Panasonic Digital Catv Terminal Tzpcd3000 Operating Instructions

Digital CATV Terminal
Operating Instructions
Model No. 
TZ-PCD3000
For assistance, please call : your local cable operator
Before connecting, operating or adjusting this product, please read these instructions completely.
Save this manual for future reference.
TQB2AA0489 

The Class ll insulation symbol(square within a square)indicates that
this product has been evaluated and tested to comply with Class ll
insulation requirements.
WARNING: To prevent damage which may result in fire or shock hazard,
         do not expose this appliance to rain or moisture.
Note To CATV System Installer
This reminder is provided to call the CATV system installer’s attention to article 820-40
of the National Electric Code that provides guidelines for proper grounding and in par-
ticular...

Cables are available from your dealer or electronic supply house.
Before you purchase any cables, be sure you know what type of output and input con-
nectors your various components require.
Also determine the length of cable you’ll need.
AC Power Supply CordFCC  INFORMATION
To prevent electric shock, match wide blade of plug to wide slot of AC
outlet and fully insert. Do not use this (polarized) plug with a recep-
tacle or other outlet unless the blade can be fully inserted to prevent
blade exposure....

For assistance, please call : your local cable operator
Front and Rear View of the Digital CATV Terminal
5
123
4 Dear Panasonic Customer
Welcome to the Panasonic Family of customers. We hope that you have many years of enjoyment from your new Digital CATV
Terminal. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain
them for future reference.
Front Panel
10 78
954
106
7
8
9
Remote control
signal present
indicator(LED)
Flashes when an...

5 12
34
Rear Panel
10 6
78
95
1
2
3
4106
7
8
9
11
12 1112
CABLE IN
CABLE OUT
DIGITAL AUDIO
COAX OUT
AC Power Input AUDIO OUT
VIDEO OUT
S-VIDEO OUT
DIGITAL AUDIO
OPT OUT
IR  BLASTER
SERIAL portAC Switched
Outlet
Use to connect Cable Signal input  from Cable
Service Provider.
Use to connect the Digital CATV Terminal out-
put to your TV or VCR.
The COAXIAL S/PDIF connector is a digital out-
put connection that carries Dolby Digital  (up to
5.1ch) audio or PCM audio.
Use to connect a peripheral equipment to...

Digital CATV Terminal connection to stereo TV and stereo VCRFollow this diagram when connecting the Digital CATV Terminal to a stereo TV.
Procedure1 Connect S-VIDEO Cable from the S-VIDEO output jack on the Digital CATV Terminal to the S-VIDEO input jack on the TV or VCR.
     Note: Connect either the S-VIDEO or video input/output as shown above.
   S-VIDEO will provide better picture quallity.
2 Connect audio cables from the left and right audio output jacks on the Digital CATV Terminal to the left and...

Digital CATV Terminal connection to TV and VCRFollow this diagram when connecting the Digital CATV Terminal to a TV and VCR.
ProcedureNote:Connect the CABLE OUT jack of the Digital CATV Terminal to the ANT IN jack of the VCR, and connect the ANT
OUT jack of the VCR to the ANT IN jack of the TV using 75    shielded cable.Additional equipment and cables shown are not supplied with this set.
USB
SERIAL  DIGITAL
AUDIO COAX
OUT   IRBLASTER CABLE IN
VIDEO VIDEO
R-AUDIO-L
OUT2
OUT1
S-VIDEOSWITCHED AC OUT...

Troubleshooting
Check that the batteries are installed with the correct polarities (+and -).
The batteries are depleted: Replace them with new ones.
Point the remote control unit at the remote control sensor and operate.
Operate the remote control unit at a distance of not more than 23 feet (7 meters) from the remote control sensor.
Remove any obstacles between the remote control unit and remote control sensor.
Make sure the remote control is in the proper component mode (i.e. CABLE, TV,VCR,AUDIO)....