
FULL
100BASE-TX 
HALF
10BASE-T FULL
10BASE-T HALFSets full or half duplex for 
communication via a network hub.
ITEMSETTINGSEXPLANATION
ITEMSETTINGSEXPLANATION
MENU RESET EXECUTE Resets menus to default settings.
SAVE MENUEXECUTESaves current menu settings as 
default values. At confirmation 
prompt, press ENTER to confirm 
save, or CANCEL to cancel.
POWER SAVEENABLE / 
DISABLEEnables or disables automatic power 
save mode. Delay before entering 
this mode is set in the system 
configuration menu.
PAPER BLACK 
SETTING–2~0~+2Used for small adjustment when you 
experience faded print or light 
specks / streaking in monochrome 
printing on white paper. Select a 
higher value to reduce fading, or a 
lower value to reduce specks or 
streaking in high density print areas.
PAPER COLOR 
SETTING–2~0~+2 As above, but for colour printing.
TRANSPR 
BLACK SETTING–2~0~+2As above but for mono printing on 
transparencies.
TRANSPR 
COLOR SETTING–2~0~+2 As above but for colour printing on 
transparencies.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 77
USAGE MENU
This menu is for information only, and provides an indication of 
total usage of the printer and the expected life left in its 
consumable items. This is particularly useful if you do not have a 
full set of replacement consumables to hand and you need to 
know how soon you will need them.
ITEMEXPLANATION
TRAYn PAGE COUNT The total number of pages fed from tray n.
MPT PAGE COUNTThe total number of pages fed from the multi 
purpose tray.
COLOR PAGE COUNT The total number of pages printed in colour.
MONO PAGE COUNTThe total number of pages printed in 
monochrome.
K DRUM LIFE 
REMAINING
C DRUM LIFE 
REMAINING
M DRUM LIFE 
REMAINING
Y DRUM LIFE 
REMAININGPercentage of life remaining in these consumable 
items.
BELT LIFE 
REMAININGPercentage of belt life remaining.
FUSER LIFE 
REMAININGPercentage of fuser life remaining.
K TONER
C TONER
M TONER
Y TONER
Cartridge size and current toner level.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing consumable items> 78
REPLACING CONSUMABLE ITEMS
This section explains how to replace consumable items when due. 
As a guide, the life expectancy of these items is:
>Toner:
The C
5600 is shipped with sufficient Cyan, Magenta & Yellow 
toner for 2,000 A4 pages in the print cartridges, of which 800 A4 
pages of toner are used to charge the image drum (1,200 A4 
pages remaining).
The C580
0 is shipped with sufficient Cyan, Magenta & Yellow 
toner for 5,000 A4 pages in the print cartridges, of which 
800 A4 pages of toner are used to charge the image drum 
(4,200 A4 pages remaining).
Both models are shipped with sufficient Black toner for 
6,000 A4 pages in the print cartridges, of which 800 A4 
pages of toner are used to charge the image drum (5,200 
A4 pages remaining).
>Image drum: Approximately 20,000 pages (calculated on 
typical office usage where 20% of printing is 1 page only, 
30% is 3 page documents and 50% is print runs of 15 
pages or more).
>Transfer belt: Approximately 60,000 A4 pages.
>Fuser: Approximately 60,000 A4 pages.
A4 PAGE COVERAGE 
(OF THIS COLOUR)2.5%5.0%10%
Black C5600 12,000 6,000 3,000
C580012,0006,0003,000
Cyan C5600 4,000 2,000 1,000
C580010,0005,0002,500
Magenta C5600 4,000 2,000 1,000
C580010,0005,0002,500
Yellow C5600 4,000 2,000 1,000
C580010,0005,0002,500
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing consumable items> 79
CONSUMABLE ORDER DETAILS
* Average life: 20% pages at continuous print, 50% pages at 3 
pages per job and 30% pages at 1 page per job.
Only use genuine Oki Original consumables to ensure the 
best quality and performance from your hardware. Non 
Oki Original products may adversely affect your printers 
performance and invalidate your warranty.
ITEMLIFEORDER 
NO.
Toner, C5800, black 6,000 A4 @ 5%* 43324424
Toner, C5800, cyan5,000 A4 @ 5%*43324423
Toner, C5800, magenta 5,000 A4 @ 5%* 43324422
Toner, C5800, yellow5,000 A4 @ 5%*43324421
Toner, C5600, black 6,000 A4@ 5%* 43324408
Toner, C5600, cyan2,000 A4@ 5%*43381907
Toner, C5600, magenta 2,000 A4@ 5%* 43381906
Toner, C5600, yellow2,000 A4@ 5%*43381905
Image drum, C5800, black 20,000 A4 pages* 43381724
Image drum, C5800, cyan20,000 A4 pages*43381723
Image drum, C5800, magenta 20,000 A4 pages* 43381722
Image drum, C5800,yellow20,000 A4 pages*43381721
Image drum, C5600, black 20,000 A4 pages* 43381708
Image drum, C5600, cyan20,000 A4 pages*43381707
Image drum, C5600, magenta 20,000 A4 pages* 43381706
Image drum, C5600, yellow20,000 A4 pages*43381705
Fuser 60,000 A4 pages* 43363203
Tr a n s p o r t  b e l t60,000 A4 @ 3/job43363402
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing consumable items> 80
TONER CARTRIDGE REPLACEMENT
The toner used in this printer is a very fine dry powder. It is 
contained in four cartridges: one each for cyan, magenta, yellow 
and black.
Have a sheet of paper handy so that you have somewhere to 
place the used cartridge while you install the new one.
Dispose of the old cartridge responsibly, inside the pack that the 
new one came in. Follow any regulations, recommendations, etc., 
which may be in force concerning waste recycling.
If you do spill any toner powder, lightly brush it off. If this is not 
enough, use a cool, damp cloth to remove any residue.
Do not use hot water, and never use solvents of any kind. They 
will make stains permanent.
Switch off the printer and allow the fuser to cool for about 
10 minutes before opening the cover.
1.Press the cover release and open the printer’s top cover 
fully.
CAUTION!
To avoid toner wastage and possible toner sensor 
errors, do not change the toner cartridge(s) until 
“TONER EMPTY” is displayed.
WARNING!
If you inhale any toner or get it in your eyes, drink a 
little water or bathe your eyes liberally in cold water. 
Seek medical attention immediately.
WARNING!
If the printer has been powered on, the fuser may be 
hot. This area is clearly labelled. Do not touch.
Downloaded From ManualsPrinter.com Manuals