Home > Panasonic > Recording Equipment > Panasonic Digital Disk Recorders Wj Hd316 Operating Instructions

Panasonic Digital Disk Recorders Wj Hd316 Operating Instructions

Add to Favourites

Download as PDF Print this page Share this page

Have a look at the manual Panasonic Digital Disk Recorders Wj Hd316 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

Page 36 36
Any motion will be detected anywhere in the A, B, C, D
areas.
Note:In the ANY AREA mode, it is possible to set the
masking duration. When the masking duration is set,
motion will be ignored for a certain period (set duration
as the masking duration) in the same area. It is conve-
nient to set the masking duration to make the subject
period shorter in case it is necessary to search an
extended time range or searching through many
results.

It will be subject to be listed if an object moves within the...

Page 37 37
■ Searching for a marked point
and play from that point
(Marking search)
Display the recording time of recorded images with a
marked point in a list or a thumbnail and select the desired
recording time to play. Refer to page 24 for further informa-
tion about marking.
zPress the SEARCH button repeatedly until the
marking list window is displayed.
The result list of the marking search will be displayed on
monitor 2 and the VGA monitor.
Use the arrows button (
CD) to switch between displaying
the list...

Page 38 38
MONITOR LIVE IMAGES
It is possible to display live images on a single screen or a
multi-screen.
On a single sequential display (It is also possible that dis-
played images from cameras will be switched automatical-
ly)
■ Displaying Live Images on a
Single Screen
zPress the MONITOR1/MONITOR2 button to
select the monitor.
When monitor 1 is selected, the indicator will light.
When monitor 2 or the VGA monitor is selected, the indica-
tor will not light.
xPress a camera selection button
(1 - 16 for the...

Page 39 39
■ Displaying on a Multi-screen
It is possible to display images on a multi-screen (4, 7, 9,
10, 13, 16 for the WJ-HD316, 4, 7, 9 for the WJ-HD309).
zPress the MONITOR1/MONITOR2 button to
select the monitor.
When monitor 1 is selected, the indicator will light.
When monitor 2 is selected, the indicator will not light.
xPress the SHIFT button.
The SHIFT indicator will light.
cPress a camera selection button 1 - 6 (1 - 3 for
the WJ-HD309) to select a desired multi-
screen.
Camera selection button 1:...

Page 40 40
■ Sequential Display
Displayed images from cameras will be switched automati-
cally.
Camera images will be displayed sequentially according to
the settings performed in advance.
zPress the MONITOR1/MONITOR2 button to
select the monitor.
When monitor 1 is selected, the indicator will light.
When monitor 2 is selected, the indicator will not light.
xPress the SHIFT button.
The SHIFT indicator will light.
cPress the SEQ button.
The camera selection button respective to the displayed
image will light...

Page 41 41
CONTROL CAMERAS
When displaying live images, the following camera controls
are possible.
•Panning/tilting: Moves a camera horizontally/vertically.
•Zooming: Zooms in/out on images.
•Focus: Adjusts the focus.
•Iris: Adjusts the iris of the lens.
•Preset action: Moves a camera to the preset position
registered in advance.
•Auto function: Moves a camera with an auto function
set in advance.
Notes:
•Controlling cameras is possible only when displaying
images on a single screen.
•Depending on models of the...

Page 42 42
■ Iris
Adjusts the iris of the lens.
zPress the IRIS button.
The IRIS indicator will light.
xUse the arrows button (AB) to adjust the iris.
To reset the set iris, press the SET button.
■ Preset Action
Moves a camera to the preset position registered in
advance.
Important:
•When using a camera of the WV-CS650 (WV-CSR650)
series or the WV-CS600 (WV-CSR600) series, register
preset positions using the settings menu of the camera.
•When the monitor 1 is selected, it is impossible to regis-
ter preset...

