Panasonic Digital Camera Dmc Ts3 Owners Manual

							11(ENG) VQT3L22
(Important) About the Waterproof/
Dustproof and Anti-shock Performance of 
the Camera
This does not guarantee no destruction, no malfunction, or waterproofing in 
all conditions.
¢1 This means that the camera can be used underwater for specified time in 
specified pressure in accordance with the handling method established by 
Panasonic.
¢ 2 “MIL-STD 810F Method 516.5-Shock” is the test method standard of the U.S. 
Defense Department, which specifies performing drop tests from a height of 
122 cm (4.0 feet), at 26 orientations (8 corners, 12 ridges, 6 faces) using 5 
sets of devices, and passing the 26 orientation drops within 5 devices. (If 
failure occurs during the test, a new set is used to pass the drop orientation 
test within a total of 5 devices)
Panasonic’s test method is based on the above “MIL-STD 810F Method 
516.5-Shock”. However, the drop height was changed from 122 cm (4.0 feet) 
to 200 cm (6.6 feet) dropping onto 3 cm (0.10 feet) thick plyboard. This drop 
test was passed.
(Disregarding appearance change such as loss of paint or distortion of the 
part where drop impact is applied.)
Waterproof/Dustproof Performance
This camera’s waterproof/dustproof rating complies with the “IPX8” and 
“IP6X” ratings. Provided the care and maintenance guidelines described 
in this document are strictly followed, this camera can operate 
underwater, to a depth not exceeding 12 m (40 feet) for a time not 
exceeding 60 minutes. ( ¢1)
Anti-shock Performance This camera also complies with “MIL-STD 810F Method 516.5-Shock”. 
The camera has cleared a drop test from a height of 2 m (6.6 feet) onto 
3 cm (0.10 feet) thick plywood. In most cases this camera should not 
sustain any damage if dropped from a height not exceeding 2 m 
(6.6 feet). ( ¢2)
DMC-TS3P-VQT3L22_eng.book  11 ページ  ２０１１年１月２１日　金曜日　午後７時４０分 
						

							VQT3L22 (ENG)12
∫Handling of the camera
•Waterproofing is not guaranteed if the unit is subject to an impact as a result of 
being hit or dropped etc. If an impact to the camera occurs, it should be 
inspected (subject to a fee) by a Panasonic’s Service Center to verify that the 
waterproofing is still effective.
•When the camera is splashed with detergent, soap, hot spring, bath additive, 
sun oil, sun screen, chemical, etc., wipe it off immediately.
•Waterproof function of the camera is for sea water and fresh water only.•Any malfunction caused by customer mi suse, or mishandling will not be covered 
by the warranty.
•The inside of this unit is not waterproof. Water leakage will cause malfunction.•Supplied accessories are not waterproof (excluding strap).•Card and battery are not waterproof. Do not handle with a wet hand. Also, do not 
insert wet card or battery into the camera.
•Do not leave the camera for a long period of time in places where temperature is 
very low (at ski resorts or at high altitude etc.) or very high [above 40 oC 
(104 °F)], inside a car under strong sunlight, close to a heater, on the beach, etc. 
Waterproof performance may be degraded.
∫ About the [Precautions] demonstration display
•[Precautions] is displayed when the power is turned on for the first time after 
purchase, with the side door completely closed.
•Please check beforehand to maintain the waterproof performance.
1Press  2 to select [Yes], and press [MENU/SET].
•It will automatically skip to the clock setting screen if [No] is selected before 
it starts.
2Press  2/1 to select the picture.
•
It can be forcefully ended by pressing [MENU/SET].•When it is forcefully ended while checking by turning the power off or 
pressing [MENU/SET], [Precautions] is displayed every time the power is 
turned on.
3After the final screen (12/12), press [MENU/SET] to finish.
•When [MENU/SET] is pressed after the final screen (12/12), [Precautions] 
is not displayed from the next time the power is turned on.
•This can also be viewed from [Precautions] in the [Setup] menu.
2: Return to the previous screen
1: View the next screen
DMC-TS3P-VQT3L22_eng.book  12 ページ  ２０１１年１月２１日　金曜日　午後７時４０分 
						

