Panasonic Digital Hd Plasma Tv Th 50xvs30 Operating Instructions
Have a look at the manual Panasonic Digital Hd Plasma Tv Th 50xvs30 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
11 Connection 12 DEDICATED RECEIVER INSERVICE USE 1 2 1 2SPEAKERS Terminals (R)SPEAKERS Terminals (L) – Cable fixing bands Secure any excess cables with bands as required. Note: Please turn off the power of the Plasma Display unit and Digital Media Receiver when connecting or removing Display - Receiver cable. Display connection When connecting the speakers, be sure to use only the optional accessory speakers. For details on installation and connection of the speaker, refer to the Speaker’s Installation Manual. (Optional) Speakers (Optional accessories) Pass the attached cable fixing band through the clip as shown in the figure.To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band.AC cord connection (see page 19) To tighten: To loosen: Pull Pull Push the catch 3. Slide up the clamper and fix the AC cord plug securely. 2. Insert the AC cord and close the clamper securely. 1. Open the clamper. ClamperAC cord Note: The power plug in the illustration may not be the type fitted to your set.To loosen the clamper: – AC cord fixing To DEDICATED DISPLAY OUT connector on Digital Media Receiver These terminals are not in use.
12 •For proper reception of VHF/UHF channels, an external antenna is required. For best reception, an outdoor antenna is recommended. •When you enjoy terrestrial TV programs only, connect the home antenna to ANTENNA (A). •When you enjoy cable TV programs only, connect the cable TV’s cable to ANTENNA (A). •When you enjoy both the terrestrial TV programs and the cable TV programs, connect the cable TV’s cable to ANTENNA (A), and the terrestrial antenna cable to ANTENNA (B). •Select the antenna mode in Input Setup (see page 22). LLPBLPB PRRPR 2AUDIOAUDIO AUDIO OUTCOMPONENT VIDEO INPUTPROG OUTINPUT Cable In DEDICATED DISPLAY OUT SERVICE ONLY ANTENNA ABDIGITAL AUDIO OUT AUDIO AUDIOL RVIDEOS VIDEO1 YY R L R R2 1 CABLE INANTENNA A B CableCARDTM CARD TOP (Turn Card upside down and gently insert it.) AUDIOCable In DEDICATED DISPLAY OUT SERVICE ONLY ANTENNA ABDIGITAL AUDIO OUT LR CABLE INANTENNA A B LLPBLPB PRRPR 2AUDIO AUDIO OUTCOMPONENT VIDEO INPUTPROG OUTINPUT AUDIO AUDIOL RVIDEOS VIDEO1 YY RR 2 1CableCARDTM CARD TOP (Turn Card upside down and gently insert it.) Connection VHF UHF Mixer 75 Ohm coaxial cable Connection to the display CableCARDTM CARD TOP (Turn Card upside down and gently insert it.)AU DI OCable In DEDICATED DISPLAY OUT SERVICE ONLY ANTENNA ABDIGITAL AUDIO OUT LR DEDICATED DISPLAY OUT LLPBLPB PRRPR 2AUDI O AUDIO OUTCOMPONENT VIDEO INPUTPROG OUTINPUT AUDIO AUDIOL RVIDEOS VIDEO1 YY RR 2 1 Cable / Antenna Connection Notes: •Install the Digital Media Receiver at least 15.7 inch (40 cm) away from the Plasma Display to avoid interference. •Be sure the power to the Plasma Display and digital media receiver is OFF before connecting cables. •Do not remove the cable connecting the display and tuner unit while the power is on. If the cable is removed inadvertently, turn off the display and digital media receiver before reconnecting the cable. orIncoming Cable signal Either cable TV or home antenna connection Both cable TV and home antenna connection Incoming Cable signal Home antenna VHF UHF Home antenna Mixer
13 Connection AV Connection CableCARDTM CARD TOP (Turn Card upside down and gently insert it.)AUDIO SERVICE ONLY LR Cable In DEDICATED DISPLAY OUT ANTENNA ABDIGITAL AUDIO OUT LLPBLPB PRRPR 2 AUDIO AUDIO OUTCOMPONENT VIDEO INPUTPROG OUTINPUT DIGITAL AUDIO OUT AUDIO AUDIO L R VIDEO S VIDEO1 YY RR 2 1LLPBLPB PRRPR 2AUDIO AUDIO OUTCOMPONENT VIDEO INPUTPROG OUTINPUT AUDIO AUDIOL RVIDEOS VIDEO1 YY RR 2 1 VCR Connection OUTPUTDIGITAL AUDIO OUT INPUT AUDIOL R VIDEO S VIDEO 21 AUDIOL R VIDEO S VIDEO LLPBLPB PRRPR 2 AUDIO AUDIO OUTCOMPONENT VIDEO INPUTPROG OUTINPUT AUDIO AUDIO L R VIDEO S VIDEO1 YY RR 2 1 S Video cable AV cable S VCR Notes: •Certain cable systems offset some channels to reduce interference or have Premium (scrambled) channels. A cable converter box is required for proper reception. Check with your local cable company for its compatibility requirements. •To obtain optimum quality picture and sound, from an antenna, the correct cable (75 Ohm coaxial) and the correct terminating plug are required. •If a communal antenna system is used, you may require the correct connection cable and plug between the wall antenna socket and your television receiver. •Your local television service center or dealer may be able to assist you in obtaining the correct antenna system for your particular area and the accessories required. •Any matters regarding antenna installation, upgrading of existing systems or accessories required, and the costs incurred, are your responsibility. Note: The S Video input will override the composite video signal when S Video cable is connected. Connect either S Video cable or Video cable.