Page 43 43
■ Move a camera to the preset
position
zPress the PRESET/AUTO button.
The PRESET/AUTO indicator will light and the PRESET/
AUTO PAN window will be displayed.
xPress a camera selection button
([1] - [10/0] for the WJ-HD316, [1] - [9], [0] for
the WJ-HD309) to select a desired preset posi-
tion.
Pressing the camera selection button [10/0] ([0] for the WJ-
HD309) moves a camera to the home position.
The jog dial can also be used to select a preset position
number by rotating it.
cSelect OK using the...

Page 44 44
Note:To move the camera to another registered preset
position, press the SET button after selecting a desired
preset position number in step 2. The PRESET/AUTO
PAN window will not close and it is possible to select
another preset number.
■ Auto Function (Auto Pan, etc)
Moves a camera with an auto function set in advance.
Important:
When the monitor 1 is selected, it is impossible to move
a camera with an auto function by performing the fol-
lowing steps.
In this case, perform the settings using the...

Page 45 Event Action
45
ABOUT THE EVENT FUNCTION
The event action will be performed when the following
events occur.
•
Motion detection:When motion is detected by the
motion detection function (see below), this is stated as
an event of motion detection.
•
Video Loss:When a video signal supply is stopped
because of a cable disconnection or malfunction of a
camera, this is stated as an event of video loss.
•
Terminal alarm:When a signal is supplied from an
external device such as a door sensor to the ALARM...

Page 46 46
■ Alarm Function
● Blinks the ALARM indicator on the front
panel
● Switches from the images displayed on
monitor 1 and monitor 2 to the images from
the location of the alarm occurrence (on a
single screen)
● Displays the event information in the alarm
display area on monitor 1 and the camera
title display area on monitor 2

● Sounds the buzzer
Contact a system administrator about sounding duration.
● Announces an event occurrence to the con-
nected system device (Alarm Output)
Sends a signal to the...

View all the pages

Add page 41 to Favourites

							41
CONTROL CAMERAS
When displaying live images, the following camera controls
are possible.
•Panning/tilting: Moves a camera horizontally/vertically.
•Zooming: Zooms in/out on images.
•Focus: Adjusts the focus.
•Iris: Adjusts the iris of the lens.
•Preset action: Moves a camera to the preset position
registered in advance.
•Auto function: Moves a camera with an auto function
set in advance.
Notes:
•Controlling cameras is possible only when displaying
images on a single screen.
•Depending on models of the connected cameras, it
may be impossible to control the camera or some func-
tions may not be available.
•Refer to page 126 for descriptions of how to display
and perform the settings with the settings menu of the
camera from this unit.
■ Panning/Tilting
Moves a camera horizontally/vertically.
zPress the PAN/TILT button.
The PAN/TILT indicator will light.
xUse the arrows button to adjust the vertical or
horizontal position.
Camera will move slowly by pressing the arrows button
while holding the SLOW button down.
■ Zoom
Zooms in/out on images. Depending on models of the con-
nected cameras, the image size for the respective zooming
level may be different. For further information, refer to the
operating instruction for the camera.
zPress the ZOOM/FOCUS button.
The ZOOM/FOCUS indicator will light.
xUse the arrows button (CD) to zoom in on or
out of the displayed image.
Press the arrows button downward (C) to zoom out and
upward (
D) to zoom in.
■ Focus
Adjusts the focus. The auto focus function is available.
zPress the FOCUS button.
The ZOOM/FOCUS indicator will light.
xUse the arrows button (AB) to adjust the
focus.
Auto focus is available by pressing the SET button.
R
2 R
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
zx
PAN/
TILT
R
2
R
1
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
zx
PAN/
TILT
R
2
R
1
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
zxx
PAN/
TILT