							13(ENG) VQT3L22
1Check that there are no foreign objects on the inner side of the side door.•If there is any foreign object, such as lint, hair, sand, etc., on the 
surrounding area, water will leak within a few seconds causing malfunction.
•Wipe it off with a dry soft cloth if there is any liquid.
It may cause water leaks and malfunction if you use the camera with liquid adhered.
•If there is any foreign material, remove with supplied brush.•Be extremely careful to remove the small pieces of sand etc. that may have 
adhere to the sides and corners of the rubber seal.
•Remove large foreign objects, wet sand, etc., using the shorter (harder) 
side of the brush.A Brush (supplied)
B Side door
2Check for cracks and deformation of the rubber seal on the side door.•The integrity of the rubber seals may decrease after about 1 year, with use 
and age. To avoid permanently damaging the camera the seals should be 
replaced once each year. Please contact Panasonic’s Service Center for 
related costs and other information.
3Close the side door securely.
•Lock the [LOCK] switch securely until the red part is no longer visible.•To prevent water seeping into the camera, be careful not to trap foreign 
objects such as liquids, sand, hair or dust etc.
Check before using underwater
Do not open or close the side door in places with sand and dust, close to 
water, or with wet hands. Sand or dust adhering may cause water leaks.
C
:Red part
D
:[LOCK] switch (gray part)
E
:Released state
F
:Locked state




0í0ð0ä0ì
0í0ð0ä0ì
0í0ð0ä0ì


DMC-TS3P-VQT3L22_eng.book  13 ページ  ２０１１年１月２１日　金曜日　午後７時４０分 
						

							VQT3L22 (ENG)14
•Use the camera underwater at a depth of up to 12 m (40 feet) with the water 
temperature between 0oC and 40 oC (32 oF to 104 °F).
•Do not use for scuba diving (Aqualung).•Do not use the camera at a depth of over 12 m (40 feet).•Do not use it in the hot water over 40 oC (104 °F) (in the bath or hot spring).•Do not use the camera underwater for longer than 60 minutes continuously.•Do not open or close the side door.•Do not apply shock to the camera underwater. (Waterproof performance may not 
be maintained, and there is a chance of a water leak.)
•Do not dive into the water holding the camera. Do not use the camera in a 
location where the water will splash strongly, such as near rapids or waterfalls. 
(Strong water pressure may be applied, and it may cause malfunction.)
•The camera will sink in the water. Take  care not to drop the camera and lose it 
underwater by securely placing the strap around your wrist or similar measure.
1Rinse with water with the side door 
closed.
•
After use at the seaside or underwater, 
soak the unit in fresh water pooled in a 
shallow container for 10 minutes or less.
•If the zoom button or camera [OFF/ON] 
button do not move smoothly, it may be 
caused by an adhesion of foreign 
objects. Using in such a state may cause 
malfunctions, such as locking up, so wash off any foreign objects by 
shaking the camera in fresh water.
•Bubbles may come out of the drainage hole when you immerse the camera 
in water, but this is not a malfunction.
Using the camera underwater
Caring of the camera after using it underwater
Do not open or close the side door until the sand and dust is removed by 
rinsing the camera with water.
Make sure to clean the camera after using it.
•Thoroughly wipe off any water droplets, sand, and saline matter on your hands, 
body, hair, etc.
•It is recommended to clean the camera indoors, avoiding places where water 
spray or sand may fall.
Do not leave the camera uncared for more than 60 minutes after using it 
underwater.
•Leaving the camera with foreign objects or saline matter on it may cause 
damage, discoloration, corrosion, unusual odour, or deterioration of the 
waterproof performance.
DMC-TS3P-VQT3L22_eng.book  14 ページ  ２０１１年１月２１日　金曜日　午後７時４０分 
						

