Panasonic Aj D750 Operating Instructions Manual

Connections with editing controller
Recorder
AV monitor
Video monitor signals
Audio monitor signals
To REMOTE IN/OUT
connector
AV monitor
Editing Controller
Source machine
AV monitorAV switcher
Remote
To REMOTETo REMOTE
IN/OUT connectorIN/OUT connectorReference
signal generator
Reference signal
Source machine
AV monitor

When an editing controller
made by CMX is used,
support must be provided at
the editing controller side.
-21- 

Connections for adjusting video output (encoder output) signals
REF
(BB)
Player 1
(source machine 1)REF
(BB)
Player 2
(source machine 2)
REF RECORDER
(BB)
REF REF
REF
VIDEO INVIDEO IN VIDEO IN
VIDEO 1VIDEO 1VIDEO IN
OUT OUT
REF (BB)
P1 IN P2 IN
REF IN
SwitcherRECORDER OUT
MONITOR OUT
Supply the external reference signal from a
sync signal generator to the units. Use the composite connectors for the video
signals. TV
WFM VSC
monitor(waveform monitor)(vectorscope)
75
REF (BB)
Make these two
cables equally...

Tapes
Three types of tapes can be used with the unit.
Type
Consumer
cassette
News-
gathering
cassette
General
purpose
cassette
Description
Tape designed exclusively for the camcorders
used by consumers in general. Only playback
is possible using the optional cassette adaptor.
Recording/playback tape with a maximum
capacity of 63 minutes.
(AJ-P6MP, AJ-P12MP, AJ-P23MP, AJ-P33MP,
AJ-P63MP)
Recording/playback tape with a maximum
capacity of 123 minutes.
(AJ-P64LP, AJ-94LP, AJ-P123LP)
Align the cassette with...

Switching on the power/inserting the cassette
Before starting to operate the unit, check whether the equipment has been connected
properly.
Turn on the power.
Check that the AUTO OFF lamp is off.
When condensation has formed or some other trouble has occurred, the AUTO OFF
lamp lights, and all operations are disabled.
Insert the cassette tape.
Insert the tape at its proper position without force.
Check that the STOP lamp is on.
When the tape is inserted, the cylinder rotates automatically, the tape is...

STOP/STAND BY mode
When the STOP button is pressed, the unit goes into the stop mode.The STOP lamp
lights and the tape stops traveling.
In order to protect the tape, the unit goes into the standby OFF mode after the time
set by setting menu No.400 (STILL TIMER) has elapsed. When the STOP, REW, FF
or PLAY button is pressed, the unit will go into the appropriate mode.
When the STAND BY button is pressed, the unit goes into the standby ON/OFF mode.
When the button’s lamp is lighted, the unit is in the...

Recording
Set the accidental erasure prevention tab on the cassette tape to the “recording”
position and insert the tape.
Press the STOP button to place the unit in the stop mode.
Set the MODE switch to EE.
EE images now appear on the TV monitor.
Check that the REC INHIBIT lamp is off.
If this lamp is lighted, set the REC INHIBIT switch to OFF.
Select the video and audio input signals and adjust their levels.
5-1Selecting video/audio input signals
1
Connect the signals to be recorded.
2 Select the input...

Playback
Insert the cassette tape, and place the unit in the stop mode.
Press the PLAY button.
Regular playback is now commenced.
Adjust the audio playback level.
Pull out the audio level controls and turn them clockwise or counterclockwise to adjust
the levels. Normally, they are kept in the pushed-in state (unity value).
To end playback, press the STOP button.
The VTR now goes into the stop mode.

Check that the SERVO lamp is lighted during playback. If it flashes or if it is off, the
images played...

Jog/shuttle modes
Jog mode
Push the search dial to the “in” position.
Be sure that the JOG lamp lights.
Rotate the search dial.
The dial’s clickstops are cleared, and the tape is played back at the speed (–0.43 × to
+1 
× normal speed) corresponding to the speed at which the dial is turned. When the
dial rotation is stopped, a still picture appears. The playback picture is noise-free.
To transfer from the jog mode to another mode, press the appropriate button.
Shuttle mode
Push the search dial to release...

Manual editing
Select the editing mode.
ASSEMBLE: For assemble editing.
INSERT:For insert editing.
Select the editing channel.
In the case of insert editing, press the channel button corresponding to the signals to
be edited, and check that its lamp is on.
Press the PLAY button.
Search for the position where the editing is to be commenced (IN point) while viewing
the TV monitor, and press the PLAY and EDIT buttons together at the IN point.
Press the STOP or PLAY button at the position where editing is to...

Preroll
Press the PREROLL button.
The VTR now performs the preroll operation.
When the edit IN point has been entered, the tape is rewound from the edit IN point
for the duration set by setting menu “000,” and the unit then goes into the stop mode.
When the edit IN point has not been entered, the tape is rewound for the duration set
by setting menu “000” from the position where the button was pressed, and the unit
then goes into the stop mode.

The time code or CTL signal must be continuously recorded...