14 DIGITAL AUDIO OUT LPB RPRCOMPONENT VIDEO INPUT AUDIO YLLPBLPB PRRPR 2 AUDIO AUDIO OUTCOMPONENT VIDEO INPUTPROG OUTINPUT AUDIO AUDIO L R VIDEO S VIDEO1 YY RR 2 1 AUDIO OUTPUT DIGITAL TV OUTPUT RL PB PR Y DIGITAL AUDIO OUT RROG OUT LLPBLPB PRRPR 2 AUDIO AUDIO OUTCOMPONENT VIDEO INPUTPROG OUTINPUT AUDIO AUDIO L R VIDEO S VIDEO1 YY RR 2 1INPUT AUDIOL R VIDEO This TV is capable of displaying 480i, 1080i and 480p DTV signals when connected to a DTV Tuner Set-Top-Box (STB) or using the internal DTV Tuner. This TV also utilizes a progressive scan doubler, which de-interlaces the NTSC signal and progressively scans the image. This allows you to sit close to the TV and not see the thin black horizontal lines (venetian blind effect) associated with interlaced TV pictures. •To view DTV programs, connect the STB to the component video input terminals (Y, P B , PR) of the TV. Component color inputs provide luminance and separate color signal. •Select the output of the STB to either 480i, 1080i or 480p. •A DTV signal must be available in your area. •Use a Panasonic DTV-STB (Digital TV-Set-Top Box) or DVD Player. Digital TV - Set-Top Box (DTV-STB) or DVD Connection Set Top Box DVD playerComponent Video cable Connection See optional equipment manual for further instructions for recording and monitoring. Program Out Connection (PROG OUT) VCR DVD recorder MONITOR AV cable Notes: •When a device (STB, DVD, etc.) is connected to the HDMI terminal (see page 16), no video or audio is output due to license restrictions. •Program Out signal may not be available when COMPONENT input (see page 20) is selected for the Main picture during PIP or SPLIT operation (see pages 52, 54). •When receiving digital channel signals, all digital formats are down-converted to composite NTSC video to be output through Program Out terminals. •Some programs contain Macrovision signal to prevent VCR recording.Audio cable
15 Connection LLPBLPB PRRPR 2 AUDIO AUDIO OUTCOMPONENT VIDEO INPUTPROG OUTINPUT DIGITAL AUDIO OUT AUDIO AUDIO L R VIDEO S VIDEO1 YY RR 2 1 LAUDIO OUT DIGITAL AUDIO OUT R AUDIO INPUTOPTICAL IN R L Amplifier Connection For a full Home Theater sound experience, an external Dolby Digital∗ decoder and a multichannel amplifier must be connected to the DIGITAL AUDIO OUT terminal on the TV. ∗Dolby Digital 5.1 channel surround sound delivers digital-quality sound. Dolby Digital provides five discrete full-bandwidth channels for front left, front right, center, surround left and surround right, plus a LFE (Low Frequency Effect) subwoofer channel. Notes: •External speakers cannot be connected directly to AUDIO OUT terminals. •When ATSC channel is selected, the output from the DIGITAL AUDIO OUT jack will be Dolby Digital. When NTSC channel is selected, the output will be PCM. Procedure 1. Select Speakers “Off” in Audio menu (see page 29). 2. Adjust the amplifier volume to the desired level.Optical digital audio cable Audio cable Amplifier or DIGITAL MEDIA RECEIVER TU-PT700USD CARDPC CARD MENU OK TV/VIDEO VOLUMECHANNELINPUT 3 PC S VIDEO VIDEO L-AUDIO-R INPUT 3 PC S VIDEO VIDEO VIDEO L-AUDIO-R OUTPUT AUDIOR L VIDEO SVIDEO Front AV Connection Push to open the front panel and connect equipment to front Audio/Video input terminals. A second VCR, video disc player, video game equipment and DSS equipment can also be connected to the video input terminals. See the optional equipment manual for details. Notes: •The S VIDEO connection provides higher quality picture. It overrides other VIDEO connections. •If the connecting equipment has a S Video terminal, connect a S Video cable.CAMERA RECORDER AV cable S Video cable
16 AUDIO L R SERVICE ONLY CableCARDTM CARD TOP (Turn Card upside down and gently insert it.)AUDIOCable In DEDICATED DISPLAY OUT ANTENNA ABDIGITAL AUDIO OUT LR LLPBLPB PRRPR 2AUDIO AUDIO OUTCOMPONENT VIDEO INPUTPROG OUTINPUT AUDIO AUDIOL RVIDEOS VIDEO1 YY RR 2 1 AUDIO OUTPUT HDMI signal out RL Connection HDMI Connection HDMI∗1 (High Definition Multi media Interface) is the first all digital consumer electronics A/V interface that supports uncompressed standard. The HDMI terminal supports both video and audio information. To the HDMI∗ 1 input terminal, you can connect an EIA/CEA-861/861B∗2 compliant consumer electronic device, such as a Set Top Box or DVD player with HDMI or DVI output terminal. Input a High-bandwidth Digital Content Protection (HDCP) high-definition picture source to this HDMI terminal, so you can display the high-definition pictures on this TV in the digital form. ∗1. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. ∗2. EIA/CEA-861/861B profiles compliance covers profiles for transmission of uncompressed digital video including high bandwidth digital content protection. ∗3. Consult your consumer electronics dealer for availability details. [for USA] HDMI-DVI conversion cable (TY-SCHO3DH): available on Panasonic Website (www.panasonic.com). Notes: • An audio cable should be connected only when using a HDMI conversion adapter to connect with a DVI cable. • If the external device has DVI output only, use a DVI to HDMI adapter cable∗ 3 to connect to the HDMI terminal. • Connect the audio cables to the AUDIO IN terminals for HDMI. • Select the audio setting in HDMI In (see page 29). This input terminal is not intended for use with computers. Notes: •This HDMI connector is Type A. •If you connect an equipment without a digital output terminal, connect to the COMPONENT VIDEO, S VIDEO or VIDEO input terminal on the TV so you can enjoy an analog signal. •The DIGITAL IN terminal can only be used with 1080i, 480i or 480p picture signals. Set the Digital Set -Top -Box DIGITAL OUT terminal Output setting to 1080i, 480i or 480p. For detailed information, refer to the Digital Set -Top -Box instruction manual. If you cannot display the picture because your Digital Set -Top -Box does not have a DIGITAL OUT terminal Output setting, use the component Video Input (or the S Video Input or Video Input). In this case the picture will be displayed as an analog signal.HDMI cableSet Top Box DVD player Audio cable 1080i 480p 480i No. of dots (H × V) 1,920 × 1,080i 720 × 480p 640 × 480p 720(1,440) × 480i Vertical scanning frequency (Hz) 59.94/60 59.94/60 59.94/60 59.94/60 Compatible VIDEO Signal Compatible sampling frequency of AUDIO signal through HDMI (L.PCM) : 48kHz / 44.1kHz / 32 kHz
17 Connection PC Connection Notes: •Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.) •The maximum resolution: If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. •Some PC models cannot be connected to the set. •There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal. •The computer shown in the illustration is for example purposes only. •Additional equipment and cables shown are not supplied with this set. •Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. INPUT 3 PC S VIDEO L-AUDIO-R VIDEO DIGITAL MEDIA RECEIVER TU-PT700USD CARDPC CARD MENU OK TV/VIDEO VOLUMECHANNELINPUT 3 PC S VIDEO VIDEO L-AUDIO-R Signal Names for D-sub 15P Connector Pin Layout for PC Input Terminal 1 6 7 8 3 9 4 5 10 15 14 13 12 11 2 COMPUTER AudioStereo plug Connect a cable which matches the audio output terminal on the computer. Conversion adapter if necessary (purchase locally)RGB PC cableD-sub 15p System No. TH-50XVS30UM4:3 1,024 × 768 16:9 1,366 × 768 Aspect Pin No. 1 2 3 4 5 Signal Name R G B NC (not connected) GND (Ground) Pin No. 6 7 8 9 10 Pin No. 11 12 13 14 15 Signal Name GND (Ground) GND (Ground) GND (Ground) NC (not connected) GND (Ground) Signal Name NC (not connected) NC HD/SYNC VD NC
18 Connection CableCARDTM Connection CableCARDTM allows you to tune digital and high definition cable channels through the cable antenna. Consult your cable company on the availability of CableCARDTM. Notes: •If you experience keyboard or remote control function hang-up when using CableCARD TM, unplug the TV and plug it back on and try the controls again. If this condition still exists, please call Panasonic Customer Call Center for further instructions. •Do not insert a PCMCIA card into CableCARD TM slot. DIGITAL AUDIO OUT AUDIO DEDICATED DISPLAY OUT Cable InSERVICE ONLY ANTENNA ABLRCable InANTENNA A BSERVICE ONLY LLPBLPB PRRPR 2AUDIO AUDIO OUTCOMPONENT VIDEO INPUTPROG OUTINPUT AUDIO AUDIOL RVIDEOS VIDEO1 YY RR 2 1CableCARDTM CARD TOP (Turn Card upside down and gently insert it.)CableCARDTM CARD TOP (Turn Card upside down and gently insert it.) Insert the CableCARDTM into the slot with the front side facing down. Procedure 1. Connect the cable antenna to ANTENNA (A). 2. Insert the CableCARD TM (as its front side facing down) into CableCARDTM slot on the back of the Receiver. 3. Turn the TV on (see page 19). 4. Set the input mode to TV (see page 20). Follow the messages displayed on the screen.