							15(ENG) VQT3L22
2Drain water by holding the camera 
upside down and shaking it lightly a 
few times.
•
After using the camera at the seaside or 
under water, or after washing it, water 
will remain at the speaker site of the 
camera for a while and it may cause 
lower sound or sound distortion.
•Fasten the strap firmly to prevent the 
camera from dropping.
3Wipe off water drops on the camera 
with a dry soft cloth and dry the 
camera in a shaded area which is 
well ventilated.
•
Dry the camera by standing it on a dry 
cloth. This unit incorporates drain 
design, draining water in gaps in the 
camera [OFF/ON] button and zoom button etc.
•Do not dry the camera with hot air from dryer or similar. Waterproof 
performance will deteriorate due to deformation.
•Do not use chemicals such as benzine, thinner, alcohol, or cleanser, or 
soap or detergents.
4Confirm that there are no water droplets, open the side door, and 
wipe off any water droplets or sand left inside using a soft dry 
cloth.
•
Water droplets may adhere to the card or battery when the side door is 
opened without thoroughly drying. Also, water may accumulate in the gap 
around the card/battery compartment or the terminal connector. Be sure to 
wipe any water off with a soft dry cloth.
•The water droplets may seep into the camera when the side door is closed 
while it is still wet, causing condensation or failure.
DMC-TS3P-VQT3L22_eng.book  15 ページ  ２０１１年１月２１日　金曜日　午後７時４０分 
						

							VQT3L22 (ENG)16
Names of the Components
1Flash
2 Self-timer indicator/AF Assist Lamp/LED light
3Lens
4 LCD monitor
5 Speaker
6 Zoom button
7 Playback button
8 [MODE] button
9 [MENU/SET] button
10 [Q.MENU]/Delete/Cancel button
11 [DISP.] button
12 Cursor buttons A: 3/Exposure compensation
Auto Bracket
B:  4/Macro Mode
AF Tracking
C:  2/Self-timer
D:  1/Flash setting
In this Owner’s Manual, the cursor buttons are described as shown in 
the figure below or described with  3/4/2 /1.
e.g.: When you press the  4 (down) button
orPress  4213
456
111012
8
97
MENU/SET
MENU/SET
VQT3L22~Body1_eng.fm  16 ページ  ２０１１年１月２４日　月曜日　午前１０時４６分 
						

							17(ENG) VQT3L22
13 Motion picture button
14 Shutter button
15 Camera [OFF/ON] button
16 GPS antenna
17 Microphone
18 GPS status indicator
19 Tripod receptacle
20 [HDMI] socket
21 [AV OUT/DIGITAL] socket
22 Strap eyelet
•Be sure to attach the strap when using the 
camera to ensure that you will not drop it.
23 Release lever
24 [LOCK] switch
25 Side door
•When using an AC adaptor, ensure that 
the Panasonic DC coupler (DMW-DCC4; 
optional) and AC adaptor (DMW-AC5PP; 
optional) are used.
•Always use a genuine Panasonic AC 
adaptor (DMW-AC5PP; optional).
•It is recommended to use a fully charged 
battery or AC adaptor (DMW-AC5PP; 
optional) and DC coupler (DMW-DCC4; 
optional) when recording motion pictures.
•If while recording motion pictures using the 
AC adaptor and the power supply is cut off 
due to a power outage or if the AC adaptor 
is disconnected etc., the motion picture 
being recorded will not be recorded.
13141516
1817
19
0í0ð0ä0ì0â0÷0Á0ð0ö0õ0Á0Ð0Á0å0ê0è0ê0õ0â0í
20
21
0í0ð0ä0ì23
24
22
25
DMC-TS3P-VQT3L22_eng.book  17 ページ  ２０１１年１月２１日　金曜日　午後７時４０分 
						