Add page 42 to Favourites

							42
■ Iris
Adjusts the iris of the lens.
zPress the IRIS button.
The IRIS indicator will light.
xUse the arrows button (AB) to adjust the iris.
To reset the set iris, press the SET button.
■ Preset Action
Moves a camera to the preset position registered in
advance.
Important:
•When using a camera of the WV-CS650 (WV-CSR650)
series or the WV-CS600 (WV-CSR600) series, register
preset positions using the settings menu of the camera.
•When the monitor 1 is selected, it is impossible to regis-
ter preset positions and move a camera to a preset
position by performing the following steps.
In this case, perform the settings using the setup menu
of camera.
● Register Preset Positions of Cameras
Up to 64 preset positions can be registered.
zPress the PAN/TILT button and move the cam-
era to a desired position to be registered as a
preset position.
xPress the SET button. The REGISTRATION
PRESET POSITION window will be displayed.
R
2 RMONITOR1
MONITOR21
5
9
13
2
6
10/0
14
3
7
11
15
4
8
12
16
SEQ SHIFT OSD
STOPPLAY PAUSEREC - REC STOP
ZOOM/
FOCUS
TEXTCOPYDISK SELECT
EL-ZOOM
MARK
LOGOUTIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWD
PAN/TILTSLOW
[WJ-HD316]
LOGOUT
R
2 R
MONITOR1
MONITOR21
4
7
2
5
8
0
3
6
9
TEXT SEQ SHIFT OSDZOOM/
FOCUSCOPYDISK SELECT
EL-ZOOM
MARKIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWDSTOPPLAY PAUSEREC - REC STOP
PAN/TILTSLOW
[WJ-HD309]
PAN/
TILT
PAN/
TILT
xz
xz
REGISTRATION PRESET POSITION
PRESET NUMBER
OK CANCEL32
R
2
R
1
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
zxx
PAN/
TILT

Add page 43 to Favourites

							43
■ Move a camera to the preset
position
zPress the PRESET/AUTO button.
The PRESET/AUTO indicator will light and the PRESET/
AUTO PAN window will be displayed.
xPress a camera selection button 
([1] - [10/0] for the WJ-HD316, [1] - [9], [0] for
the WJ-HD309) to select a desired preset posi-
tion.
Pressing the camera selection button [10/0] ([0] for the WJ-
HD309) moves a camera to the home position.
The jog dial can also be used to select a preset position
number by rotating it.
cSelect OK using the arrows button and press
the SET button.
The PRESET/AUTO PAN window will be closed and the
camera will move to the selected preset position.
When selecting CANCEL using the arrows button and
press the SET button, the PRESET/AUTO PAN window will
be closed.
cPress a camera selection button 
([1] - [10/0] for the WJ-HD316, [1] - [9], [0] for
the WJ-HD309) to register a preset position
number.
The pressed button number will be registered as a preset
position number.
The jog dial also can be used to select a preset position
number by rotating it.
Up to 64 can be registered as a preset position number.
vSelect OK using the arrows button and press
the SET button.
The adjusted camera position (currently displayed on the
monitor) will be registered as a preset position with the
selected preset position number.
To cancel the selected preset position, select CANCEL
using the arrows button and press the SET button. The set-
ting will be canceled and the REGISTRATION PRESET
POSITION window will be closed.
R
2 RMONITOR1
MONITOR21
5
9
13
2
6
10/0
14
3
7
11
15
4
8
12
16
SEQ SHIFT OSD
STOPPLAY PAUSEREC - REC STOP
ZOOM/
FOCUS
TEXTCOPYDISK SELECT
EL-ZOOM
MARK
LOGOUTIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWD
PAN/TILTSLOW
[WJ-HD316]
LOGOUT
R
2 RMONITOR1
MONITOR21
4
7
2
5
8
0
3
6
9
TEXT SEQ SHIFT OSDZOOM/
FOCUSCOPYDISK SELECT
EL-ZOOM
MARKIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWDSTOPPLAY PAUSEREC - REC STOP
PAN/TILTSLOW
[WJ-HD309]
PAN/
TILT
PAN/
TILT
z
cc
x
z
cc
x
PRESET / AUTO PAN
PRESET NUMBER
PRESET
AUTO PAN32
OK CANCEL
R
2 RMONITOR1
MONITOR21
5
9
13
2
6
10/0
14
3
7
11
15
4
8
12
16
SEQ SHIFT OSD
STOPPLAY PAUSEREC - REC STOP
ZOOM/
FOCUS
TEXTCOPYDISK SELECT
EL-ZOOM
MARK
LOGOUTIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWD
PAN/TILTSLOW
[WJ-HD316]
LOGOUT
R
2 R
MONITOR1
MONITOR21
4
7
2
5
8
0
3
6
9
TEXT SEQ SHIFT OSDZOOM/
FOCUSCOPYDISK SELECT
EL-ZOOM
MARKIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWDSTOPPLAY PAUSEREC - REC STOP
PAN/TILTSLOW
[WJ-HD309]
PAN/
TILT
PAN/
TILT
v
cc v
v
cc v