19 Power ON / OFF DISPLAY OUT Remote Control Sensor Power Indicator Connecting the plug to the Wall Outlet Press the Power switch on the side of the Plasma Display to turn the set on: Power-On. Power Indicator: Blue Connecting the AC cord plug to the Plasma Display. Fix the AC cord plug to digital media receiver. Fix the AC cord plug securely to the Plasma Display with the clamper. (see page 11) Press the POWER button on the remote control to turn the Plasma Display off. Power Indicator: Red (standby) Press the POWER button on the remote control to turn the Plasma TV on. Power Indicator: Blue Turn the power to the Plasma TV on or off by pressing the POWER button on the Digital Media Receiver unit, when the Plasma TV is on or in standby mode. Note: The TV will still consume some power as long as the power cord is still inserted into the wall outlet.TVVCRDVD DBSRCVRCBL LIGHT TV/VIDEOA -ANTENNA - B SAP AUX ASPECT ER BBE POWER POWER C.A.T.S. sensor Plasma C.A.T.S. (Contrast Automatic Tracking System) Plasma C.A.T.S. automatically senses the ambient light conditions and adjusts the brightness and gradation accordingly, to optimize contrast. (Effective when Picture Mode is set to Auto.) Power switch Notes: •Do not remove the cable connecting the display and tuner unit while the power is on. If the cable is removed inadvertently, turn off the display and digital media receiver before reconnecting the cable. •Please turn off the power of the Plasma Display unit and Digital Media Receiver when connecting or removing Display - Receiver cable.Occasionally on-screen-menus appear while connection cable is not inserted, but these on- screen-menus are not effective. Remote control is not accessible to those menus.
20 TV MENU R-TUNE PIP MIN REWPIP MAX FF PLAYPROG EXIT VCRDVD DBSRCVRCBL LIGHT TV/VIDEOA -ANTENNA - B SAP 123 456 78 0 9 AUX ASPECT MUTERECALL BBE STOPPA U S E FREEZE TV/VCR PIP SPLIT MOVE SWAP SEARCHOPEN/CLOSESPLIT CH DVD/VCR CH REC CH VOL CHVOL OK POWER Component 2HDMI TVComponent 1 Video 3 PC Video 1 Video 2 POWER Turn the TV ON or OFF. TV/VIDEO Change the input mode. SD Access Photo Viewer (see page 46). R-TUNE Switch to previously viewed channel and input modes. Mode Selection buttons (see page 59, 60) Selects the operation mode for the remote control. The operation of each equipment can be done by this remote control. PIP MIN REWPIP MAX FFPLAY STOPPAUSE FREEZE TV/VCRSEARCHOPEN/CLOSESPLIT CH DVD/VCR CH REC FREEZE Freeze the picture (see pages 53, 55). PIP: PIP (Picture in Picture) Operation (see page 52-53) SPLIT: Split Screen (see page 54-55) MOVE: Move PIP frame (see page 53). SWAP: Swap pictures in PIP or SPLIT operation (see page 52, 54). DIGITAL MEDIA RECEIVER TU-PT700USD CARDPC CARDMENU OK TV/VIDEO VOLUME CHANNELINPUT 3 PCS VIDEO VIDEO L-AUDIO10-R SD CARDPC CARD MENU OK TV/VIDEO VOLUMECHANNEL Channel selectors POWER button MENU Display Main Menu or return one step backward in menus (see pages 24, 57). Volume adjusters OK Choose menu and submenu entry. TV/VIDEO Change the input mode. Operation of other Device (see pages 63, 64) PIP MIN, PIP MAX Change the size of PIP frame (see page 52). SEARCH Display search frames during PIP or SPLIT operation (see pages 53, 55). SPLIT CH Select the channel during PIP or SPLIT operation (see pages 52, 54).SD CARD slot PC CARD slot Location of Controls PC CARD EJECT button