Panasonic Digital Disk Recorder Wj Hd220 Operating Instructions

41
HTTP Port (HTTP PORT)
Set an HTTP port number.
The default is 80.
Available port numbers:From 00000 to 65535, except
the well-known port numbers assigned by IANA
(Internet Assigned Numbers Authority)
Dynamic Host Configuration Protocol
(DHCP)
Dynamic Host Configuration Protocol is enabled or dis-
abled.
The default is OFF.
Note:When ON is selected, you cannot enter the IP
address, netmask, or gateway. The host gives these
parameters.
The given parameters will be displayed after getting
the IP...

42
Multiscreen Sequence Setup (MULTI
SEQ SETUP)
Open the QUAD SEQ SETUP menu to program the
sequence steps for displaying quad-split and single input
images.
1. Move the cursor to the desired step using the [D] or
[C] button.
2. Select a camera number with the JogDial, and press
the JogDial.
The default camera number is identical to the step num-
ber.
Available cameras:From 1 to 8 individually, 4A(1-4), or
4B(5-8)
Note:The recorder will skip any step assigned –.
3. Select the duration for the step with...

43
1. Move the cursor to the desired camera using the [D] or
[C] button.
2. Select ON or OFF with the JogDial, and press the
JogDial.
The default is ON.
ON:Live image of the channel is displayed.
OFF:Blackout image is displayed.
3. Repeat steps 1 and 2 until all channels are pro-
grammed, or press the [SETUP/ESC] button to return to
the SWITCHER SETUP menu,
Notes: 
•Recording will be carried out regardless of this set-
ting.
•The recorded images of the channel will be played
back and displayed on the...

44
Language (LANGUAGE)
Language selection is available for display on the multi-
screen monitor and for HTML on the browser.
1. Move the cursor to LANGUAGE.
2. Select a language with the JogDial and press the
JogDial.
The default is ENGLISH.
Available languages:ENGLISH, FRENCH, GERMAN,
ITALIAN, SPANISH, RUSSIAN, CHINESE
Notes:
•When Russian or Chinese is selected, HTML will display
in the selected language, but the multiscreen monitor
will display in English. See the table below.
•The recorder will exit...

45
OPERATING PROCEDURES
Controlling Video Inputs &
Monitors
Operations on the front panel can control video inputs on
the spot monitor or multiscreen monitor.
On the Spot Monitor
Selecting the Spot Monitor
1. Press the [SPOT/MULTI] button to turn the LED in the
button on. The spot monitor is ready to be operated.
2. Follow the descriptions below for each monitoring mode
on the spot monitor.
Viewing a Single Live
A selected live image is displayed on the spot monitor until
a new input selection is...

46
On the Multiscreen Monitor
Selecting the Multiscreen Monitor
1. Press the [SPOT/MULTI] button to turn the LED in the
button off. The multiscreen monitor is ready to be oper-
ated.
2. Follow the descriptions below for each monitoring mode
on the multiscreen monitor.
Viewing a Single Live
The multiscreen monitor can display a single live spot
image. 
Operating procedures are the same as for On the Spot
Monitor except for selecting the multiscreen monitor.
Zooming a Single Live 
A single live or...

47
Connected Alarm Sensors
A maximum of eight sensors can be connected to the termi-
nals on the rear panel. Sensors may be installed in such
places as parking lots or reception desks where cars and
visitors come and go.
Built-in Motion Detector
The recorder detects motion for each of the eight video
inputs, based on certain changes in the video signal.
Built-in Video Loss Detector
The recorder detects any disconnection of the video inputs.
The images of the disconnected channel will not be record-...

48
Monitor Display
There are two monitoring modes, alarm associated (SPOT)
mode and alarm ignore (OFF) mode, depending on the
selection for MONITOR MODE in the ALARM SETUP menu.
Typical cases are described below for each setup.
Alarm Associated Mode
•The image of the alarmed input is displayed on the mul-
tiscreen monitor in single spot mode, interrupting what-
ever live, playback, single or multiple image previously
displayed. When a new alarm is received, the last acti-
vated input image will be...

49
Auto Reset
The activated alarm event is reset when the AUTO RESET
time has elapsed, or the lost video has been recovered. 
The ALARM indicator changes from blinking to a steady
light.
External Reset
The activated alarm event except video motion detection, is
reset when the recorder receives an external reset signal
from the connected device via the REMOTE/ALARM con-
nector on the rear panel.
The ALARM indicator changes from blinking to a steady
light.
Pressing REC STOP Button
Pressing the [REC...

50
Recording
Notes: 
•When SIMUL REC&PLAY (simultaneous recording and
playback) is set to OFF in the setup, any recording will
stop playback and start the recording. Playback is
unavailable while recording.
•When set to ON, recording is available while playing
back.
•The recording rate will degrade to 15 FPS while display-
ing a quad split screen.
Internal Timer Recording
When INT is set for TIMER in the WJ-HD220 MAIN menu,
the presets made in the internal timer will take effect.
Internal timer...