Add page 44 to Favourites

							44
Note:To move the camera to another registered preset
position, press the SET button after selecting a desired
preset position number in step 2. The PRESET/AUTO
PAN window will not close and it is possible to select
another preset number.
■ Auto Function (Auto Pan, etc)
Moves a camera with an auto function set in advance.
Important:
When the monitor 1 is selected, it is impossible to move
a camera with an auto function by performing the fol-
lowing steps.
In this case, perform the settings using the setup menu
of camera.
zPress the PRESET/AUTO button.
The PRESET/AUTO indicator will light and the PRESET/
AUTO PAN window will be displayed.
xMove the cursor to AUTO PAN using the
arrows button and check the radio button next
to AUTO PAN using the jog dial.
cSelect OK using the arrows button and press
the SET button.
The PRESET/AUTO PAN window will be closed and auto
function will start.
During auto action, it is impossible to register a preset posi-
tion. To close the PRESET/AUTO PAN window, select CAN-
CEL using the arrows button and press the SET button.
The setting will be canceled and the PRESET/AUTO PAN
window will be closed.
R
2
R
1
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
zx
xcc
PAN/
TILT
PRESET / AUTO PAN
PRESET NUMBER
PRESET
AUTO PAN32
OK CANCEL

Add page 45 to Favourites

							Event Action
45
ABOUT THE EVENT FUNCTION
The event action will be performed when the following
events occur.
•
Motion detection:When motion is detected by the
motion detection function (see below), this is stated as
an event of motion detection.
•
Video Loss:When a video signal supply is stopped
because of a cable disconnection or malfunction of a
camera, this is stated as an event of video loss.
•
Terminal alarm:When a signal is supplied from an
external device such as a door sensor to the ALARM
terminal, this is stated as an event of the terminal alarm.
•
Command alarm:When a command alarm is supplied
from a PC connected to the SERIAL connector on the
rear panel of this unit, this is stated as an event of the
command alarm.
About the Motion Detection Function (VMD)
An alarm signal will be supplied when motion (luminance
transition) is detected in a designated area. It is possible to
save images recorded in the place where motion is detect-
ed, or send e-mails when motion is detected.
Refer to a system administrator for further information about
the required settings for the motion detection function such
as the settings of the detection area.
■Action at an event occurrence
The event action will be performed according to the set-
tings when an event occurs.
There are 2 event action modes for the alarm mode
(ALARM) and the activity detection mode (ACT DET) for
each event type. The event action will be different accord-
ing to the event action mode set.
When an event of the alarm mode (ALARM) occurs, this unit
activates the alarm action.
About the event action mode
●Alarm Mode (ALARM)
This mode announces an event occurrence outside. Action
taken in the alarm mode is referred to as the alarm action.
●Activity Detection Mode (ACT DET)
This mode records images in the place where an event
occurred without announcing it.
✓: Applicable  – : Not applicable
* : Available only when using a PC via a network (Refer to
the Network Setup Instructions (PDF) for further informa-
tion.)
Alarm ModeActivity Detection
Mode
Start recording
Displays event information
on the monitor.
Sounds the buzzer.  Blinks the alarm indicator.
Switches from a displayed
image to the image from the
location of the alarm occur-
rence.
* Moves a camera to the
preset position. 
* Announces an event
occurrence by sending e-
mails.
* Announces an event
occurrence by the
PS·Data/Serial (RS232C)
commands.
Supplies a signal from the
ALARM connector or the
ALARM/CONTROL connec-
tor on the rear panel of this
unit (Alarm signal output).
Records the event log.
* Transmits images to an
FTP server
✓
✓
✓ ✓
✓
✓
✓
✓
✓
✓
✓✓
–
– –
–
✓
–
–
✓
–

