Panasonic Digital Camera Dmc L10 Operating Instructions

							Menu Settings
111VQT1G28
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P108)
This mode allows you to automatically 
display pictures vertically if they were 
recorded holding the camera vertically or 
rotate pictures manually in 90° steps.
∫Rotate display (The picture is 
automatically rotated and displayed.)
1Press 4 to select [ON] and then 
press [MENU/SET].
The pictures are displayed without 
being rotated when you select [OFF].
2Press [MENU/SET] to close the 
menu.
Pictures recorded holding the camera 
vertically are automatically displayed 
vertically.
∫Rotate
(The picture is rotated manually.)
1Press 2/1 to select the picture 
and then press 4.
The [ROTATE] function is disabled 
when [ROTATE DISP.] is set to [OFF].
Protected pictures cannot be rotated.
2Press 3/4 to select the direction 
to rotate the picture and then 
press [MENU/SET].
3Press [MENU/SET] twice to close 
the menu.
∫Example
When rotating clockwise ( )
Original
picture
[ROTATE DISP.]/[ROTATE]
To display the picture rotated
MENU/SET
MENU/SET
The picture rotates clockwise in 
steps of 90o.
The picture rotates 
counter-clockwise in steps of 90o.
MENU/SET
VQT1G28ENG_L10KP.book  111 ページ  ２００７年９月６日　木曜日　午前９時２９分 
						

							Menu Settings
112VQT1G28
 When [ROTATE DISP.] is set to [ON], 
pictures recorded holding the camera 
vertically are played back vertically 
(rotated).
(You can only use this when using a lens 
that supports the direction detection 
function. (P13))
 If you take pictures when aiming the 
camera up or down, it may not be possible 
to display the pictures vertically. (P35)
 The picture may be slightly blurred when 
the camera is connected to the TV with 
the video cable (supplied) and played 
back vertically.
 When you play back pictures on a PC, 
they cannot be displayed in the rotated 
direction unless the OS or software is 
compatible with Exif. Exif is a file format 
for still pictures which allows recording 
information etc. to be added. It was 
established by “JEITA (Japan Electronics 
and Information Technology Industries 
Association)”.
 Rotated pictures are displayed rotated 
when they are played back in review 
playback and playback zoom however are 
displayed without being rotated when they 
are played back in multi playback.
 It may not be possible to rotate pictures 
that have been recorded with other 
equipment.Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P108)
DPOF “Digital Print Order Format” is a 
system that allows the user to select which 
pictures to print, how many copies of each 
picture to print and whether or not to print 
the recording date on the pictures when 
using a DPOF compatible photo printer or 
photo printing store. For details, ask at your 
photo printing store.
For more information visit:
http://panasonic.jp/dc/dpof_110/
white_e.htm
Press 3/4 to select [SINGLE], 
[MULTI] or [CANCEL] and then 
press [MENU/SET].
You cannot select [CANCEL] if there 
are no prints that have been set in the 
DPOF print settings.
∫Single setting
1Press 2/1 to select the picture to 
print and then press 3/4 to set 
the number of prints.
The number of prints icon [ ] A 
appears.
[DPOF PRINT]
Setting the picture to print and the 
number of prints
MENU/SET
MENU/SET
A
VQT1G28ENG_L10KP.book  112 ページ  ２００７年９月６日　木曜日　午前９時２９分 
						

							Menu Settings
113VQT1G28
The number of prints can be set from 0 
to 999. The DPOF print setting is 
canceled when the number of prints is 
set to [0].
2Press [MENU/SET] twice to close 
the menu.
∫Multi setting
1Press 2/1 to select the picture to 
print and then press 3/4 to set 
the number of prints.
The number of prints icon [ ] B 
appears.
Repeat the above procedure. (You 
cannot set all the pictures at one time.)
The number of prints can be set from 0 
to 999. The DPOF print setting is 
canceled when the number of prints is 
set to [0].
2Press [MENU/SET] twice to close 
the menu.
∫To cancel all settings
1Press 3 to select [YES] and then 
press [MENU/SET].
2Press [MENU/SET] to close the 
menu.
∫To print the date
After setting the number of prints, set/
cancel printing with the recording date by 
pressing [DISPLAY].
 The date print icon [ ] C appears.
 When you go to a photo printing store for 
digital printing, be sure to order the 
printing of the date additionally if required.
 Depending on the photo printing store or 
the printer, the date may not be printed 
even if you set to print the date. For further 
information, ask at your photo printing 
store or refer to the operating instructions 
for the printer.
 DPOF is an abbreviation of “Digital Print 
Order Format”. This feature allows you to 
write print information to media and then 
use the information on a DPOF-compliant 
system.
 DPOF print setting is a convenient 
function when printing pictures with a 
printer that supports PictBridge. The date 
printing setting on the printer may take 
priority over the date printing setting on 
the camera. Check the date printing 
setting on the printer also. (P120)
Some DPOF information set by other 
equipment cannot be used. In such cases, 
delete all of the DPOF information and 
then set it again with this camera.
 If the file is not based on the DCF 
standard, the DPOF print setting cannot 
be set. DCF is an abbreviation of “Design 
rule for Camera File system”, stipulated by 
“JEITA (Japan Electronics and Information 
Technology Industries Association)”.
Pictures that were taken with the 
[QUALITY] set to [RAW] cannot be printed 
using DPOF print.
B
MENU/SET
C
DATE
VQT1G28ENG_L10KP.book  113 ページ  ２００７年９月６日　木曜日　午前９時２９分 
						