							VQT3L22 (ENG)18
Charging the Battery
∫About batteries that you can use with this unitThe battery that can be used with this unit is DMW-BCF10PP.
•Use the dedicated charger and battery.
•The battery is not charged when the camera is shipped. Charge the battery 
before use.
•Charge the battery with the charger indoors.It has been found that counterfeit battery packs which look very similar 
to the genuine product are made available to purchase in some markets. 
Some of these battery packs are not adequately protected with internal 
protection to meet the requirements of appropriate safety standards. 
There is a possibility that these battery packs may lead to fire or 
explosion. Please be advised that we are not liable for any accident or 
failure occurring as a result of use of a counterfeit battery pack. To 
ensure that safe products are used we would recommend that a genuine 
Panasonic battery pack is used.
Charging
Attach the battery paying 
attention to the direction of the 
battery.
Connect the charger to the 
electrical outlet.
•Disconnect the charger from the 
electrical socket and detach the battery 
after charging is completed.90
DMC-TS3P-VQT3L22_eng.book  18 ページ  ２０１１年１月２１日　金曜日　午後７時４０分 
						

							19(ENG) VQT3L22
∫ About the [CHARGE] indicatorThe [CHARGE] indicator turns on:
The [CHARGE] indicator  A is turned on during charging.
The [CHARGE] indicator turns off:
The [CHARGE] indicator  A will turn off once the charging has completed without 
any problem.
•When the [CHARGE] indicator flashes–The battery temperature is too high or too low. It is recommended to charge 
the battery again in an ambient temperature of between 10 oC to 30 oC (50 oF 
to 86 oF).
–The terminals of the charger or the battery are dirty. In this case, wipe off the 
dirt with a dry cloth. 
∫ Charging time
Recording conditions by CIPA standard•CIPA is an abbreviation of [Camera & Imaging Products Association].•Normal Picture Mode•Temperature: 23 oC (73.4 oF)/Humidity: 50%RH when LCD monitor is on.•Using a Panasonic SD Memory Card (32 MB).•Using the supplied battery.•Starting recording 30 seconds after the camera is turned on. (When the Optical 
Image Stabilizer function is set to [ON].)
•Recording once every 30 seconds  with full flash every second recording.•Changing the zoom magnification from Te le to Wide or vice versa in every 
recording.
•Turning the camera off every 10 recordings and leaving it until the temperature 
of the battery decreases.
•Not using the GPS function.
Charging time Approx. 130 min
Approximate operating time and number of recordable pictures
Number of recordable 
pictures Approx. 310 pictures
Recording time
Approx. 155 min
Playback timeApprox. 300 min
DMC-TS3P-VQT3L22_eng.book  19 ページ  ２０１１年１月２１日　金曜日　午後７時４０分 
						

							VQT3L22 (ENG)20
About the Built-in Memory/the Card
•You can copy the recorded pictures to a card.•Memory size: Approx. 19 MB•The access time for the built-in memory may be longer than the access time for a card.
The following cards which conform to the SD video standard can be used with this unit.
(These cards are indicated as  card in the text.)
¢ SD Speed Class is the speed standard regarding continuous writing. Check 
via the label on the card, etc.
•Please confirm the latest information on the following website.
http://panasonic.jp/support/global/cs/dsc/
(This Site is English only.)
Note
•Keep the Memory Card out of reach of children to prevent swallowing.
Built-in Memory
Card
Type of card which 
can be used with this 
unitRemarks
SD Memory Card 
(8 MB to 2 GB)•Use a card with SD Speed Class¢ with “Class 4” 
or higher when recording motion pictures in 
[AVCHD]. Also, use a card with SD Speed Class 
with “Class 6” or higher when recording motion 
pictures in [Motion JPEG].
•SDHC Memory Card can be used with SDHC 
Memory Card or SDXC Memory Card compatible 
equipment.
•SDXC Memory Card can only be used with SDXC 
Memory Card compatible equipment.
•Check that the PC and other equipment are 
compatible when using the SDXC Memory Cards.
http://panasonic.net/avc/sdcard/information/
SDXC.html•Only the cards with capacity listed left can be used.
SDHC Memory Card 
(4 GB to 32 GB)
SDXC Memory Card 
(48 GB, 64 GB)
e.g.:
DMC-TS3P-VQT3L22_eng.book  20 ページ  ２０１１年１月２１日　金曜日　午後７時４０分