Add page 46 to Favourites

							46
■ Alarm Function
● Blinks the ALARM indicator on the front
panel
● Switches from the images displayed on
monitor 1 and monitor 2 to the images from
the location of the alarm occurrence (on a
single screen)
● Displays the event information in the alarm
display area on monitor 1 and the camera
title display area on monitor 2


● Sounds the buzzer
Contact a system administrator about sounding duration.
● Announces an event occurrence to the con-
nected system device (Alarm Output)
Sends a signal to the device connected to the
ALARM/CONTROL connector, and the connected device
such as a buzzer will be activated.
● Starts recording automatically
Starts recording the image from the location of the event
occurrence automatically.
● Moves a camera to the preset position
A camera will move to the preset position registered in
advance.
● Announces an event occurrence by sending
e-mails
E-mails will be sent to addresses registered in advance.
Refer to the Network Operating Instructions (PDF) on the
provided CD-ROM.
ALARMTIMER
HDD 2
ERROR
HDD 1 ALARM
SUSPEND
ALARM
RESETOPERATE
MONITOR1
MONITOR21
4
7
2
5
8
0
TEXT SEQ SHIFT
COPYDISK SELECT
EL-ZOOM

Add page 47 to Favourites

							47
■ Cancel the Alarm Action
When an alarm has occurred, this unit will start the alarm
action according to the selected alarm action mode.
To cancel the alarm action, press the ALARM RESET but-
ton.
When ON is selected for Alarm Auto Reset (on the Alarm
Setup menu of Event), the following will be performed
automatically even if the alarm action is not canceled by
pressing the ALARM RESET button on the front panel.
•The ALARM indicator will stop blinking and light steadi-
ly
•The displayed alarm information will disappear
•The buzzer will stop beeping
zPress the ALARM RESET button to cancel the
alarm actions.
The ALARM indicator will go off.
■ Suspend the Alarm Actions
It is possible to suspend (deactivate temporarily) the alarm
actions even when an event has occurred.
This function will be useful when it is necessary not to acti-
vate the alarm actions for a certain period, such as when
configuring the system. However, images and event logs
will be recorded even when alarm actions are suspended.
● To suspend (deactivate temporarily)
the alarm actions
zPress both the ALARM RESET button and the
SET button at the same time.
The ALARM SUSPEND indicator will light.
● To stop suspending the alarm
actions
xPress both the ALARM RESET button and the
SET button at the same time again.
The ALARM SUSPEND indicator will go off.
Note:When an external switch is connected to the
ALARM/CONTROL connector on the rear panel, it is
possible to suspend the alarm actions using the exter-
nal switch.
In this case, the alarm actions will be suspended when
the external switch is on.
To stop suspending the alarm actions, set the external
switch to off.
MTIMER
HDD 2 ERROR
HDD 1
D
ELOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–ALARM
RESET
PAN/
TILT
zxzx
ALARMTIMER
HDD 2
ERROR
HDD 1 ALARM
SUSPEND
ALARM
RESETOPERATE
MONITOR1
MONITOR21
5
9
13
2
6
10/0
14
3
7
11
15
4
8
12
16
SEQ SHIFT OSDPAN/
TILT
STOPPLAY
ZOOM/
FOCUSTEXTCOPYDISK SELECT
EL-ZOOM
MARK
LOGOUTIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEA
BUSY
PAN/TILTSLOW
z

