Panasonic Aj-D950 Aj-Pd950 Operating Instructions Manual
Have a look at the manual Panasonic Aj-D950 Aj-Pd950 Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 75
Ð 76 Ð
RS-232C interface
1. Introduction
(1) The VTR can be operated by commands when the RS-232C interface is used.
(See command table on page 79 Ð 81.)
(2) Conditions for acknowledging commands from RS-232C interface
The front panel REMOTE/LOCAL switch must be at REMOTE.
The setup menu item No. 204 ÒRS232C SELÓ must be ON.
If the above conditions are not met, [ACK] + [STX]ER001[EXT] is returned to the external unit.
Whether the [ACK] code is returned depends on the setting which has been selected for...](http://img.usermanuals.tech/thumb/58/67764/w64_aj-d950.aj-pd950_en_om_d-74.png "Page 75
Ð 76 Ð
RS-232C interface
1. Introduction
(1) The VTR can be operated by commands when the RS-232C interface is used.
(See command table on page 79 Ð 81.)
(2) Conditions for acknowledging commands from RS-232C interface
The front panel REMOTE/LOCAL switch must be at REMOTE.
The setup menu item No. 204 ÒRS232C SELÓ must be ON.
If the above conditions are not met, [ACK] + [STX]ER001[EXT] is returned to the external unit.
Whether the [ACK] code is returned depends on the setting which has been selected for...")
![Page 77
Ð 78 Ð
RS-232C interface
3) Return format [VTR ® controller (PC)]
The following responses are made to the command. If necessary, more than one response is made.
n When the communication has terminated normally
1. The receive completion message is returned.
[ACK]
06h
2. The execution completion message is returned.
[STX] [command] [data] [ETX]
02h XX XX XX XX-XX 03h
¥[command]: This is the message (data) which is returned or the execution completion message identifier.
¥[data]: This is the...](http://img.usermanuals.tech/thumb/58/67764/w64_aj-d950.aj-pd950_en_om_d-76.png "Page 77
Ð 78 Ð
RS-232C interface
3) Return format [VTR ® controller (PC)]
The following responses are made to the command. If necessary, more than one response is made.
n When the communication has terminated normally
1. The receive completion message is returned.
[ACK]
06h
2. The execution completion message is returned.
[STX] [command] [data] [ETX]
02h XX XX XX XX-XX 03h
¥[command]: This is the message (data) which is returned or the execution completion message identifier.
¥[data]: This is the...")
![Page 78
Ð 79 Ð
5. Command table
(1) Commands relating to operation control
¥As for the return (completion) message, [ACK] is first returned when data is received, and the execution message is
subsequently returned. It is only the execution message which is listed in this table.
¥In the case of commands not listed in the table, ER001 (invalid command) is returned after [ACK] has been returned.
VTR
operationSend commandReturn (completion)
messageSupplementary notes
[STX] OSP [ETX] STOP
[STX] OSP [ETX]This command...](http://img.usermanuals.tech/thumb/58/67764/w64_aj-d950.aj-pd950_en_om_d-77.png "Page 78
Ð 79 Ð
5. Command table
(1) Commands relating to operation control
¥As for the return (completion) message, [ACK] is first returned when data is received, and the execution message is
subsequently returned. It is only the execution message which is listed in this table.
¥In the case of commands not listed in the table, ER001 (invalid command) is returned after [ACK] has been returned.
VTR
operationSend commandReturn (completion)
messageSupplementary notes
[STX] OSP [ETX] STOP
[STX] OSP [ETX]This command...")
![Page 79
Ð 80 Ð
VTR
operationSend commandReturn (completion)
messageSupplementary notes
[STX] OBF [ETX] STANDBY
OFF[STX] OBF [ETX]This command is setting the VTR to standby OFF.
[STX] OSR:data [ETX] SHTL
REVERSE[STX] OSR [ETX]This is the reverse direction shuttle command.
data = n:
0:
1:
2:
3:
4:
5:
6:
7:
8:
9:
A:speed data
STILL
´0.03
´0.1
´0.2
´0.5
´1
´1.85
´4.1
´9.5
´16
´32: This speed differs according to the setting selected for
setup menu No. 101 (SHTL MAX).
