Panasonic Aj Ec3 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Aj Ec3 Operating Instructions Manual. The Panasonic manuals for Control panel are available online for free. You can easily download all the documents as PDF.
Page 2
E-1 CONTENTS Thank you for purchasing this AJ-EC3 Extension Control Unit (which will subsequently be referred to in these instructions as “the unit”). The unit features high performance and a variety of functions for supporting DVCPRO, DVCPRO50 and DVCPRO HD camera recorders. Features ..............................................................................E-2 Before use ..........................................................................E-3 System connections...
Page 3
E-2 English Features 1. The unit can be used to operate the VTR sections of DVCPRO, DVCPRO50 and DVCPRO HD camera recorders. ≥An ENABLE switch is provided to safeguard against operating errors. ≥VTR warnings are indicated by an LED. 2. Video signals with characters added (SETUP menus, etc.) can be output from the unit’s VIDEO OUT connector. ≥Since the SETUP menus are not displayed on the viewfinder of the camera recorder, the camera can be controlled using the AJ-EC3P’s...
Page 4
E-3 Before use The unit’s functions may be restricted by the type of camera recorder used. Before use, therefore, check the camera recorder model and the functions which can be used with it. Consult your dealer if a model not listed in the above table is going to be used.AJ- D910WA D610WAModel Functions which can be used Mode 1 All the unit’s functions can be used. However, any old versions of the software must be upgraded so consult your dealer about this. AJ- HDC20A BS900 Mode 2 Video signals cannot...
Page 5
English E-4 System connections The unit is connected to a camera recorder, monitor, etc. for use. The examples illustrated here show the system connections for mode 1 and modes 2/3. ECUECU AJ- RB 65 ∫1 Mode 1 Camera recorder Monitor BNC cable BNC cable6-pin cable To VIDEO IN connector To VIDEO OUT connector To VIDEO OUT connector AJ-EC3P To CAM/BS connector To ECU connectorCable (included)
Page 6
E-5 System connections The BNC cable end of the cable (included) is not used in mode 2 or 3. Run it alongside the 6-pin cable and secure it. ≥For details on the connection of the camera recorder, monitor or other units, refer to their respective Operating Instructions. ≥An RCOP cable must be obtained separately if the model AJ-BS900P is going to be used. Consult your dealer. Modes 2/3 ECUECU AJ- RB 65 ∫1 Camera recorder Monitor BNC cable BNC cable6-pin cable To VIDEO IN...
Page 7
English E-6 Parts and their functions ENABLE WARNINGREW STOPFFECUECU AJ-START/STOP PLAYREC CHK ON OFFON OFF AW B ABB SHUTTER KNEE POINT KNEE SLOPE GAMMA DETAILSET UP PAINTING ENABLE IRISGAIN AUTO MANUAL GAINM.PEDCHECKFILTER RB BLACK W.BAL CAMAUTO KNEEONPRSTA BUP OFF ON OFF ON S.S. ( PUSH)OFFDOWN BARS GAIN S.V100( 60)120 250 500 1000 2000 65 ∫1 I 1 2 3 4 5 6 8 9 : ; 7 < = > ? @ A B C D E F G H J K L M N O P V T R Control panel VTR ENABLE switch This enables the VTR operations 2through 7to be performed on...
Page 8
E-7 Parts and their functions W.BAL switch PRST : Set to this position if there is no time to adjust the white balance. The 3200K white balance value is stored in the memory as the presetting. A or B : When the =AWB / ABB switch is set to the AWB position, the white balance is automatically adjusted, and the value adjusted is stored in memory A or memory B. The white balance value corresponding to the FILTER control position can also be stored in the memory...
Page 9
English E-8 Parts and their functions CPAINTING ENABLE switch This is used to enable the PAINTING GAIN and BLACK VR controls. BPAINTING GAIN VRs R GAIN and B GAIN controls KINDICATOR This lights when a lens extender is used. LM.PED VR This is used to set the master pedestal. MNumber display LED The iris value and the gain or filter positions are displayed on this LED. Normally, the iris value is shown but when the gain value or filter position has been changed, the...
Page 10
E-9 Parts and their functions 12 1CAM/BS connector This is used to connect the unit with the camera recorder or AJ-BS900P. 2VIDEO OUT connector The video signals with characters added are output to this connector. Connector area