Add page 48 to Favourites

							48
It is available to copy (duplicate) manually the recorded
images in the copy area of the built-in hard disk to the
external recording device (DVD-RAM disk, DVD-R disk,
CD-R disk) connected to the unit.
It is recommended to make back-up copies on a regular
basis for unexpected situations such as malfunction of the
hard disk.
Manual copy is available during the following.
•While displaying live images
•While pausing playback of recorded images
•When displaying a searching window (Recording event
list window, VMD search list window, Marking list win-
dow)
(Manual copy is not available when a thumbnail window
is displayed.)
Notes:
•The auto copy function is available for copying record-
ed images to the DVD-RAM disk automatically. When
the auto copy function is enabled, manual copy is not
available. Refer to a system administrator for further
information about the auto copy function.
•To copy during playback of recorded images, pause
playback temporarily.
•To copy recorded images on the DVD-RAM disk, for-
matting (initializing) the DVD-RAM disk is required in
advance. Refer to page 52 for the descriptions of how
to format DVD-RAM disks.
zPress the SHIFT button.
The SHIFT indicator will light.
To copy recorded images during playback, pause the play-
back temporarily.
xPress the COPY button.
The DATA COPY window will be displayed on monitor 2
and the VGA monitor.
The DATA COPY window will not be displayed when a
thumbnail window is displayed.
In this case, display a list window using the arrows button
(
CD).
cPerform the settings for data copy (camera
channel, time range, the disk on which images
are to be copied). Move the cursor to each set-
ting item using the arrows button and select a
parameter by rotating the jog dial.
Note:Time range to be set for PERIOD should be 30 min-
utes or less to copy images at one try.
COPYING (Duplicate)
R
2 RMONITOR1
MONITOR21
5
9
13
2
6
10/0
14
3
7
11
15
4
8
12
16
SEQ SHIFT OSD
STOPPLAY PAUSEREC - REC STOP
ZOOM/
FOCUS
TEXTCOPYDISK SELECT
EL-ZOOM
MARK
LOGOUTIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWD
PAN/TILTSLOW
[WJ-HD316]
LOGOUT
R
2 R
MONITOR1
MONITOR21
4
7
2
5
8
0
3
6
9
TEXT SEQ SHIFT OSDZOOM/
FOCUSCOPYDISK SELECT
EL-ZOOM
MARKIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWDSTOPPLAY PAUSEREC - REC STOP
PAN/TILTSLOW
[WJ-HD309]
PAN/
TILT
PAN/
TILT
zxcc
zxcc
DATA COPYCAMERA
PERIOD
COPY DRIVE.
JAN 1 0312 05 AM JAN103 12 12345678
910111213141516
00 AM .:
OK CANCEL HDD COPY AREA
COPY 1COPY 2
.. :

Add page 49 to Favourites

							49
vSelect the OK button using the arrows button
and press the SET button.
The DATA COPY window will be closed and data copy will
start.
The copy icon will be displayed on the task bar during
copying.
To close the DATA COPY window, select CANCEL using
the arrows button and press the SET button. The setting will
be canceled and the DATA COPY window will be closed.
When the selected COPY DRIVE is not found, copying will
not start and the DATA COPY window will not be closed
even when the SET button is pressed after selecting OK.
Important:
•To eject the disk, do the following during live images
are displayed.

Confirm the SHIFT indicator is lit. Then, press the cam-
era selection button [10/0] and [1] ([0] and [1] for the
WJ-HD309) simultaneously for 2 seconds or more.

Confirm the SHIFT indicator is lit. Then, press the cam-
era selection button [10/0] and [2] ([0] and [2] for the
WJ-HD309) simultaneously for 2 seconds or more.
•Copying will be performed in the following order:
Viewer Software 
→Images →Audio
Depending on the set time range for PERIOD, some of
images and audio may not be copied.
Copy icon
R
2
R
1
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
vv
PAN/
TILT

Add page 50 to Favourites

							50
Perform the settings for the built-in hard disk of the unit, the
optional extension unit and the DVD-RAM disk. These are
the descriptions of how to delete recorded images on the
hard disk and how to format a DVD-RAM disk.
Refer to a system administrator for further information about
the other disks.
■ Deletion of recorded images
saved on the hard disk manually
Delete recorded images saved in the normal area or the
event area of the built-in hard disk or the optional extension
unit manually.
By setting a time and date, images in the normal record
area of the hard disk recorded before the set time and date
will be deleted.
It is recommended to delete manually when available disk
space is running out.
Important:
It is impossible to recover the deleted images.
Note:It is possible to delete recorded images automatically
when the set days have passed from the day the image
was recorded (Auto Delete). Refer to a system adminis-
trator for further information.
zPress the SETUP/ESC button for 2 seconds or
more.
The SETUP MENU will be displayed on monitor 2 and the
VGA monitor.
xMove the cursor to Maintenance using the
arrows button (
CDAB) and press the SET
button.
cMove the cursor to Data Delete using the
arrows button (
CD).
The Data Delete menu will be displayed.
vPress the SET button.
The cursor will be displayed on the Data Delete menu.
DELETE DATA ON THE DISK
R
2 R
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
z
vxc
PAN/
TILT
REC Rate
Disk Info
Version Info
Disk End Mode
Disk Capacity
Date Delete
Event Log
Error Log
Access Log
SET UP MENURecording Event Schedule
System
Display Comm SwitcherLIVEMaintenance
SUPER FINE
FINE
NORMAL
EXTENDED
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips CAM 1
CAM 2
CAM 3
CAM 4
CAM 5
CAM 6
CAM 7
CAM 8
CAM 9
CAM 10
CAM 11
CAM 12
CAM 13
CAM 14
CAM 15
CAM 16MANU SCHEPOST EVTEMRPRE EVT
EventScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
REC Rate
Disk Info
Version Info
Disk End Mode
Disk Capacity
Data Delete
Event Log
Error Log
Access Log
■ Auto Delete■ Manual Delete for Normal Recording Area
                      Delete before   JAN  .    01    .   03
 
■ Manual Delete for Event Recording Area
                      Delete before   JAN  .    01    .   03 ■ Disc Format of DVDCOPY1
COPY2
DELETE
FORMATFORMAT
OFF
DELETE
REC Rate
Disk Info
Version Info
Disk End Mode
Disk Capacity
Date Delete
Event Log
Error Log
Access Log
SET UP MENURecording Event Schedule
System
Display Comm SwitcherLIVEMaintenance
SUPER FINE
FINE
NORMAL
EXTENDED
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips
1ips CAM 1
CAM 2
CAM 3
CAM 4
CAM 5
CAM 6
CAM 7
CAM 8
CAM 9
CAM 10
CAM 11
CAM 12
CAM 13
CAM 14
CAM 15
CAM 16MANU SCHEPOST EVTEMRPRE EVT
EventScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
REC Rate
Disk Info
Version Info
Disk End Mode
Disk Capacity
Data Delete
Event Log
Error Log
Access Log
■ Auto Delete■ Manual Delete for Normal Recording Area
                      Delete before   JAN  .    01    .   03
 
■ Manual Delete for Event Recording Area
                      Delete before   JAN  .    01    .   03 ■ Disc Format of DVDCOPY1
COPY2
DELETE
FORMATFORMAT
OFF
DELETE

All Panasonic manuals Comments (0)

Related Manuals for Panasonic Digital Disk Recorders Wj Hd316 Operating Instructions