: This speed differs according to the...](http://img.usermanuals.tech/thumb/58/67764/w64_aj-d950.aj-pd950_en_om_d-78.png "Page 79
Ð 80 Ð
VTR
operationSend commandReturn (completion)
messageSupplementary notes
[STX] OBF [ETX] STANDBY
OFF[STX] OBF [ETX]This command is setting the VTR to standby OFF.
[STX] OSR:data [ETX] SHTL
REVERSE[STX] OSR [ETX]This is the reverse direction shuttle command.
data = n:
0:
1:
2:
3:
4:
5:
6:
7:
8:
9:
A:speed data
STILL
´0.03
´0.1
´0.2
´0.5
´1
´1.85
´4.1
´9.5
´16
´32: This speed differs according to the setting selected for
setup menu No. 101 (SHTL MAX).
: This speed differs according to the...")
![Page 80
Ð 81 Ð
(2) Commands relating to inquiries
¥As for the return (completion) message, [ACK] is first returned when data is received, and the execution message is
subsequently returned. It is only the execution message which is listed in this table.
¥In the case of commands not listed in the table, ER001 (invalid command) is returned after [ACK] has been returned.
VTR
operationSend commandReturn (completion)
messageSupplementary notes
[STX] QCD [ETX] CTL/TC
DATA
REQUEST
[STX] CD data [ETX]This command is...](http://img.usermanuals.tech/thumb/58/67764/w64_aj-d950.aj-pd950_en_om_d-79.png "Page 80
Ð 81 Ð
(2) Commands relating to inquiries
¥As for the return (completion) message, [ACK] is first returned when data is received, and the execution message is
subsequently returned. It is only the execution message which is listed in this table.
¥In the case of commands not listed in the table, ER001 (invalid command) is returned after [ACK] has been returned.
VTR
operationSend commandReturn (completion)
messageSupplementary notes
[STX] QCD [ETX] CTL/TC
DATA
REQUEST
[STX] CD data [ETX]This command is...")
Ð 82 Ð
RS-232C interface
(3) Microsoft QuickBASIC sample program
CLS
STX$ = CHR$(&H2): ETX$ = CHR$ (&H3): NAK$ = CHR$(15): ACK$ = CHR$(&H6)
PRINT *** RS-232C COMMUNICATION SAMPLE PROGRAM ***
PRINT Type Command QUIT to quit.
PRINT
REM *** Communication Port Initial & Open ***
REM Port 1,9600Bps,No parity,8 bit data,1 stop bit
OPEN COM1:9600,N,8,1 FOR RANDOM AS #1 LEN = 256
REM *** Input Command & Send Command ***
SendCmd:
INPUT Input Command =; SEND$
IF SEND$ = QUIT THEN GOTO ProgEnd
PRINT #1, STX$ + SEND$ + ETX$
REM *** Wait for Receive Command ***
WHILE LOC(1) = 0
WAITKEY$ = INKEY$
IF WAITKEY$ = Q THEN PRINT *** Quit ***: GOTO ProgEnd
WEND
REM *** Receive Command ***
RecvCmd:
RECV$ = INPUT$(1, #1)
IF RECV$ = STX$ THEN RECV$ = [Stx]
IF RECV$ = ACK$ THEN RECV$ = [Ack]
IF RECV$ = NAK$ THEN RECV$ = [Nak]
IF RECV$ = ETX$ THEN BUFFER$ = BUFFER$ + [Etx]: GOTO DispOut
BUFFER$ = BUFFER$ + RECV$
GOTO RecvCmd
REM *** Output Receive Command ***
DispOut:
PRINT Receive Command =; BUFFER$
PRINT
BUFFER$ =
GOTO SendCmd
REM *** End Program ***
ProgEnd:
CLOSE
END
MICROSOFT QUICKBASIC is a registered trade mark of Microsoft Corporation.
