Panasonic 8415 Maintenance Manual

							Settings and Printing
MaintenanceSpecifications21
8#Turn the fuser unit’s green knob clockwise.
$Remove the jammed media.
OR
9Replace the cleaning pad.
$#
Clearing a Jam 
						

							Settings and Printing
MaintenanceSpecifications22
10#Replace the oil supply roll into the fuser unit.
$Press down firmly on the oil supply roll to snap both sides into place.
%If the oiled cloth is loose, rotate the gear (A) clockwise until it is tight.
NOTE
BDo not touch the oiled cloth.
CAUTION
BIf the oil supply roll is not installed correctly, print quality will be diminished.
$
#
$
Oiled clothA
Clearing a Jam
% 
						

							Settings and Printing
MaintenanceSpecifications23
11#Open the front door.
$Slide the fuser unit back into the printer.
12#Turn the small green thumbscrew clockwise to lock the fuser unit.
$Close the front door.
NOTE
·The error message “Jam at C” is cleared by sliding out the fuser unit, then sliding it back to
the printer.
#$
#
$Clearing a Jam 
						

							Settings and Printing
MaintenanceSpecifications24
nJam at D when printing face down :
1#Open the front door.
$Pull open the access door (above the plastic output tray); see if the media
is visible.
Jam at D
#$Clearing a Jam
(Continued) 
						

							Settings and Printing
MaintenanceSpecifications25
2#Turn the large green knob on the fuser unit counterclockwise.
$Remove the media from inside the access door.
CAUTION
BIf the knob of the fuser unit will not turn, do not force it, or you may damage the fuser unit.
Instead, follow these steps:
a) Unlock the fuser unit by turning the small green thumbscrew counterclockwise.
b) Pull the fuser unit out. The media will probably tear.
c) Remove the oil supply roll.
d) Turn the fuser unit’s large green knob to release the jammed media.
e) Remove the jammed media from the fuser unit and the printer.
SAFETY CAUTION
BThe fuser unit is hot; to avoid personal injury, turn off the printer and wait 10 minutes for the
fuser unit to cool before touching it.
3Close the front door.
#
$Clearing a Jam
! 
						

							Settings and Printing
MaintenanceSpecifications26
nJam at D when printing face up:
1#Open the front door and the right side door.
$Turn the fuser unit’s large green knob counterclockwise to release the
jammed media.
%Remove the jammed media from the right side of the printer.
2Close the front door and the right side door.
#
$%
Clearing a Jam 
						

							Settings and Printing
MaintenanceSpecifications27
1Remove the jammed media from the output tray.
2Open and close the front door to clear the error message from the LCD.
1Remove the jammed media from the multi-purpose tray.
2Open and close the front door to clear the error message from the LCD.
Jam at E
Jam at MPT (Multi-purpose tray)
Clearing a Jam 
						

							Settings and Printing
MaintenanceSpecifications28
1Pull open the access door (above the plastic output tray) and remove the
jammed media.
2Open and close the front door to clear the error message from the LCD.
¾ OR ¾
1Perform steps 1 through 5 of Jam at G, H (seepage 29-30).
Jam at F
#$Clearing a Jam 
						

							Settings and Printing
MaintenanceSpecifications29
1Remove the auto duplex printing unit.
2Open the lid of auto duplex printing unit while squeezing the green knobs.
Jam at G, H
Clearing a Jam 
						

							Settings and Printing
MaintenanceSpecifications30
3Remove the jammed paper.
4Close the lid and press down firmly on it to snap both sides into place.
5Reinsert the auto duplex printing unit.
Clearing a Jam