							Menu Settings
114VQT1G28
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P108)
You can set protection for pictures you do 
not want to be deleted by mistake.
Press 3/4 to select [SINGLE], 
[MULTI] or [CANCEL] and then 
press [MENU/SET].
∫Single setting
1Press 2/1 to select the picture 
and then press 4 to SET/
CANCEL.
2Press [MENU/SET] twice to close 
the menu.
∫Multi setting/To cancel all settings
Perform the same operation as in 
“[DPOF PRINT]”. (P112 to 113)
 The protect setting may not be effective 
on other equipment.
 If you want to delete protected pictures, 
cancel their protection.
 Even if you protect pictures on a card, 
they will be deleted if the card is 
formatted. (P32)
 Even if you do not protect pictures on an 
SD Memory Card or an SDHC Memory 
card, they cannot be deleted when the 
card’s Write Protect switch B is slid to the 
[LOCK] side.
 Protected pictures cannot be rotated.[PROTECT]
Preventing accidental erasure of 
pictures
[SET]The protect icon [ ] A 
appears.
[CANCEL]The protect icon [ ] A 
disappears.
MENU/SET
MENU/SET
A
2
B
VQT1G28ENG_L10KP.book  114 ページ  ２００７年９月６日　木曜日　午前９時２９分 
						

							Menu Settings
115VQT1G28
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P108)
You can reduce the size of a recorded 
picture.
1Press 2/1 to select the picture 
and then press 4.
2Press 2/1 to select the size and 
then press 4.
Sizes smaller than the recorded picture 
are displayed.
The message [DELETE ORIGINAL 
PICTURE?] appears.
3Press 3/4 to select [YES] or 
[NO] and then press [MENU/SET].
The picture is overwritten when you 
select [YES]. Resized pictures cannot 
be restored when they are overwritten.
A resized picture is newly created when 
you select [NO].
If the original picture is protected, you 
cannot overwrite it. Select [NO] and 
newly create a resized picture.
4Press [MENU/SET] twice to close 
the menu.
 The following pictures cannot be resized.
– Pictures recorded when the quality is 
set to [RAW], [RAWiFine] or 
[RAWiStandard]
 When you want to reduce the size of a 
picture to attach it to an e-mail or upload it 
to a website, use the software 
“PHOTOfunSTUDIO-viewer-” on the 
CD-ROM (supplied) to change the size.
 It may not be possible to resize pictures 
recorded with other equipment.
[RESIZE]
Making the picture size smaller
Aspect RatioPicture Size
/
/
/
MENU/SET
MENU/SET
Aspect RatioPicture Size
VQT1G28ENG_L10KP.book  115 ページ  ２００７年９月６日　木曜日　午前９時２９分 
						

							Menu Settings
116VQT1G28
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P108)
You can enlarge and then clip the important 
part of the recorded picture.
1Press 2/1 to select the picture 
and then press 4.
2Enlarge or decrease the parts to 
be trimmed with the rear dial.
3Press 3/4/2/1 to move the 
position of the part to be trimmed.
4Press shutter button.
The message [DELETE ORIGINAL 
PICTURE?] appears.
5Press 3/4 to select [YES] or 
[NO] and then press [MENU/SET].
The picture is overwritten when you 
select [YES]. The trimmed pictures 
cannot be restored when they are 
overwritten.
A trimmed picture is newly created 
when you select [NO].
When the original picture is protected, 
you cannot overwrite it. Select [NO] and 
newly create a trimmed picture.
6Press [MENU/SET] twice to close 
the menu.
 The following pictures cannot be trimmed.
– Pictures recorded when the quality is set 
to [RAW], [RAWiFine] or 
[RAWiStandard]
 Depending on the cut size, the picture size 
of the trimmed picture may become 
smaller than that of the original picture.
 The picture quality of the trimmed picture 
will deteriorate.
 It may not be possible to trim pictures 
recorded with other equipment.
[TRIMMING]
Enlarging a picture and trimming it
MENU/SET
MENU/SET
VQT1G28ENG_L10KP.book  116 ページ  ２００７年９月６日　木曜日　午前９時２９分 
						

							Menu Settings
117VQT1G28
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P108)
You can convert pictures taken with a 
[ ] aspect ratio to a [ ] or a [ ] 
aspect ratio for printing.
1Press 3/4 to select [ ] or 
[ ] and then press [MENU/SET].
2Press 2/1 to select a picture and 
then press 4.
If you select and set a picture with an 
aspect ratio other than [ ], the 
message [CANNOT BE SET ON THIS 
PICTURE] is displayed on the screen.
3Press 2/1 to determine the 
horizontal position and then 
press the shutter button to set.
Use 3/4 to set the frame position for 
pictures rotated vertically.The message [DELETE ORIGINAL 
PICTURE?] appears.
4Press 3/4 to select [YES] or 
[NO] and then press [MENU/SET].
The picture is overwritten when you 
select [YES]. If you convert the aspect 
ratio of a picture and then overwrite it, 
you cannot restore it.
A picture with the converted aspect 
ratio is newly created when you select 
[NO].
When the original picture is protected, 
you cannot overwrite it. Select [NO] and 
newly create a picture with the 
converted aspect ratio.
5Press [MENU/SET] twice to close 
the menu.
 The following pictures cannot be 
converted.
– Pictures recorded when the quality is set 
to [RAW], [RAWiFine] or 
[RAWiStandard]
 Files that do not conform to the DCF 
standard cannot be converted. DCF is an 
abbreviation of “Design rule for Camera 
File system”, stipulated by JEITA “Japan 
Electronics and Information Technology 
Industries Association”.
 You may not be able to convert pictures 
taken on other equipment.
[ASPECT CONV.]
Changing the aspect ratio of a 16:9 
picture
MENU/SET
MENU/SET
MENU/SET
VQT1G28ENG_L10KP.book  117 ページ  ２００７年９月６日　木曜日　午前９時２９分 
						

							Connecting to other equipment
118VQT1G28
Connecting to other equipment
Connecting to a PC
You can acquire recorded pictures to a PC 
by connecting the camera and the PC.
The software [LUMIX Simple Viewer] or 
[PHOTOfunSTUDIO-viewer-] 
(for Windows
®) on the CD-ROM (supplied) 
allows you to easily acquire pictures 
recorded with the camera to a PC, print 
them and send them by e-mail.
If you use “Windows 98/98SE”, install 
the USB driver and then connect it to 
the computer.
Read the separate operating instructions 
for the supplied software for more 
information about the software in the 
CD-ROM (supplied) and how to install it.
AUSB connection cable (supplied)
BDC cable (DMW-DCC1; optional)
CThis message appears during data 
transfer. Use a sufficiently charged battery (P18) or 
the AC adaptor (P128).
 Turn the camera off and then insert or 
remove the cable for the AC adaptor  
(P128).
1Turn on the camera and the PC.
2Connect the camera to a PC via 
the USB connection cable 
A 
(supplied).
Connect the USB connection cable with 
the [ ] mark facing the [2] mark on 
the [DIGITAL] socket.
Hold the USB connection cable at D 
and insert straight in or take straight 
out. (If you forcibly insert the USB 
connection cable at a slant or upside 
down you can deform the connection 
terminals and damage the camera or 
the connected equipment.)
3Press 3 to select [PC] and then 
press [MENU/SET].
If you set [USB MODE] in the [SETUP] 
menu to [PC] in advance, it is not 
necessary to set this every time you 
connect to a PC. (P30)
If you set [USB MODE] to 
[PictBridge (PTP)] and then connect the 
camera to the PC, messages may 
appear on the screen of the PC.
Select [CANCEL] to close the 
messages and disconnect the camera 
from the PC. Set [USB MODE] to [PC] 
again.
ACCESS
D
C
B
A
USB MODE
PictBridge(PTP)
SELECTSETMENU
PC
PLEASE SELECT 
THE USB MODE
MENU/SET
VQT1G28ENG_L10KP.book  118 ページ  ２００７年９月６日　木曜日　午前９時２９分 
						

							Connecting to other equipment
119VQT1G28
[Windows]
The drive appears in the [My Computer] 
folder.
 If you are connecting the camera to a PC 
for the first time, the required driver is 
installed automatically so that the camera 
can be recognized by “Windows Plug and 
Play”. The drive then appears on the 
[My Computer] folder.
[Macintosh]
The drive is displayed on the screen.
 The drive is displayed as [NO_NAME] or 
[Untitled].
∫Folder Composition
Folders are displayed as shown in the 
following illustration.The items in each folder are as follows.
 The data for up to 999 pictures recorded 
by the camera can be included in 1 folder. 
If the number of pictures exceeds 999, 
another folder is created.
 To reset the file number or the folder 
number, select [NO.RESET] in the 
[SETUP] menu. (P29)
∫Conditions under which a different 
folder number is used
The picture is not recorded in the same 
folder as the previously recorded picture in 
the following cases. It is recorded in a folder 
with a new number.
1When the folder just recorded to 
contains a picture file with the number 
999 in it (example: P1000999.JPG).
2When the card just recorded to 
contains, for example, a folder with the 
number 100 [100_PANA] in it and that 
card is removed and replaced with a 
card that has a folder with the number 
100 in it recorded by a camera from a 
different maker (100XXXXX, with 
XXXXX being the name of the maker) 
and then a picture is recorded.
3When recording after selecting 
[NO.RESET] (P29) from the [SETUP] 
menu. (Pictures will be recorded to a 
new folder with a number sequential to 
the folder recorded to immediately 
before. By using [NO.RESET] on a card 
that does not contain folders or 
pictures, such as one just formatted, 
the folder number can be reset to 100.) 1Folder number
2Color space P: sRGB
_: AdobeRGB
3File number
4JPG: Pictures
RAW: Pictures in RAW files
MISC: DPOF print
Favo r i te
100_PANA
101_PANA
999_PANA DCIM
MISC
P1000001.JPG
P1000002.JPG
P1000999.JPG
100_PANA1
34
2
≥
Card
[DCIM]Folders from [100_PANA] to 
[999_PANA]
[100_PANA] 
to 
[999_PANA]Pictures/RAW files
[MISC]Files on which the DPOF 
print settings are recorded, 
Favo r it e s
VQT1G28ENG_L10KP.book  119 ページ  ２００７年９月６日　木曜日　午前９時２９分 
						

							Connecting to other equipment
120VQT1G28
∫PictBridge (PTP) setting
Even if you set [USB MODE] to 
[PictBridge (PTP)], you can connect to your 
PC if the OS is “Windows XP”, 
“Windows Vista” or “Mac OS X”.
 Pictures can only be read on the camera. 
They cannot be written to a card or 
deleted.
 When there are 1000 or more pictures on 
a card, the pictures may not be imported.
Do not use any other USB connection 
cables except the supplied one.
 Do not disconnect the USB connection 
cable while [ACCESS] is displayed.
 If battery power is exhausted while the 
camera and the PC are communicating, 
the recorded data may be damaged. Use 
a battery with sufficient battery power 
(P18) or the AC adaptor (P128).
 If the remaining battery power becomes 
low while the camera and the PC are 
communicating, the status indicator blinks 
and the alarm beeps. In this case, stop 
the communication at once on the PC.
 When connecting the camera to a 
“Windows 2000” OS PC with the USB 
connection cable, do not replace the 
card while the camera and the PC are 
connected. The information on the card 
may be damaged. Disconnect the USB 
connection cable before replacing the 
card.
 Pictures edited or rotated with a PC may 
be displayed in black in playback mode 
(P48), multi playback (P52) and calendar 
playback (P53).
 For information about this, refer to the 
separate operating instructions for PC 
connection.
 Read the operating instructions for the 
PC.
Printing the Pictures
By connecting the camera directly to a 
printer supporting PictBridge via the USB 
connection cable (supplied), you can select 
the pictures to print and start printing on the 
camera’s screen.
Set print settings such as the print quality 
on the printer beforehand. (Read the printer 
operating instructions.)
AUSB connection cable (supplied)
BDC cable (DMW-DCC1; optional)
 It may take time to print the pictures so 
use a battery with sufficient battery power 
(P18) or the AC Adaptor (P128) when you 
connect to a printer.
 Turn the camera off and then insert or 
remove the cable for the AC Adaptor 
(P128).
C
A
B
VQT1G28ENG_L10KP.book  120 ページ  ２００７年９月６日　木曜日　午前９時２９分