Ð 83 Ð Pin No. Signal 1 2 3GND HOT COLD Connector signals VIDEO IN SERIAL IN (DIGITAL) BNC ´ 2 Active through Y, PB, PR (ANALOG) BNC ´ 3 VIDEO IN BNC ´ 2Loop-through, 75W termination switch provided (Board, option) REF VIDEO IN BNC ´ 2Loop-through, 75W termination switch provided VIDEO OUT SERIAL OUT (DIGITAL) BNC ´ 3 Y, PB, PR (ANALOG) BNC ´ 3 VIDEO OUT BNC ´ 3 AUDIO IN SERIAL IN (DIGITAL) BNC ´ 2 Active through AUDIO IN (DIGITAL) XLR ´ 2 CH1/CH2, CH3/CH4 AES/EBU format AUDIO IN (ANALOG) XLR ´ 2 CH1, CH2, CH3, CH4 CUE IN XLR ´ 1 TIME CODE IN XLR ´ 1 AUDIO OUT SERIAL OUT (DIGITAL) BNC ´ 3 AUDIO OUT (DIGITAL) XLR ´ 2 CH1/CH2, CH3/CH4 AES/EBU format AUDIO OUT (ANALOG) XLR ´ 2 CH1, CH2, CH3, CH4 CUE OUT XLR ´ 1 TIME CODE OUT XLR ´ 1 MONITOR OUT XLR ´ 2 HEADPHONES (front) M6 RS-422A REMOTE (9P) REMOTE IN/OUT Pin No.SignalPin No.SignalPin No.Signal 1 FRAME GROUND 4RECEIVE COMMON7 TRANSMIT B 2 TRANSMIT A 5ÑÑÑÑÑ 8RECEIVE A 3 RECEIVE B 6TRANSMIT COMMON9 FRAME GROUND REMOTE OUT Pin No.SignalPin No.SignalPin No.Signal 1 FRAME GROUND 4TRANSMIT COMMON7 RECEIVE B 2 RECEIVE A 5ÑÑÑÑÑ 8TRANSMIT A 3 TRANSMIT B 6RECEIVE COMMON9 FRAME GROUND
Ð 84 Ð Connector signals PARALLEL REMOTE (25P) Pin No.SignalPin No.SignalPin No.Signal 1 PLAY COMMAND 10ÑÑÑÑÑ 1 9STAND BY ON STATUS 2 STOP COMMAND 11ÑÑÑÑÑ 2 0PREROLL STATUS 3 FF COMMAND 12³10V, MAX 300mA 21SERVO LOCK STATUS 4 REW COMMAND 13 PLAY STATUS 22ÑÑÑÑÑ 5 REC COMMAND 14 STOP STATUS 23ÑÑÑÑÑ 6 EJECT COMMAND 15 FF STATUS 24ÑÑÑÑÑ 7STAND BY ON/OFF COMMAND16 REW STATUS 25 GND 8PREROLL COMMAND17 REC STATUS 9 IN SET COMMAND 18 EJECT STATUS ¥COMMAND pins: TTL level, active low, ³100ms edge electrical signal. ¥STATUS pins: open collector, sink current 6 mA RS-232C REMOTE (25-pin D-SUB crossover cable supported) Pin No. Abbreviation Circuit Description 1 FRAME GROUND Protective ground Frame ground 2 RxD Received data Sends data to the PC. 3 TxD Transmitted data Receives data from the PC. 4 CTS Clear to send Shorted with pin 5. 5 RTS Request to send Shorted with pin 4. 6 DTR Data terminal ready No processing 7 GND Signal ground Signal ground 20 DSR Data set readyPositive power output after communication enable status ENCODER REMOTE (15P) Pin No.SignalPin No.SignalPin No.Signal 1 ÑÑÑÑÑ 6SYSTEM H 0 11 RET GND 2 SET UP 7SYS.SC COARSE (2)1 2 ÑÑÑÑÑ 3 C LEVEL 8 Ð12V 13ÑÑÑÑÑ 4 GND 9 HUE 14 SYS.SC FINE 5 +12V 10 VIDEO LEVEL 15SYS.SC COARSE (1) (Video output connector)Analog component output: (option) Analog composite output: